Page 1: Table Of Contents
Warranty, Sales, Service, and Training Information Hotwire 6301/6302 IDSL Routers Overview ® Hotwire 6301 and 6302 IDSL (Integrated Services Digital Network Digital Subscriber Line) Routers are components in the Hotwire DSLAM (Digital Subscriber Line Access Multiplexer) system. Hotwire 6301 IDSL Router with one Ethernet port...
Page 2 Internet or corporate LAN access over a combination of traditional twisted-pair copper telephone wiring and ISDN transport, such as T1 or fiber. These products have three data channels that are configurable for a total of 144 kbps. Network with a Hotwire 6301 IDSL Router Central Remote...
Page 3: Product Documentation Online
If installing the router on the wall instead of a table or desk, refer to Placement on page 18 before installing the router and cables. NOTE: In this document: — End-user system is used to represent any host with an Ethernet connection.
Page 4: Wiring And Cables You Will Need
Refer to Installing the Hotwire 6301/6302 IDSL Router Optional Cable and Adapters Hotwire 6301/6302 IDSL Routers are typically configured remotely by the service provider. The following optional cable and adapters are only used when configuring the router locally: Console cable: Straight-through cable with 8-pin, non-keyed modular plugs (Part No.
Page 5: Installing Dsl Access Wiring
Installing DSL Access Wiring The local loop terminates at the punchdown block or NID (Network Interface Device). Cables must be connected from the customer premises side of the punchdown block or NID to an RJ11 jack. Typically, the punchdown block is installed in commercial locations and the NID is installed in residential locations.
Page 6: Connecting To The Dsl Access Wiring
Connecting to the DSL Access Wiring The Hotwire 6301 or 6302 IDSL Router connects to the local loop via wiring from the demarcation point to an RJ11 wall jack. The DSL twisted-pair wiring from the local loop terminates at a new or existing wall jack. It may be necessary to install a standard single RJ11 jack or replace a single jack with a double RJ11 jack.
Page 7: Installing The Hotwire 6301/6302 Idsl Router
Place the IDSL Router on a flat surface with clearance for the rear connectors. NOTE: The following illustrations show the Hotwire 6302 IDSL Router with a 4-port Ethernet hub. The Hotwire 6301 IDSL Router is identical except that it has one Ethernet port. For router cable pin assignments, refer to Procedure 1.
Page 8 3. If installing the Hotwire 6301 IDSL Router: — Use a straight-through cable to connect the other end of the cable to an Ethernet hub. Do not connect to the hub’s optional Uplink connection with a straight-through cable (requires an Ethernet crossover cable).
Page 9 VT100-compatible terminal or a PC running a terminal emulation program. It is an optional connection that is only used for local configuration of the router. To set up the VT100 terminal or PC for local configuration and to access the Configuration Setup router, refer to Connect the DB9 adapter to the PC and connect the cable to a PC or laptop.
Page 10: Power-On
Power-On When power is applied, the router performs self-diagnostics and the PWR LED is on. The self-diagnostics include a power-on self-test. During the power-on self-test, all of the LEDs turn on for one second.
Page 11: Status Leds
The DSL link is active and ready to transmit and receive data. No DSL link has been established. Data transmission is in progress on the DSL line. No data is being transmitted or received by the router. The Ethernet connection is active. No Ethernet device is detected.
Page 12: Troubleshooting
PC is connected and powered on. Verify that the correct cable is installed. For a Hotwire 6301 IDSL Router, refer to 6302 IDSL Router, refer to Verify that the DSL LINE cable is securely installed on both ends.
Page 13 LED Symptom PWR LED is off. TST LED is on. Action Check that the power cord is securely installed on both ends. If no LEDs are on, the power supply may be defective. Test the outlet to verify power. If other LEDs are on, the PWR LED may be burned out. Unplug the unit and reapply power;...
Page 14: Configuration Setup
Stop bits is set to 1. Flow control is set to Off or None. Accessing the Router When the local console connection is first established, access control to the IDSL router displays an initial prompt of Login>. Procedure 1. At the initial prompt of Login>, enter the factory default Login ID of paradyne.
Page 15: Cables And Connectors
Cables and Connectors Refer to Installing the Hotwire 6301/6302 IDSL Router information. Use a CAT3, or better, cable for the DSL line. The DSL interface uses a 6-pin, non-keyed modular plug. RJ11 6-Pin Connector Pin # Function 1 & 2 Not used...
Page 16 7 & 8 Not used – or – — To connect a Hotwire 6301 IDSL Router to a PC with an Ethernet NIC card, or a Hotwire 6302 IDSL Router to an external hub, use an Ethernet crossover cable. 8-Pin Ethernet Crossover Cable...
Page 17 The Console connector uses 8-pin, non-keyed modular plugs and a DB9 adapter. Step 5 on page 9. RJ45 8-Pin Connector Pin # Circuit Not used 4 & 5 Signal Ground Not used 8-Pin Modular to DB9 Adapter Plug Modular Pin # Circuit 4 &...
Page 18: Optional Wall Placement
Optional Wall Placement Hotwire 6301 and 6302 IDSL routers are designed for tabletop placement. The IDSL router can also be mounted on a wall. To mount the IDSL router, you will need: Three #6 pan-head screws with anchors (e.g., molly bolts, plastic or lead anchors)
Page 19 IDSL Router Hardware Template 5.43" Front (LEDs) 7.55" To Bottom Hole 98-16171...
Page 20: Idsl Router Technical Specifications
120 VAC (+10%), 60 Hz; or 230 VAC (+10%), 50/60 Hz Output: 18 VDC nominal at 0.8A Hotwire IDSL 6301: 5 watts (nominal) Hotwire IDSL 6302: 8 watts (nominal) Class B Subpart B digital device Refer to equipment's label for approvals on product.
Page 21: Important Safety Instructions
Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered.
Page 22: Declaration Of Conformity
Trade Name: Hotwire Model Numbers: 6301-A1-200 and 6302-A1-200 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 23: Warranty, Sales, Service, And Training Information
Warranty, Sales, Service, and Training Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods: Internet: Visit the Paradyne World Wide Web site at www.paradyne.com.
Page 24 " *6301-A2-GN10-10*...

This manual is also suitable for:

Hotwire 6302

Paradyne Hotwire 6301 Installation Instructions Manual

Quick Links

Hotwire 6301/6302 IDSL Routers Overview

Related Manuals for Paradyne Hotwire 6301

Summary of Contents for Paradyne Hotwire 6301

This manual is also suitable for:

Table of Contents