Pentair FRESHPOINT F3000-B2B Instruction Manual page 5

INSTALLATION CONTINUED
3. Mounting the Faucet
INSTALLATION CONTINUED
A. Apply 3-5 wraps of plumber tape to faucet stem.
B. Assemble faucet as shown in Figure 3.
3. Mounting the Faucet
C. Screw quick connector onto threaded end of faucet stem.
A. Apply 3-5 wraps of plumber tape to faucet stem.
D. Place a mark 5/8" from one end of the blue tubing. Wet the
B. Assemble faucet as shown in Figure 3.
end of the 3/8" tube and push into bottom of connector. The
C. Screw quick connector onto threaded end of faucet stem.
5/8" mark should be flush with the collar of the connector.
D. Place a mark 5/8" from one end of the blue tubing. Wet the
NOTE: To remove the tube, push on the fittings' collar and pull
end of the 3/8" tube and push into bottom of connector. The
the tube out.
5/8" mark should be flush with the collar of the connector.
E. Holding the faucet, feed the tubing through the hole in the
NOTE: To remove the tube, push on the fittings' collar and pull
the tube out.
sink. Position the faucet handle at a desired location.
E. Holding the faucet, feed the tubing through the hole in the
F. Center the faucet and slip slotted disc between the bottom
sink. Position the faucet handle at a desired location.
of the counter or sink and lock washer. Tighten the stem
nut with a wrench until it is tight.
F. Center the faucet and slip slotted disc between the bottom
of the counter or sink and lock washer. Tighten the stem
G. Firmly insert spout into faucet base.
nut with a wrench until it is tight.
4. Mounting the System
G. Firmly insert spout into faucet base.
A. Select a location under the sink, or other suitable area
4. Mounting the System
where the system will be installed.
A. Select a location under the sink, or other suitable area
NOTE: The system carton can be used to determine the
where the system will be installed.
operational footprint required for installation of the
NOTE: The system carton can be used to determine the
system and replacement cartridges. (Figure 4a)
operational footprint required for installation of the
B. Mount the system vertically. Ensure mounting is level.
system and replacement cartridges. (Figure 4a)
Place a pencil mark in the upper slots of the bracket
B. Mount the system vertically. Ensure mounting is level.
mounting holes. (Figure 4b). Alternate mounting option: If
Place a pencil mark in the upper slots of the bracket
mounting the system near the floor, place the pencil marks
mounting holes. (Figure 4b). Alternate mounting option: If
above each of the mounting holes on the bracket to ensure
mounting the system near the floor, place the pencil marks
enough space resides below the cartridge and the floor for
above each of the mounting holes on the bracket to ensure
cartridge replacement (Figure 4c). Use the 3/32" drill bit to enough space resides below the cartridge and the floor for
create pilot holes for mounting. cartridge replacement (Figure 4c). Use the 3/32" drill bit to
create pilot holes for mounting.
The system should be mounted to a firm, solid
WARNING:
The system should be mounted to a firm, solid
surface that is able to support the weight of the
WARNING:
surface that is able to support the weight of the
system.
system.
4b
4b
4c
4c
3
3
Faucet Stem
Chrome
Plate
Faucet Stem
Rubber
Chrome Washer
Plate
Rubber
Slotted
Washer
Disk
Slotted
Lock Washer
Disk
Stem Nut
Lock Washer
Stem Nut
Quick
Connector
3/8" Tubing
Quick
Connector
3/8" Tubing
4a
4a
16.25" (413 mm)
16.25" (413 mm)
Filter
Filter
Filter
Filter
F3000-B2B, F3000-B2M Filtration Systems Instruction Manual • 5
F3000-B2B, F3000-B2M Filtration Systems Instruction Manual • 5
262.634.2386 | greatlakesintl.com
Counter Top
Counter Top
7" (178 mm)
7" (178 mm)
Inlet
Inlet
14" (356 mm)
14" (356 mm)
Outlet
Outlet