Contents 1 Safety 9 Additional information Charge your USB device 2 Your car audio system Reset the system Introduction Replace the fuse What's in the box Overview of the system 10 Product information 3 Install the car audio system 11 Troubleshooting Connect wires Mount into the dashboard 12 Notice...
1 Safety Read and understand all instructions before you use this device. If damage is caused by failure to follow instructions, the warranty does not apply. • Modification of the product could result in hazardous radiation of EMC or other unsafe operation.
What's in the box system Check and identify the contents of the package: Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. Introduction a Main unit (with a sleeve)
Overview of the system q p o n m l k j i h e AUDIO IN • Unlock the front panel. • Connect to the audio output socket (usually the headphone socket) of an external device. • Return to the previous menu. •...
Page 7
• Start, pause, or resume the play of • In radio mode, press to select the tracks. preset radio station of No. 1. • In radio mode, press to select the • In radio mode, press and hold to store preset radio station of No.
Page 8
u BAND • Press repeatedly to select a tuner band. v MENU • Press to access the system menu. • Insert an SD/SDHC card. x RESET • Press to reset the system to factory default settings.
3 Install the car Connect wires audio system Note • Make sure that all loose leads are insulated with electrical tape. Caution • Consult a professional to connect wires as instructed below. • Use the controls only as stated in this user manual. Check the car's wiring carefully and connect Always follow the instructions in this chapter in them to the the ISO male connectors.
Connect the antenna and amplifier as Make sure that the car dashboard opening illustrated, if applicable. is within these measurements: REAR Remove the mounting sleeve with the supplied disassembly tools. Sockets on rear External sockets or panel connectors For ISO male As indicated above connectors REAR L...
Slide the unit into the sleeve until you hear a "click". Press the left end of the front panel inwards until it is securely locked with a "click". Attach the trim plate. Detach the front panel Note • Before you insert an SD/SDHC card or reset the system, detach the front panel.
Rotate clockwise to set the minute. Press to turn on the system. » [PHILIPS] is displayed and then Display the clock [SELECT OPERATING REGION] (select a radio region) scrolls. /DISP until [CLK] and the set...
5 Listen to radio Mute the button beep The beep sound of buttons is enabled by default. Press MENU to access the system menu. Switch to radio mode repeatedly until [BEEP ON] Press or [BEEP OFF] is displayed. Press AS/SOURCE repeatedly to switch •...
[LOC OFF]: Search for radio stations • Store radio stations manually with strong and weak signals. Press /BAND repeatedly to select a band. Search for a radio station Tune to the radio station that you want to store. Press and hold Search for a radio station , or to store the radio station at the...
Page 15
Press to access the list of program Use alternate frequencies types. If the signal of an RDS station is poor, enable Rotate to select a program type, and the AF (Alternate Frequency) function to search then press to confirm. for another station that broadcasts the same Item Program Description...
6 Play from a Synchronize the system clock storage device You can synchronize the system clock with an RDS station that transmits time signals. Press MENU to access the system menu. repeatedly until [CT ON] or Press This system can play .mp3 files that are copied [CT OFF] is displayed.
Press AS/SOURCE repeatedly to switch Switch tracks the source. [USB]: For a USB storage device that • During play, you can switch tracks or folders is connected to the USB socket on the quickly. front panel [SD/SDHC]: For an SD/SDHC card •...
7 Listen to an 8 Adjust sound external player The following operations are applicable to all supported media. You can use the system to amplify the audio Button Function input from an external player, for example, MP3 Rotate to increase or decrease player.
9 Additional Replace the fuse information If there is no power, check the fuse and replace it if it is damaged. Check the electric connection. Remove the damaged fuse from the rear panel. Charge your USB device Insert a new fuse with the same specifications (15 A).
If the problem remains Power supply 12 V DC (11 V - 16 V), unsolved, go to the Philips Web page (www. negative ground philips.com/support). When you contact the Fuse 15 A...