Smeg KSPP90XC Instruction Manual page 9

FUMES DISCHARGE
(only intended for personnel qualified to assemble the hood)
When the kitchen hood is used simultaneously with other appliances that use gas or other fuels, the room must have sufficient ventila-
tion, in accordance with regulations in force.
ASSEMBLY INSTRUCTIONS
A
Phase page 4
• Place the support bar (S) on the installation wall at a height (H) from the cooker indicated in the figure (Fig.
• Use a spirit level to check the horizontal alignment and draw 2 marks at each end of the support bar, this is where the holes will be drilled (Fig.
2 3
- ).
• Drill the holes, insert 2 expansion plugs (ø 8mm) and fasten the bar with the relative screws (V1) (Fig.
The fixing kit (screws, plugs, and brackets) supplied with the hood can only be used on masonry walls: should it be necessary to
install the hood onto walls in a different material, assess other fixing systems keeping the wall resistance and weight of the hood in mind
(indicated on page 2).
B
Phase page 4
• Hook the hood onto the support bar (Fig.
• Adjust the alignment of the hood by using the fixing screws (Fig.
adjusts vertical scrolling.
• To prevent the hood from falling due to a pressure below, fasten it to the wall with expansion plugs and relative screws (V2) using the appropriate
holes on the back of the hood (Fig.
D
Phase page 4
EXTERNAL EXHAUST HOOD VERSION (SUCTION)
• Connect the air outlet connection of the hood to the external discharge with a suitable pipe.
E
Phase page 5
• Insert the extension (H) in the chimney (G) (Fig.
• With external exhaust (suction) versions, it is possible to insert extension (H) with the slots facing downwards so that they are not visible when
the installation height allows it.
F
Phase page 5
• Slide the extension (H) until it is positioned at the desired height (Fig.
• Following what is indicated in Fig.
• Place the bracket (L) on the wall by following the line drawn on it. With a spirit level, check the horizontal alignment and mark the 2 drilling points
3
at the ends (Fig. ).
• Drill the holes, insert 2 expansion plugs (ø 6mm) and fasten the bracket (L) with the relative screws (V4) (Fig.
• Tighten the extension (H) to the bracket (L) using screws (V5) (Fig.
• Electrically power the hood in accordance with regulations in force.
EXTERNAL EXHAUST HOOD VERSION (SUCTION)
In this version, the kitchen fumes and vapours are conveyed outside through an exhaust pipe.
The air outlet fitting that extends from the upper part of the hood must be connected with the pipe that conducts
the fumes and vapours to an external output.
Do not connect the equipment to discharge pipes of fumes produced from combustion (for example boil-
ers, fireplaces, etc) and you are to comply with the regulations in force regarding external air discharge.
The fumes outlet pipe must have:
- a diameter not less than that of the hood fitting;
- a slight slope downwards (drop) in the horizontal sections to prevent any formation of condensation from flowing
back to the hood;
- the minimum required number of bends;
- minimum required length (long pipes with various bends can reduce suction performance of the hood and trigger
vibrations of the check valve).
If the fumes outlet pipe passes through cold environments such as attics, etc., it is possible that water condensation
forms due to sudden changes in temperature. In this case, you are required to insulate the pipes.
(only intended for personnel qualified to assemble the hood)
1
).
3
).
1
) and fasten the assembly to the body of the hood using screws (V3)(Fig.
2
, draw a line on the wall that will be used to position the bracket (L) correctly.
2
). The upper screw (B) adjusts the distance from the wall, the lower one (C)
1
).
5
).
19
1
).
4
).
2
).
4
).