Page 1 Granit™ XP 199xi Series Models: 1990iSR, 1990iXR, 1990iXLR, 1991iSR, 1991iXR, and 1991iXLR Industrial Area-Imaging Scanners and Bases User Guide...
Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. HII makes no representation or warranties regarding the information provided in the publication.
Page 3: Table Of Contents
TABLE OF CONTENTS Customer Support ........................xiii Technical Assistance ......................xiii Product Service and Repair ....................xiii Limited Warranty ........................xiii Chapter 1 - Get Started ..................1 About This Manual......................... 1 Unpack Your Device........................1 Features of the Device........................2 1990i/1991i SR Features.....................
Page 4 ACK/NAK Mode........................17 USBXNN............................17 ® Verifone Ruby Terminal......................18 ® Gilbarco Terminal........................18 Honeywell Bioptic Aux Port .....................18 ® Datalogic™ Magellan Aux Port....................19 Wincor Nixdorf Terminal ......................19 Wincor Nixdorf Beetle™ Terminal ..................19 Wincor Nixdorf RS232 Mode A....................20 Keyboard Country Layout......................20 Keyboard Wedge Modifiers......................27 ALT Mode ..........................27...
Page 5 Scanner-Bioptic ACK/NAK Mode..................37 Scanner-Bioptic ACK/NAK Timeout ................37 Chapter 3 - Cordless System Operation .............39 How the Cordless Charge Base Works.................39 Pair with a Honeywell Vehicle Mount Computer............39 Legacy Mode ...........................39 Compatibility Mode ......................40 Replace a Linked Scanner ......................40 Communication Between the Cordless System and the Host ........40 Program the Scanner and Base or Access Point .............41...
Page 6 About the Battery Status Icon ..................48 Reset Scanner ..........................49 Base Charge Modes........................49 Page ..............................50 Page Mode ..........................50 Page Pitch ..........................50 Error Indicators..........................51 Beeper Pitch - Base Error....................51 Number of Beeps - Base Error ..................51 Scanner Report..........................51 Scanner Address ..........................52 Base or Access Point Address ....................52 Scanner Modes..........................52 Charge Only Mode ........................52 Charge and Link Mode......................53...
Page 7 Batch Mode Transmit Delay ....................63 Multiple Scanner Operation ....................63 Scanner Name..........................64 Application Work Groups ......................65 Application Work Group Selection..................65 Reset the Factory Defaults: All Application Work Groups ..........66 Reset the Custom Defaults: All Application Work Groups ...........67 Use the Scanner with Bluetooth Devices................67 Bluetooth Secure Simple Pairing (SSP)................67 Connect with Bluetooth Device Directly...............68 Virtual Keyboard........................69...
Page 8 Vibrate – Good Read......................80 Beeper Pitch – Error ......................80 Beeper Duration – Good Read..................81 LED – Good Read ........................81 Number of Beeps – Good Read..................81 Number of Beeps – Error....................81 Good Read Delay ........................82 User-Specified Good Read Delay..................82 Trigger Modes ..........................83 Manual Trigger ........................83 Trigger Toggle .........................83 Serial Trigger ...........................85...
Page 9 End Character Activation After Good Read ..............95 Character Activation Timeout...................95 Character Deactivation......................95 Deactivation Character .......................96 Illumination Lights ........................96 Aimer Delay.............................96 User-Specified Aimer Delay....................97 Aimer Mode ............................97 Laser Aimer - Scan Duration ....................97 Centering............................98 Single Code Centering......................98 Custom Centering .........................98 Preferred Symbology .......................100 High Priority Symbology....................101 Low Priority Symbology ....................101 Preferred Symbology Time-out..................101...
Page 10 Example: Add a Tab Suffix to All Symbologies............114 Clear One or All Prefixes or Suffixes ................114 Add a Carriage Return Suffix to All Symbologies ..........115 Prefix Selections........................115 Suffix Selections........................115 Function Code Transmit......................116 Intercharacter, Interfunction, and Intermessage Delays.......... 116 Intercharacter Delay ......................
Page 11 Interleaved 2 of 5........................146 NEC 2 of 5 ............................148 Code 93 ............................149 Straight 2 of 5 Industrial (three-bar start/stop) ............151 Straight 2 of 5 IATA (two-bar start/stop) .................152 Matrix 2 of 5 ..........................153 Code 11 ............................154 Code 128 ............................155 ISBT 128 Concatenation....................155 GS1-128 ............................157 Telepen ............................158 UPC-A ............................159...
Page 12 GS1 Emulation........................... 184 TCIF Linked Code 39 (TLC39) ..................... 185 QR Code............................186 QR Code with Web Link....................188 DotCode............................188 Digimarc Barcode™ ........................189 Data Matrix..........................190 MaxiCode ............................. 192 Aztec Code ........................... 193 Chinese Sensible (Han Xin) Code ..................194 Postal Codes - 2D ........................
Page 13 Show Software Revision ......................223 Test Menu.............................223 TotalFreedom..........................224 Application Plug-Ins (Apps)....................224 EZConfig for Scanning Introduction .................225 Configure with EZConfig for Scanning..............225 Reset the Factory Defaults ....................226 Chapter 10 - Serial Programming Commands........227 Conventions ..........................227 Menu Command Syntax......................227 Query Commands ........................228 Trigger Commands........................230 Reset the Custom Defaults ....................231 Menu Commands ........................232 Chapter 11 - Product Specifications............261...
Page 14 Chapter 12 - Maintenance and Troubleshooting ........273 Repairs ............................273 Maintenance..........................273 Clean the Scanner......................273 Inspect Cords and Connectors ..................274 Replace Cables in Corded Scanners................274 Replace an Interface Cable .................... 274 Replace Cables and Batteries in Cordless Systems............ 274 Replace an Interface Cable in a Base.................
Page 15: Customer Support
Technical Support portal. For our latest contact information, see sps.honeywell.com. Product Service and Repair Honeywell International Inc. provides service for all of its products through service centers throughout the world. Go to sps.honeywell.com and select Support to find a service center near you or to get a Return Material Authorization number (RMA #) before returning a product.
Page 16 Granit XP User Guide...
Page 17: Chapter 1 - Get Started
Product specifications, dimensions, warranty, and cus- tomer support information are also included. Honeywell barcode scanners are factory programmed for the most common termi- nal and communications settings. If you need to change these settings, program- ming is accomplished by scanning the barcodes in this guide.
Page 18: Features Of The Device
Features of the Device 1990i/1991i SR Features Provides extreme performance scanning even on damaged and low-quality bar- codes. The SR is built to survive harsh treatment, including drops and extreme temperatures. Ideally suited to normal near-field scanning operations on 1D and 2D barcodes.
Page 19: Connect With Usb
Note: It is important to insert the red O-ring onto the end of the communication cable as shown, and make sure that the O-ring cannot be seen after the cable is inserted into the scanner. This ensures proper assembly and IP65/67 compliance function. Connect with USB A scanner or a cordless base can be connected to the USB port of a computer.
Page 20: Connect With Keyboard Wedge
CCB22-100BT-03N Base USB Connection: Note: The power supply must be ordered separately, if needed. 3. The scanner beeps. 4. Verify the scanner or cordless base operation by scanning a barcode from the Sample Symbols, beginning on page 289. The unit defaults to a USB PC Keyboard. Refer to page 16 for other USB terminal settings.
Page 21 1. Turn off power and disconnect the keyboard cable from the back of the termi- nal/computer. 2. Connect the appropriate interface cable to the device and to the terminal/ computer. Corded Granit XP Scanner Keyboard Wedge Connection: Note: The power supply must be ordered separately, if needed. CCB22-100BT-03N Base Keyboard Wedge Connection: 3.
Page 22: Connect With Rs232 Serial Port
Connect with RS232 Serial Port 1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the scanner. Note: For the scanner or cordless base to work properly, you must have the correct cable for your type of terminal/computer. Corded Granit XP Scanner RS232 Serial Port Connection: 3.
Page 23: Connect With Rs485
4. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the port. 5. Once the scanner or cordless base has been fully connected, power up the computer. This interface programs 115,200 baud, 8 data bits, no parity, and 1 stop bit. Connect with RS485 A Granit XP scanner can be connected for an IBM POS terminal interface.
Page 24: Reading Techniques
Reading Techniques The Granit XP SR scanners have an aimer that projects a bright red spot/cross and corner indicators that correspond to the scanner’s field of view. The aiming spot/ cross should be centered over the barcode, with the entire barcode falling within the corner indicators.
Page 25: Granit Xp Sr
Granit XP SR Linear Barcodes and 2D matrix symbol with aiming dot. Granit XP User Guide...
Page 26: Granit Xp Xr
Granit XP XLR Menu Barcode Security Settings Honeywell scanners are programmed by scanning menu barcodes or by sending serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Barcode Security settings. Contact the nearest tech-...
Page 27: Set Custom Defaults
Set Custom Defaults You have the ability to create a set of menu commands as your own, custom defaults. To do so, scan the Set Custom Defaults barcode below before scanning the menu commands for your custom defaults. If a menu command requires scan- ning numeric codes from the Programming Chart, beginning on page 291, then a...
Page 28: Reset The Custom Defaults
Reset the Custom Defaults If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults barcode below. This is the recommended default barcode for most users. It resets the scanner to the custom default settings. If there are no cus- tom defaults, it will reset the scanner to the factory default settings.
Page 29: Chapter 2 - Program The Interface
CHAPTER PROGRAM THE INTERFACE Introduction This chapter describes how to program your system for the desired interface. Program the Interface - Plug and Play Plug and Play barcodes provide instant scanner set up for commonly used inter- faces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.
Page 30: Laptop Direct Connect
Laptop Direct Connect For most laptops, scanning the Laptop Direct Connect barcode allows operation of the scanner in parallel with the integral keyboard. The following Laptop Direct Connect barcode also programs a carriage return (CR) suffix and turns on Emulate External Keyboard (page 29).
Page 31: Usb Ibm Surepos
IBM Port 17 Interface IBM Port 9B HHBCR-2 Interface Each barcode above also programs the following suffixes for each symbology: Symbology Suffix Symbology Suffix EAN 8 Code 39 00 0A 0B EAN 13 Interleaved 2 of 5 00 0D 0B UPC A Code 128 * 00 0A 0B...
Page 32: Usb Pc Or Macintosh Keyboard
No extra configuration (e.g., baud rate) is necessary. Note: If you scan the USB Serial barcode either with an older Honeywell serial driver, or no driver installed, you may no longer be able to scan barcodes. If this happens, either uninstall the older driver versions and install the latest driver, or delete the specific device entry in Device Manager.
Page 33: Cts/Rts Emulation
CTS/RTS Emulation CTS/RTS Emulation On * CTS/RTS Emulation Off ACK/NAK Mode ACK/NAK Mode On * ACK/NAK Mode Off USBXNN *Report PID as built Report PID as Granit 1910i Report PID as Granit 1980i Granit XP User Guide...
Page 34: Verifone ® Ruby Terminal
Gilbarco Settings Honeywell Bioptic Aux Port Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This barcode sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit.
Page 35: Datalogic™ Magellan ® Aux Port
® Datalogic™ Magellan Aux Port Scan the following Plug and Play code to program the scanner for a Datalogic Magellan auxiliary port configuration. This barcode sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit. Datalogic Magellan Settings Wincor Nixdorf Terminal Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf...
Page 36: Wincor Nixdorf Rs232 Mode A
Wincor Nixdorf RS232 Mode A Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf RS232 Mode A terminal. This barcode sets the baud rate to 9600 bps and the data format to 8 data bits, odd parity, 1 stop bit. The following prefixes are programmed for each symbology: Symbology Prefix...
Page 37 Keyboard Countries (Continued) Belarus Belgium Bosnia Brazil Brazil (MS) Bulgaria (Cyrillic) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) Croatia Czech Granit XP User Guide...
Page 38 Keyboard Countries (Continued) Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark Dutch (Netherlands) Estonia Faroese Finland France Gaelic Germany Greek Granit XP User Guide...
Page 39 Keyboard Countries (Continued) Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) Greek (Latin) Greek (MS) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Irish Granit XP User Guide...
Page 40 Keyboard Countries (Continued) Italian (142) Italy Japan ASCII Kazakh Kyrgyz (Cyrillic) Latin America Latvia Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Granit XP User Guide...
Page 41 Keyboard Countries (Continued) Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Romania Russia Russian (MS) Russian (Typewriter) Serbia (Cyrillic) Granit XP User Guide...
Page 42 Keyboard Countries (Continued) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) Switzerland (German) Tatar Turkey F Granit XP User Guide...
Page 43: Keyboard Wedge Modifiers
Keyboard Countries (Continued) Turkey Q Ukrainian United Kingdom United States (Dvorak) United States (Dvorak left) United States (Dvorak right) United States (International) Uzbek (Cyrillic) Keyboard Wedge Modifiers ALT Mode If your barcode contains special characters from the extended ASCII chart, for example, an e with an accent grave (è), you will use ALT Mode.
Page 44: Keyboard Style
If your keystrokes require the ALT key and 3 or 4 characters, scan the 3 Characters or 4 Characters barcode. The data is then output with the special character(s) for values 00-255. Default = Off. * Off 3 Characters 4 Characters Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock.
Page 45: Keyboard Conversion
* Europe China Automatic Caps Lock is used if you change the Caps Lock key on and off. The soft- ware tracks and reflects if you have Caps Lock on or off. This selection can only be used with systems that have an LED that notes the Caps Lock status (AT key- boards).
Page 46: Control Character Output
Default = Keyboard Conversion Off. * Keyboard Conversion Off Convert All Characters to Upper Case Convert All Characters to Lower Case Control Character Output This selection sends a text string instead of a control character. For example, when the control character for a carriage return is expected, the output would display [CR] instead of the ASCII code of 0D.
Page 47 Windows Mode Prefix/Suffix Off: The scanner sends key combinations for ASCII control characters for values 00-1F, but it does not translate prefix or suffix infor- mation. Support ALT 3 Digit HEX Mode: The scanner sends key combinations for ASCII control characters for values 00-1F transmitted as the ALT key and 3 digits. Default = Control + X Mode Off.
Page 48: Rs232 Modifiers
Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off. Numeric Keypad Mode On * Numeric Keypad Mode Off Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters.
Page 49: Rs232 Word Length: Data Bits, Stop Bits, And Parity
2,400 4,800 9,600 19,200 38,400 57,600 * 115,200 RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctua- tion), select 7 data bits.
Page 50: Rs232 Receiver Time-Out
7 Data, 1 Stop, Parity Odd 7 Data, 2 Stop, Parity Even 7 Data, 2 Stop, Parity None 7 Data, 2 Stop, Parity Odd 8 Data, 1 Stop, Parity Even * 8 Data, 1 Stop, Parity None 8 Data, 1 Stop, Parity Odd 8 Data, 1 Stop, Parity Mark RS232 Receiver Time-Out The unit stays awake to receive data until the RS232 Receiver Time-Out expires.
Page 51: Rs232 Handshake
RS232 Handshake RS232 Handshaking allows control of data transmission from the scanner using software commands from the host device. When RTS/CTS is turned Off, no data flow control is used. Flow Control, No Timeout: The scanner asserts RTS when it has data to send, and will wait indefinitely for CTS to be asserted by the host.
Page 52: Xon/Xoff
* ACK/NAK Off Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scan- ners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner.
Page 53: Scanner-Bioptic Packet Mode
Scanner-Bioptic Packet Mode Packet Mode On must be scanned to set the scanner’s format so it is compatible with a bioptic scanner. Default = Packet Mode Off. * Packet Mode Off Packet Mode On Scanner-Bioptic ACK/NAK Mode Bioptic ACK/NAK On must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each packet is sent.
Page 54 Granit XP User Guide...
Page 55: Chapter 3 - Cordless System Operation
Pair with a Honeywell Vehicle Mount Computer A Granit XP SR, Granit XP XR, or Granit XP XLR can pair with Honeywell vehicle mounted computers. Scan the EZPairing barcode that is either supplied with the vehicle mount computer, attached to the vehicle mount computer, or displayed on the screen.
Page 56: Compatibility Mode
Compatibility Mode In Compatibility Mode, the scanner can work with HID, SPP, or other Bluetooth profiles. Bluetooth needs to be set manually before scanning this barcode. Compatibility Mode (optional) Replace a Linked Scanner If you need to replace a broken or lost scanner that is linked to a base or an Access Point, scan the Override Locked Scanner barcode below with a new scanner and place that scanner in the base, or scan the Access Point linking barcode.
Page 57: Program The Scanner And Base Or Access Point
When data is scanned, the data is sent to the host system via the base or Access Point. The cordless scanner recognizes data acknowledgment (ACK) from the base or Access Point. If it cannot be determined that the data has been properly sent to the base or Access Point, the scanner issues an error indication.
Page 58: System Conditions
noisy RF environments. The bases (Bluetooth Class 1 or Class 2) provide a commu- nication range of 328 feet (100m) or 33 feet (10m) between the scanner and base or Access Point, depending on the environment. See Flexible Power Management, page 57, for information about controlling this range. System Conditions The components of the cordless system interact in specific ways as you associate a scanner to a base or Access Point, as you move a scanner out of range, bring a...
Page 59: Page Button
Page Button When you press the page button on the base or Access Point, the scanners associ- ated with that base or Access Point will begin beeping (3 short and 1 long beep). If you press the trigger on a scanner that is beeping in response, or press the page button on the base or Access Point a second time, all associated scanners will stop beeping.
Page 60: Charge Information
Replace it after the battery is unable to hold an adequate charge. • If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection. Refer to Customer Support on page xiii for additional information.
Page 61: Safety Precautions For Lithium Batteries
Safety Precautions for Lithium Batteries • Do not place batteries in fire or heat the batteries. • Do not store batteries near fire or other high temperature locations. • Do not store or carry batteries together with metal objects. • Do not expose batteries to water or allow the batteries to get wet.
Page 62 Querying battery volume by three times trigger in 2 seconds when the scanner is out of the base will activate the battery status icon. Note: This functionality is only available with the smart battery pack. Battery Icon Scanner Charge Yellow Green Beep Level...
Page 63: Base/Access Point Communication And Scanning
Base/Access Point Communication and Scanning The following feedback is provided by the base (red LED) or Access Point (blue LED) and indicates communication and scanning status. Communication Condition USB suspend On continuously Power on, system idle Short blinks in multiple pulses. Occurs while Receiving data transferring data to/from the RF module or the Host port.
Page 64: About The Bluetooth Status And Battery Icons
About the Bluetooth Status and Battery Icons Battery Status Icon: Bluetooth Status Icon About the Bluetooth Status Icon The blue Bluetooth Icon LED has two behaviors flash and on. The icon will flash when linking to a device then will remain on, indicating the base and scanner are linked and stays on when the scanner is in base.
Page 65: Reset Scanner
Scanner LED Scanner Beep Charge Level Red 3 sets of flashes, repeatedly No Beep <5% every 3 seconds Red 20 sets of rapid flashes No Beep <2% Reset Scanner Scanning this barcode reboots the scanner and causes it to relink with the base or Access Point.
Page 66: Page Mode
External Power Only Page Page Mode By default, the page button on the base or Access Point pages the scanners associ- ated with that base or Access Point. If you want the page button on your base or Access Point to be disabled, scan the Page Mode Off barcode, below. When Page Mode is off, the base or Access Point will no longer page scanners when the button is pressed.
Page 67: Error Indicators
Error Indicators Beeper Pitch - Base Error The base can be configured to beep at a particular pitch when an error occurs, such as transmission problems to a host system. The beeper pitch codes modify the pitch (frequency) of the error tone the base emits when there is an error. Default = Low.
Page 68: Scanner Address
Scanner Address Scan the barcode below to determine the address of the scanner you are using. Scanner Address Base or Access Point Address Scan the barcode below to determine the address of the base or Access Point you are using. Base Address Scanner Modes Your scanner is capable of working in single scanner mode, multiple scanner...
Page 69: Charge And Link Mode
Charge and Link Mode If you want to charge a scanner and link to the base, use Charge and Link Mode. If the base is programmed for Charge Only Mode, you must link a scanner to it first in order to program it for Charge and Link Mode. Scan the linking barcode on the base to link the scanner, then scan Charge and Link Mode.
Page 70: Unlink The Scanner
Unlink the Scanner If a base or an Access Point has a scanner linked to it, that scanner must be unlinked before a new scanner can be linked. Once the previous scanner is unlinked, it will no longer communicate with the base or Access Point. To unlink the scanner from a base or an Access Point, scan the Unlink Scanner barcode below.
Page 71: Alarm Sound Type
base and to set the alarm duration, scan the appropriate barcode below and then set the time-out duration (from 0-3000 seconds) by scanning digits on the Programming Chart, beginning on page 291, then Save. Default = 0 sec (no alarm). Base Alarm Duration Note: The Access Point does not have a base alarm.
Page 72: Scanner Power Time-Out Timer
Scanner Power Time-Out Timer When there is no activity within a specified time period, the scanner enters low power mode. Scan the appropriate scanner power time-out barcode to change the time-out duration (in seconds). Note: Scanning zero (0) is the equivalent of setting no time-out. If there are no trigger pulls during the timer interval, the scanner goes into power down mode.
Page 73: Flexible Power Management
Flexible Power Management If you are experiencing network performance issues, and suspect the scanner is interfering with other devices, you can turn down the power output of the scanner. This reduces the range between the scanner and a base or an Access Point as shown in the following illustration: Scanner 802.11...
Page 74: Batch Mode
Access Point once the scanner is back in range or when the records are manually transmitted. Note: Batch Mode is only supported by the Honeywell Charge and Communication Base (CCB) and Honeywell Access Point (AP). Batch mode has limitations when using multiple scanners to one base or Access Point.
Page 75: Batch Mode Beep
Batch Mode Beep When scanning in Inventory Batch Mode (page 58), the scanner beeps every time a barcode is scanned. When Batch Mode Beep is On, you will also hear a click when each barcode is sent to the host. If you do not want to hear these clicks, scan Batch Mode Beep Off.
Page 76: Batch Mode Quantity
Batch Mode Quantity When in Batch Mode, you may wish to transmit the number of multiple barcodes scanned, rather than a single barcode multiple times. For example, if you scan three barcodes called XYZ with Batch Mode Quantity Off, when you transmit your data it will appear as XYZ three times.
Page 77 1. Scan the quantity 0 barcode to change the quantity to 1030. 2. Scan the quantity 0 barcode to change the quantity to 0300. 3. Scan the quantity 1 barcode to change the quantity to 3001. 4. Scan the quantity 0 barcode to change the quantity to 0010. Default = 1.
Page 78: Batch Mode Output Order
Batch Mode Output Order When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-out). Default = Batch Mode FIFO. * Batch Mode FIFO Batch Mode LIFO Total Records If you wish to output the total number of barcodes scanned when in Batch Mode, scan Total Records.
Page 79: Transmit Records To Host
Transmit Records to Host If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 58), you must scan the following barcode to transmit all the stored data to the host system. Transmit Inventory Records Batch Mode Transmit Delay Sometimes when accumulated scans are sent to the host system, the transmission of those scans is too fast for the application to process.
Page 80: Scanner Name
To put the scanner in multiple scanner mode, scan the barcode below. Once you scan this barcode, the scanner is unlinked from the base or Access Point and must either be placed into the base, or you must scan the Access Point linking barcode in order to relink.
Page 81: Application Work Groups
You could assign all the scanners in the retail area to one work group and those in the warehouse to another. Consequently, any desired changes to either the retail or warehouse area would apply to all scanners in that particular work group. Honeywell’s online configuration tool, EZConfig-Scanning (page 224), makes it easy for you to program your system for use with multiple scanners and multiple work groups.
Page 82: Reset The Factory Defaults: All Application Work Groups
Group 1 Group 2 Reset the Factory Defaults: All Application Work Groups The following barcode defaults all of the work groups to the factory default settings. PAPDFT& Factory Default Settings: All Work Groups To see what the factory default settings are, refer to the table of Menu Commands, beginning on page 232.
Page 83: Reset The Custom Defaults: All Application Work Groups
Use the Scanner with Bluetooth Devices The scanner can be used either with the charge base or with other Bluetooth devices. Those devices include personal computers, laptops, PDAs, and Honeywell mobility systems devices. Bluetooth Secure Simple Pairing (SSP) Secure Simple Pairing (SSP) allows you to connect simply and securely to other...
Page 84: Connect With Bluetooth Device Directly
Connect with Bluetooth Device Directly Your scanner can be paired with Bluetooth-capable devices, such as personal com- puters, laptops, and tablets, so that scanned data appears on your device screen as though it was entered on the keyboard. In order to pair with the Bluetooth device: 1.
Page 85: Virtual Keyboard
Save Virtual Keyboard Once your scanner has been connected directly to an iPad, smart phone, or laptop, you can toggle the virtual keyboard on your device with a quick double pull of the scanner trigger. Default = Enable. Disable * Enable Granit XP User Guide...
Page 86: Bluetooth Hid Keyboard Disconnect
Non-Base BT Connection PDAs/Mobility Systems Devices You may also use the scanner with a PDA or a Honeywell Mobility Systems device. Scan the barcode below and follow the instructions supplied with your Bluetooth device to locate the scanner, and connect with it.
Page 87: Minimize Bluetooth/Ism Band Network Activity
Minimize Bluetooth/ISM Band Network Activity The settings described below can help you customize the relinking behavior of the cordless area-imaging system to obtain the best compromise between conve- nience and low interference. Note: ISM band refers to the 2.4 to 2.48 GHz frequency band used by wireless networks, cordless phones, and Bluetooth.
Page 88: Maximum Link Attempts
Event Auto Reconnect On Auto Reconnect Off Scanner placed in different Relink to new base occurs automatically. base unit Maximum Link Attempts The Maximum Link Attempts setting controls the number of times the scanner tries to form a connection with a base or an Access Point. During the connection setup process, the scanner transmits in order to search for and connect to a base or an Access Point.
Page 89: Bluetooth/Ism Network Activity Examples
Bluetooth/ISM Network Activity Examples Default values When the scanner goes out of range, the scanner repeatedly attempts to connect to the base unit or Access Point. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After one hour, the scanner pow- ers off and batch mode data is lost.
Page 90 feedback to the scan operator. The Host ACK functionality is controlled via a num- ber of pre-defined escape commands that are sent to the scanner to make it behave in different ways. Note: System performance degrades when using Host ACK at rates lower than 9600 baud. The following criteria must be met for the Host ACK to work correctly: •...
Page 91: Host Ack On/Off
• Scanner operation is suspended until 1) a valid escape string is received from the host system or 2) the scanner times out. • Once condition 1 or 2 above has been met, the scanner is ready to scan again, and the process repeats.
Page 92 Command Action [ESC] 7, Beeps to indicate a successful decode and communication to host. [ESC] 8,[ESC] 8, Razz or error tone to indicate a decode/communication to host was unsuccessful. Granit XP User Guide...
Page 93: Chapter 4 - Input/Output Settings
CHAPTER INPUT/OUTPUT SETTINGS Power Up Beeper The scanner can be programmed to beep when it’s powered up. If you are using a cordless system, the base can also be programmed to beep when it is powered up. Scan the Off barcode(s) if you don’t want a power up beep. Default = Power Up Beeper On - Scanner.
Page 94: Beep On Bel Character
Beep on BEL Character You may wish to force the scanner to beep upon a command sent from the host. If you scan the Beep on BEL On barcode below, the scanner will beep every time a BEL character is received from the host. Default = Beep on BEL Off. *Beep on BEL Off Beep on BEL On Trigger Click...
Page 95: Beeper Volume - Good Read
Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High. Medium * High Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read.
Page 96: Vibrate - Good Read
Vibrate – Good Read The scanner vibrates once when a barcode is successfully read, and twice when a programming barcode is successfully read. When a programming barcode is unsuccessful, the scanner emits one long vibration (2 times the Vibrate Duration length).
Page 97: Beeper Duration - Good Read
Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal. * Normal Beep Short Beep Short Beep LED – Good Read The LED indicator can be programmed On or Off in response to a good read. Default = On.
Page 98: Good Read Delay
to an error. To change the number of error beeps, scan the barcode below and then scan a digit (1-9) barcode from the Programming Chart, beginning on page 291, then Save. Default = 1. Number of Error Beeps/LED Flashes Good Read Delay This sets the minimum amount of time before the scanner can read another bar- code.
Page 99: Trigger Modes
Trigger Modes Manual Trigger When in manual trigger mode, the scanner scans until a barcode is read, or until the trigger is released. Two modes are available, Normal and Enhanced. Normal mode offers good scan speed and the longest working ranges (depth of field). Enhanced mode will give you the highest possible scan speed but slightly less range than Normal mode.
Page 100 Trigger Number This sets the number of trigger presses required to activate the Trigger Toggle Mode. Default = 3. 2 Quick Triggers *3 Quick Triggers 4 Quick Triggers Trigger Timing This sets the timing of the trigger presses in order to qualify as a trigger toggle, rather than a regular trigger press.
Page 101: Serial Trigger
Serial Trigger You can activate the scanner either by pressing the trigger, or using a serial trigger command (see Trigger Commands on page 230). You must be in a serial interface mode in order to use serial triggering. Refer to RS232 Serial Port (page 14) or Serial...
Page 102: Presentation Mode
Presentation Mode Presentation Mode uses ambient light and scanner illumination to detect bar- codes. When in Presentation Mode, the LEDs remain dim until a barcode is pre- sented to the scanner, then the aimer turns on and the LEDs turn up to read the code.
Page 103: Presentation Centering
Presentation Centering Use Presentation Centering to narrow the scanner’s field of view when it is in the stand to make sure the scanner reads only those barcodes intended by the user. For instance, if multiple codes are placed closely together, Presentation Centering will insure that only the desired codes are read.
Page 104: Near-Far Camera Modes (Xr & Xlr Models Only)
Scan Presentation Centering On, then scan one of the following barcodes to change the top, bottom, left, or right of the centering window. Then scan the per- cent you want to shift the centering window from the Programming Chart, begin- ning on page 291, then Save.
Page 105: Camera Sensors
Near Camera Only Far Camera Only * Automatic Switching Alternate Switching Camera Sensors The far camera has various depth positions. If you need to adjust the position, scan the appropriate barcode below. Default = All Positions. Far Position Medium Position Near Position * All Positions Camera Illumination...
Page 106: Poor Quality Codes
* Fixed Illumination Near Camera * Far Camera In Alternate Illumination the illumination alternates between near and far. Alternate Illumination In Automatic Illumination, the illumination will automatically switch to far illumi- nation when images are too dark. Automatic Illumination Poor Quality Codes Poor Quality 1D Codes This setting improves the scanner’s ability to read damaged or badly printed linear barcodes.
Page 107: Poor Quality Pdf Codes
Poor Quality PDF Codes This setting improves the scanner’s ability to read damaged or badly printed PDF codes by combining information from multiple images. It is useful when a com- plete barcode cannot be seen in one image. This setting does not affect 1D bar- code reading.
Page 108: Streaming Presentation™ Mode
CodeGate On Streaming Presentation™ Mode When in Streaming Presentation mode, the scanner’s aimer goes out after a short time, but the scan illumination remains on all the time to continuously search for barcodes. Two modes are available, Normal and Enhanced. Normal mode offers good scan speed and the longest working ranges (depth of field).
Page 109: Reread Delay
Reread Delay This sets the time period before the scanner can read the same barcode a second time. Setting a reread delay protects against accidental rereads of the same bar- code. Longer delays are effective in minimizing accidental rereads. Use shorter delays in applications where repetitive barcode scanning is required.
Page 110: Character Activation
Short (1000ms) Medium (2000ms) Long (3000ms) Extra Long (4000ms) Character Activation You may use a character sent from the host to trigger the scanner to begin scan- ning. When the activation character is received, the scanner continues scanning until either the Character Activation Timeout (page 95) is reached, the deactivation character is received (see...
Page 111: End Character Activation After Good Read
End Character Activation After Good Read After a barcode is successfully detected and read from the scanner, the illumina- tion can be programmed either to remain on and scanning, or to turn off. When End Character Activation After Good Read is enabled, the illumination turns off and stops scanning after a good read.
Page 112: Deactivation Character
Deactivation Character This sets the character used to terminate scanning when using Character Deacti- vation Mode. On the ASCII Conversion Chart (Code Page 1252), page 282, find the hex value that represents the character you want to use to terminate scanning. Scan the following barcode, then use the Programming Chart, beginning on page...
Page 113: User-Specified Aimer Delay
500 milliseconds * Off (no delay) User-Specified Aimer Delay If you want to set your own length for the duration of the delay, scan the barcode below, then set the time-out by scanning digits (0 - 4,000 ms) from the Programming Chart, beginning on page 291, then Save.
Page 114: Centering
Laser-Aimer Scan Duration Centering Use Centering to narrow the scanner’s field of view to make sure that when the scanner is hand-held, it reads only those barcodes intended by the user. For instance, if multiple codes are placed closely together, centering will insure that only the desired codes are read.
Page 115 Example: In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top, and 25% bottom. Since Barcode 1 passes through the centering window, it will be read. Barcode 2 does not pass through the centering window, so it will not be read.
Page 116: Preferred Symbology
Bottom of Centering Window Left of Centering Window Right of Centering Window Preferred Symbology The scanner can be programmed to specify one symbology as a higher priority over other symbologies in situations where both barcode symbologies appear on the same label, but the lower priority symbology cannot be disabled. For example, you may be using the scanner in a retail setting to read U.P.C.
Page 117: High Priority Symbology
High Priority Symbology To specify the high priority symbology, scan the High Priority Symbology barcode below. On the Symbology Charts on page 279, find the symbology you want to set as high priority. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart, beginning on page 291, then Save.
Page 118: Output Sequence Overview
Output Sequence Overview Output Sequence Editor This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in whatever order your application requires, regardless of the order in which the barcodes are scanned. You can define up to 15 barcodes in an output sequence.
Page 119: Output Sequence Editor Commands
5. End Output Sequence Editor Use FF to terminate this string or to begin another output sequence. If you are using barcodes, scan F F. Scan Save to save your entries. Other Programming Selections If you are creating an output sequence using barcodes, scan Discard (page 292) to exit without saving any output sequence changes.
Page 120 code identifier for Code 39 9999 code length that must match for Code 39, 9999 = all lengths start character match for Code 39, 43h = "C" termination string for first code code identifier for Code 128 9999 code length that must match for Code 128, 9999 = all lengths start character match for Code 128, 54h = “T”...
Page 121: Enter Output Sequence
start character match for Code 39, 43h = "C" termination string for first code code identifier for Code 128 9999 code length that must match for Code 128, 9999 = all lengths start character match for Code 128, 54h = “T” termination string for first code code identifier for PDF417 9999...
Page 122: Partial Sequence
Enter Output Sequence Partial Sequence If an output sequence operation is terminated before all your output sequence cri- teria are met, the barcode data acquired to that point is a “partial sequence.” You can define how partial sequences are output using the same types of command strings you used to create output sequences.
Page 123 9999 code length that must match for PDF417, 9999 = all lengths start character match for PDF417, 4Dh = “M” termination string for third code SEQSEP99 separator for each sequence, 99 = all symbologies left bracket (<) right bracket (>) SEQSUF99 separator for suffixes, 99 = all symbologies carriage return...
Page 124 Discard Partial Output Sequence If you want to discard partial sequences when the output sequence operation is terminated before completion, scan Discard Partial Sequence. * Discard Partial Sequence Output Sequence Timeouts You can set a timeout for every code in the output sequence defined by the SEQBLK command.
Page 125 Satisfactory Subset of Full Sequence Timeout Example To specify a subset, list its members using the SEQSAT command and terminate each subset with FF. The members of each subset are specified as single hex digits corresponding to their index within the full sequence, 1 being the first. For exam- ple, to specify two subsets, the first consisting of the first and second code in the sequence and the second subset consisting of the second and third code, use the command SEQSAT12FF23FF.
Page 126: Good Read Tone - Output Sequences
Good Read Tone - Output Sequences The scanner may be programmed to either beep or click in response to a good read of each barcode in an output sequence, or to emit a beep or error tone for a partial sequence.
Page 127: No Read
No Read With No Read turned On, the scanner notifies you if a code cannot be read. If using an EZConfig-Scanning Tool Scan Data Window (see page 225), an “NR” appears when a code cannot be read. If No Read is turned Off, the “NR” will not appear. Default = Off.
Page 128: Working Orientation
* Video Reverse Off Working Orientation Some barcodes are direction-sensitive. For example, KIX codes and OCR can mis- read when scanned sideways or upside down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scan- ner.
Page 129: Chapter 5 - Data Edit
CHAPTER DATA EDIT Prefix/Suffix Overview When a barcode is scanned, additional information is sent to the host computer along with the barcode data. This group of barcode data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.
Page 130: Add A Prefix Or Suffix
• When setting up for specific symbologies (as opposed to all symbologies), the specific symbology ID value counts as an added prefix or suffix character. • The maximum size of a prefix or suffix configuration is 200 characters, which includes header information. Add a Prefix or Suffix: Step 1.
Page 131: Add A Carriage Return Suffix To All Symbologies
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit hex value from the Symbology Chart (included in Symbology Charts, beginning on page 279) for the symbology from which you want to clear the prefix or suffix. Step 3.
Page 132: Function Code Transmit
Clear All Suffixes Function Code Transmit By default, all ASCII control characters are transmitted with barcode data. These non-printable characters are translated into predefined key strokes, or CTRL+X functions (see ASCII Conversion Chart (Code Page 1252), beginning on page 282). If these key strokes interfere with your host’s software application, scan Disable to keep these ASCII control characters from being transmitted.
Page 133: User Specified Intercharacter Delay
To remove this delay, scan the Intercharacter Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 291. Note: Intercharacter delays are not supported in USB serial emulation. User Specified Intercharacter Delay An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed after the transmission of a particular character of scanned data.
Page 134: Intermessage Delay
To remove this delay, scan the Interfunction Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 291. Intermessage Delay An intermessage delay of up to 5000 milliseconds (in 5ms increments) may be placed between each scan transmission.
Page 135: Chapter 6 - Data Format
CHAPTER DATA FORMAT Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar- code data as it is scanned. The selections in the following pages are used only if you wish to alter the output.
Page 136: Show Data Format
If you have changed data format settings, and wish to clear all formats and return to the factory defaults, scan the Default Data Format code below. * Default Data Format Show Data Format Scan the barcode below to show current data format settings. Data Format Settings Add a Data Format Step 1.
Page 137: Other Programming Selections
Chart, beginning on page 291. For example, 50 characters is entered as 0050. Note: 9999 indicates all lengths. Step 6. Editor Commands Refer to Data Format Editor Commands (page 122). Scan the symbols that represent the command you want to enter. Step 7.
Page 138: Terminal Id Table
Save Discard Terminal ID Table Terminal Model(s) Terminal ID PC keyboard (HID) Mac Keyboard PC Keyboard (Japanese) Serial (COM driver required) HID POS USB SurePOS Handheld USB SurePOS Tabletop Serial RS232 TTL RS232 True RS485 (IBM-HHBCR 1+2, 46xx) Keyboard PS2 compatibles AT compatibles Data Format Editor Commands When working with the Data Format Editor, a virtual cursor is moved along your...
Page 139 Send a number of characters F2 Include in the output message a number of characters followed by an insert character. Start from the current cursor position and continue for “nn” characters or through the last character in the input message, followed by character “xx.” Syntax = F2nnxx where nn stands for the numeric value (00-99) for the number of characters, and xx stands for the insert character’s hex value for its ASCII code.
Page 140 Send all characters up to a particular character F3 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search character “ss,” followed by an insert character. The cursor is moved forward to the “ss”...
Page 141 42 is the hex value for B The data is output as: 1234567890 Send all but the last characters E9 Include in the output message all but the last “nn” characters, starting from the current cursor position. The cursor is moved forward to one position past the last input message character included.
Page 142 1234567890**ABCDEFGHIJ <CR> Insert symbology name B3 Insert the name of the barcode symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Charts on page 279). Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
Page 143 B3 is the “Insert symbology name” command F4 is the “Insert a character multiple times” command 20 is the hex value for a space 01 is the number of times the space character is sent B4 is the “Insert barcode length” command F4 is the “Insert a character multiple times”...
Page 144: Move Commands
Move Commands Move the cursor forward a number of characters F5 Move the cursor ahead “nn” characters from current cursor position. Syntax = F5nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved ahead. F5 Example: Move the cursor forward and send the data Move the cursor forward 3 characters, then send the rest of the barcode data from the barcode above.
Page 145: Search Commands
F7 is the “Move the cursor to the beginning” command F2 is the “Send a number of characters” command 06 is the number of characters to send 0D is the hex value for a CR The data is output as: 123456 <CR>...
Page 146 Search backward for a character F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F9xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for...
Page 147 Search backward for a string B1 Search backward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B1nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B1000454657374 will search backward for the first occurrence of the 4 character string “Test.”...
Page 148: Miscellaneous Commands
Miscellaneous Commands Suppress characters FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced by other commands. When the FC command is encountered, the suppress function is terminated. The cursor is not moved by the FB command.
Page 149 If the barcode has characters that the host application does not want included, you can use the E4 command to replace those characters with something else. In this example, you will replace the zeros in the barcode above with carriage returns. Command string: E402300DF10D E4 is the “Replace characters”...
Page 150 EC Example: Only output the data if the barcode begins with a number If you want only data from barcodes that begin with a number, you can use EC to check for the number. Command string: ECF10D EC is the “Check for a number” command F1 is the “Send all characters”...
Page 151: Data Formatter
Insert a delay EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. Syntax = EFnnnn where nnnn stands for the delay in 5ms increments, up to 9999. This command can only be used with keyboard emulation. Discard Data B8 Discards types of data.
Page 152: Data Format Non-Match Error Tone
requirements generates an error tone and the data in that barcode is not transmitted. If you wish to process this type of barcode without generating an error tone, see Data Format Non-Match Error Tone. • Data Format Required, Drop Prefix/Suffix Scanned data is modified according to your data format.
Page 153: Primary/Alternate Data Formats
Data Format Non-Match Error Tone Off Primary/Alternate Data Formats You can save up to four data formats, and switch between these formats. Your pri- mary data format is saved under 0. Your other three formats are saved under 1, 2, and 3.
Page 154 Single Scan-Data Format 1 Single Scan-Data Format 2 Single Scan-Data Format 3 Granit XP User Guide...
Page 155: Chapter 7 - Symbologies
CHAPTER SYMBOLOGIES This programming section contains the following menu selections. Refer to Chapter 10 for settings and defaults. • All Symbologies • Interleaved 2 of 5 • Aztec Code • Korea Post • China Post (Hong Kong 2 of 5) •...
Page 156: All Symbologies
All Symbologies For best scanner performance, you should only enable the symbologies that you need. Scan All Symbologies Off to disable all symbologies, then enable the sym- bologies you need by scanning the On barcode for each symbology. All Symbologies Off Message Length Description You are able to set the valid reading length of some of the barcode symbologies.
Page 157 Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the barcode. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Trans- mit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar barcodes with Modulo 16 check characters.
Page 158 Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concate- nated into one with the “D” characters omitted. A 1 2 3 4 D D 5 6 7 8 A Select Require to prevent the scanner from decoding a single “D”...
Page 159: Code 39
Code 39 < Default All Code 39 Settings > Code 39 On/Off * On If you are reading Code 39 barcodes, Codablock A should remain disabled. If you are enabling Codablock A (see Codablock A on page 179), you should disable Code Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the barcode.
Page 160 When Check Character is set to Validate and Transmit, the scanner only reads Code 39 barcodes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character. * No Check Character Validate, but Don’t Transmit Validate and Transmit Code 39 Message Length...
Page 161 Code 32 Pharmaceutical (PARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian phar- macies. This symbology is also known as PARAF. Default = Off. Note: Trioptic Code (page 179) must be turned off while scanning Code 32 Pharmaceutical codes.
Page 162: Interleaved 2 Of 5
* Full ASCII Off Code 39 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar- code being scanned was created using a code page that is different from the one the host program is expecting.
Page 163 When Check Digit is set to Validate and Transmit, the scanner only reads Inter- leaved 2 of 5 barcodes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit...
Page 164: Nec 2 Of 5
NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of 5 On/Off * On Check Digit No Check Digit indicates that the scanner reads and transmits barcode data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 barcodes printed with a check digit, but will not transmit the check digit with the scanned data.
Page 165: Code 93
NEC 2 of 5 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93 <...
Page 166 Code 93 Append This function allows the scanner to append the data from several Code 93 bar- codes together before transmitting them to the host computer. When this function is enabled, the scanner stores those Code 93 barcodes that start with a space (excluding the start and stop symbols), and does not immediately transmit the data.
Page 167: Straight 2 Of 5 Industrial (Three-Bar Start/Stop)
Straight 2 of 5 Industrial (three-bar start/stop) <Default All Straight 2 of 5 Industrial Settings> Straight 2 of 5 Industrial On/Off * Off Straight 2 of 5 Industrial Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information.
Page 168: Straight 2 Of 5 Iata (Two-Bar Start/Stop)
Straight 2 of 5 IATA (two-bar start/stop) <Default All Straight 2 of 5 IATA Settings> Straight 2 of 5 IATA On/Off * Off Straight 2 of 5 IATA Redundancy If you are encountering errors when reading Straight 2 of 5 IATA barcodes, you may want to adjust the redundancy count.
Page 169: Matrix 2 Of 5
Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Matrix 2 of 5 On/Off * Off Matrix 2 of 5 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-80.
Page 170: Code 11
Code 11 <Default All Code 11 Settings> Code 11 On/Off * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 barcodes. Default = Two Check Digits. One Check Digit * Two Check Digits Code 11 Message Length Scan the barcodes below to change the message length.
Page 171: Code 128
Code 128 <Default All Code 128 Settings> Code 128 On/Off * On If you are reading Code 128 barcodes, Codablock F should remain disabled. If you are enabling Codablock F (see Codablock F on page 180), you should disable Code 128.
Page 172 the higher the redundancy count, the longer it will take to decode the barcode. To adjust the redundancy, scan the Code 128 Redundancy barcode below, then scan a redundancy count between 0 and 10 on the Programming Chart, beginning on page 291.
Page 173: Gs1-128
Replacements on page 286), and scan the value and the Save barcode from the Programming Chart, beginning on page 291. The data characters should then appear properly. Code 128 Code Page GS1-128 <Default All GS1-128 Settings> GS1-128 On/Off * On GS1-128 Message Length Scan the barcodes below to change the message length.
Page 174: Telepen
Telepen <Default All Telepen Settings> Telepen On/Off * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pat- tern 2).
Page 175: Upc-A
Maximum Message Length UPC-A <Default All UPC-A Settings> UPC-A On/Off * On Note: To convert UPC-A barcodes to EAN-13, see Convert UPC-A to EAN-13 on page 166. UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.
Page 176 UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the begin- ning of the scanned data, but can be programmed so it is not transmitted (Off). Default = On. * On UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data. Default = Off for both 2 Digit and 5 Digit Addenda.
Page 177: Upc-A/Ean-13 With Extended Coupon Code
* Not Required Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A Addenda Required.
Page 178: Coupon Gs1 Databar Output
If you scan the Require Concatenation code, the scanner must see and read the coupon code and extended coupon code in a single read to transmit the data. No data is output unless both codes are read. Default = Off. * Off Allow Concatenation Require Concatenation...
Page 179: Upc-E0
UPC-E0 <Default All UPC-E Settings> UPC-E0 On/Off Most U.P.C. barcodes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to read codes that lead with the 1 number sys- tem, use UPC-E1 (page 165).
Page 180 Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-E0 Addenda Required.
Page 181: Upc-E1
UPC-E0 Leading Zero This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan Off. Default = On. * On UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda.
Page 182: Ean/Jan-13
* UPC-E1 Off EAN/JAN-13 <Default All EAN/JAN Settings> EAN/JAN-13 On/Off * On Convert UPC-A to EAN-13 When UPC-A Converted to EAN-13 is selected, UPC-A barcodes are converted to 13 digit EAN-13 codes by adding a zero to the front. When Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A.
Page 183 EAN/JAN-13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda.
Page 184 EAN-13 Beginning with 290 Addenda Required This setting programs the scanner to require a 5 digit addenda only on EAN-13 barcodes that begin with “290.” The following settings can be programmed: Require 5 Digit Addenda: All EAN-13 barcodes that begin with “290” must have a 5 digit addendum.
Page 185 Require 2 Digit Addenda Require 5 Digit Addenda Require 2 or 5 Digit Addenda EAN-13 Beginning with 414/419 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 barcodes that begin with a “414” or “419.” The fol- lowing settings can be programmed: Require Addenda: All EAN-13 barcodes that begin with a “414”...
Page 186 EAN-13 Beginning with 434/439 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 barcodes that begin with a “434” or “439.” The fol- lowing settings can be programmed: Require Addenda: All EAN-13 barcodes that begin with a “434”...
Page 187 Default = Don’t Require 2 Digit Addenda. * Don’t Require 2 Digit Addenda Require 2 Digit Addenda EAN-13 Beginning with 978 Addenda Required These settings program the scanner to require a 5 digit addenda only on EAN-13 barcodes that begin with “978.” The following settings can be programmed: Require 5 Digit Addenda: All EAN-13 barcodes that begin with “978”...
Page 188 Default = Don’t Require 5 Digit Addenda. * Don’t Require 5 Digit Addenda Require 5 Digit Addenda Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for EAN/JAN-13 Addenda Required.
Page 189: Isbn Translate
ISBN Translate When On is scanned, EAN-13 Bookland symbols are translated into their equiva- lent ISBN number format. Default = Off. * Off EAN/JAN-8 <Default All EAN/JAN-8 Settings> EAN/JAN-8 On/Off * On EAN/JAN-8 Check Digit This selection allows you to specify whether or not the check digit should be trans- mitted at the end of the scanned data.
Page 190 EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 barcodes that...
Page 191: Msi
ting the timeout (from 0-120 milliseconds) by scanning digits from the Programming Chart, beginning on page 291 of this manual, then Save. Default = 500. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches. Addenda Timeout EAN/JAN-8 Addenda Separator When this feature is On, there is a space between the data from the barcode and the data from the addenda.
Page 192 MSI Check Character Different types of check characters are used with MSI barcodes. You can program the scanner to read MSI barcodes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI barcodes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data.
Page 193: Gs1 Databar Omnidirectional
MSI Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length GS1 DataBar Omnidirectional <...
Page 194: Gs1 Databar Limited
GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On GS1 DataBar Expanded Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information.
Page 195: Trioptic Code
Maximum Message Length Trioptic Code Note: If you are going to scan Code 32 Pharmaceutical codes (page 145), Trioptic Code must be off. Trioptic Code is used for labeling magnetic storage media. * Off Codablock A <Default All Codablock A Settings> Codablock A On/Off * Off If you are reading Code 39 barcodes, Codablock A should remain disabled.
Page 196: Codablock F
Codablock A Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-600. Minimum Default = 1, Maximum Default = 600. Minimum Message Length Maximum Message Length Codablock F <Default All Codablock F Settings>...
Page 197: Label Code
Maximum Message Length Label Code The standard Label Code is used in libraries. Default = Off. *Off PDF417 < Default All PDF417 Settings > PDF417 On/Off * On Granit XP User Guide...
Page 198: Macropdf417
PDF417 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750. Minimum Message Length Maximum Message Length MacroPDF417 MacroPDF417 is an implementation of PDF417 capable of encoding very large amounts of data into multiple PDF417 barcodes.
Page 199: Gs1 Composite Codes
* Off MicroPDF417 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366. Minimum Message Length Maximum Message Length GS1 Composite Codes Linear codes are combined with a unique 2D composite component to form a new...
Page 200: Gs1 Emulation
UPC/EAN Version Scan the UPC/EAN Version On barcode to decode GS1 Composite symbols that have a U.P.C. or an EAN linear component. (This does not affect GS1 Composite symbols with a GS1-128 or GS1 linear component.) Default = UPC/EAN Version Off. UPC/EAN Version On * UPC/EAN Version Off Note: If you scan coupons that have both UPC and GS1 Databar codes, you may wish to...
Page 201: Tcif Linked Code 39 (Tlc39)
If GS1 Code Expansion Off is scanned, retail code expansion is disabled, and UPC- E expansion is controlled by the UPC-E0 Expand (page 163) setting. If the AIM ID is enabled, the value will be the GS1-128 AIM ID, ]C1 (see Symbology Charts page 279).
Page 202: Qr Code
QR Code < Default All QR Code Settings > QR Code On/Off This selection applies to both QR Code and Micro QR Code. * On QR Code Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information.
Page 203 Swipe: Pull and hold down the trigger and scan all appended QR Codes while keep- ing the trigger pressed. The scanner emits short beeps for each partial QR Code that is scanned and buffered. One long beep is emitted after the last QR Code is scanned and the data is complete.
Page 204: Qr Code With Web Link
QR Code with Web Link Use this function to enable or disable the scanning of QR codes that contain “http” or “https”. Default = On. DotCode < Default All DotCode Settings > DotCode On/Off * Off Poor Quality DotCodes This setting improves the scanner’s ability to read damaged or badly printed Dot- Codes.
Page 205: Digimarc Barcode
DotCode Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-2400. Minimum Default = 1, Maximum Default = 2400. Minimum Message Length Maximum Message Length Digimarc Barcode™...
Page 206: Data Matrix
Default = Off. *Off Uses ID Decoder then Both Decoders Uses Digimarc Decoder then Both Decoders Uses ID Decoder then Alternates Decoders Uses Digimarc Decoder then Alternates Decoders Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off * On Granit XP User Guide...
Page 207 Direct Part Marking Decoding If you are having trouble reading Direct Part Marking (DPM) barcodes, scan Dot- peen DPM Decoding for Dotpeen codes or scan Reflective (Etched) DPM Decod- ing for reflective (etched) codes Default = Disable DPM Decoding. Dotpeen DPM Decoding * Disable DPM Decoding Reflective (Etched) DPM Decoding...
Page 208: Maxicode
Character Replacements on page 286), and scan the value and the Save barcode from the Programming Chart, beginning on page 291. The data characters should then appear properly. Data Matrix Code Page MaxiCode < Default All MaxiCode Settings > MaxiCode On/Off * Off MaxiCode Message Length Scan the barcodes below to change the message length.
Page 209: Aztec Code
Aztec Code < Default All Aztec Code Settings > Aztec Code On/Off * On Aztec Code Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-3832.
Page 210: Chinese Sensible (Han Xin) Code
Aztec Code Page Aztec Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar- code being scanned was created using a code page that is different from the one the host program is expecting.
Page 211: Postal Codes - 2D
Han Xin Code Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-7833. Minimum Default = 1, Maximum Default = 7833. Minimum Message Length Maximum Message Length Postal Codes - 2D The following lists the possible 2D postal codes, and 2D postal code combinations...
Page 212 Japanese Post On KIX Post On Planet Code On Also see Planet Code Check Digit, page 198. Postal-4i On Postnet On Postnet On Also see Postnet Check Digit, page 199. Postnet with B and B’ Fields On InfoMail On Combination 2D Postal Codes: InfoMail and British Post On Intelligent Mail Barcode and...
Page 213 Postnet and Postal-4i On Postnet and Intelligent Mail Barcode On Postal-4i and Intelligent Mail Barcode On Postal-4i and Postnet with B and B’ Fields On Planet Code and Postnet On Planet Code and Postnet with B and B’ Fields On Planet Code and Postal-4i On Planet Code and...
Page 214: Planet Code Check Digit
Planet Code, Postal-4i, and Intelligent Mail Barcode On Postnet, Postal-4i, and Intelligent Mail Barcode On Planet Code, Postal-4i, and Postnet with B and B’ Fields On Planet Code, Intelligent Mail Barcode, and Postnet with B and B’ Fields On Postal-4i, Intelligent Mail Barcode, and Postnet with B and B’...
Page 215: Postnet Check Digit
* Don’t Transmit Check Digit Postnet Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data. Default = Don’t Transmit. Transmit Check Digit * Don’t Transmit Check Digit Australian Post Interpretation This option controls what interpretation is applied to customer fields in Australian 4-State symbols.
Page 216: Postal Codes - Linear
Combination C and N Tables Postal Codes - Linear The following lists linear postal codes. Any combination of linear postal code selec- tions can be active at a time. China Post (Hong Kong 2 of 5) <Default All China Post (Hong Kong 2 of 5) Settings> China Post (Hong Kong 2 of 5) On/Off * Off China Post (Hong Kong 2 of 5) Message Length...
Page 217: Korea Post
Korea Post <Default All Korea Post Settings> Korea Post * Off Korea Post Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length Korea Post Check Digit...
Page 218 Granit XP User Guide...
Page 219: Chapter 8 - Imaging Commands
CHAPTER IMAGING COMMANDS The scanner is like a digital camera in the way it captures, manipulates, and trans- fers images. The following commands allow you to alter the way the scanner per- forms these functions. Single-Use Basis Imaging Commands with their modifiers send instructions to the scanner on a sin- gle-use basis, and take effect for a single image capture.
Page 220: Image Snap - Imgsnp
The modifiers for each of these commands follow the command description. Note: The images included with each command description are examples only. The results you achieve may be different from those included in this manual. The quality of the output you receive will vary depending on lighting, quality of the initial image/object being captured, and distance of the scanner from the image/object.
Page 221 T - Wait for Trigger Waits for a hardware trigger press before taking the image. This is only available when using Photo Style (1P). Takes image immediately (default) Waits for a trigger press, then takes the image L - LED State Determines if the LEDs should be on or off, and when.
Page 222 G - Gain Gain is used in Manual Style only (2P). Like a volume control, the gain modifier boosts the signal and multiplies the pixel value. As you increase the gain, the noise in an image is also amplified. No gain (default) Medium gain Heavy gain Maximum gain...
Page 223: Image Ship - Imgshp
U - Update Tries This sets the maximum number of frames the scanner should take to reach the Delta for Acceptance. Update Tries is only available when using Photo Style (1P). (Default = 6) Range: 0 - 10 % - Target Set Point Percentage Sets the target point for the light and dark values in the captured image.
Page 224: Imgshp Modifiers
IMGSHP Modifiers A - Infinity Filter Enhances pictures taken from very long distances (greater than 10 feet or 3m). The Infinity Filter should not be used with IMGSNP Modifiers (page 204). Infinity filter off (default) Infinity filter on Example: Infinity Filter off (0A) Infinity Filter on (1A) from approximately 12 feet from approximately 12 feet (3.66m)
Page 225 E - Edge Sharpen An edge sharpen filter cleans up the edges of an image, making it look cleaner and sharper. While edge sharpening does make the image look cleaner, it also removes some fine detail from the original image. The strength of the edge sharpen filter can be entered from 1 to 24.
Page 226 H - Histogram Stretch Increases the contrast of the transmitted image. Not available with some image formats. No stretch (default) Histogram stretch Example: Histogram Stretch at 0H: Histogram Stretch at 1H: I - Invert Image Invert image is used to rotate the image around the X or Y axis. Invert around the X axis (flips picture upside down) Invert around the Y axis (flips picture left to right) Example:...
Page 227 IF- Noise Reduction Used to reduce the salt and pepper noise in an image. No salt and pepper noise reduction (default) Salt and pepper noise reduction Example: Noise Reduction Off (0if): Noise Reduction On (1if): IR - Image Rotate Image as snapped (rightside up) (default) Rotate image 90 degrees to the right Rotate image 180 degrees (upside down) Rotate image 90 degrees to the left...
Page 228 J - JPEG Image Quality Sets the desired quality when the JPEG image format is selected. Higher numbers result in higher quality, but larger files. Smaller numbers result in greater amounts of lossy compression, faster transmission times, lower quality, but smaller files. (Default = 50) Image is compressed as much as possible while preserving quality factor of n (n = 0 - 100)
Page 229 The bottom edge of the shipped image corresponds to row n - 1 of the image in memory. Range: 000 - 639. (Default = all rows) Example: Uncropped Image: Image Crop set to Image Crop set to 300R: 300L: Image Crop set to 200B: Image Crop set to 200T: Alternately, specify the number of pixels to cut from the outside margin of the image;...
Page 230 The smaller number of pixels shipped, the smaller the image, however, after a cer- tain point the image becomes unusable. ship every pixel (default) ship every 2nd pixel, both horizontally and vertically ship every 3rd pixel, both horizontally and vertically Pixel Ship Pixel Ship Example:...
Page 231: Image Size Compatibility
V - Blur Image Smooths transitions by averaging the pixels next to the hard edges of defined lines and shaded areas in an image. Don’t blur (default) Blur Example: Blur Image Off (0V): Blur Image On (1V): W - Histogram Ship A histogram gives a quick picture of the tonal range of an image, or key type.
Page 232: Intelligent Signature Capture - Imgbox
* Native Resolution Intelligent Signature Capture - IMGBOX IMGBOX allows you to configure the size and location of a signature capture area relative to its proximity to a barcode. This allows you to tailor a signature capture area to a specific form. In order to use IMGBOX, you need a set form where the sig- nature box location is in a known location relative to a barcode.
Page 233: Imgbox Modifiers
To see this example, align the aimer with the signature area (not with the barcode), then press the trigger. Send the following IMGBOX command string after the trigger press: Example: IMGBOX245w37h55y. Note: Case is not important in the command string. It is used here only for clarity. The following image is captured: The IMGBOX commands have many different modifiers that can be used to change the size and appearance of the signature image output by the scanner.
Page 234 B - Output Image Height This option is used to size the image vertically. If using this option, set the resolu- tion (R) to zero. Example: Image Height set to 50B: Image Height set to 100B: D - Pixel Depth This indicates the number of bits per pixel in the transmitted image, which defines whether it will be grayscale or black and white.
Page 235 H - Height of Signature Capture Area The height of the signature capture area must be measured in inches divided by .01. In the example, the height of the area to be captured is 3/8 inch, resulting in a value of H = .375/0.01 = 37.5. Example: IMGBOX245w37h55y.
Page 236 decimal point between the first and second digit. For example, use 2500 to specify a resolution of 2.5. Set to zero when using the A and B modifiers (see A - Output Image Width B - Output Image Height on page 218). Example: Resolution set to 0R: Resolution set to 1000R:...
Page 237: Rf Default Imaging Device
Y - Vertical Barcode Offset The vertical barcode offset allows you to offset the vertical center of the signature capture area. Negative numbers indicate that the signature capture is above the barcode, and positive numbers indicate that the area is below the barcode. Mea- surements are in multiples of the minimum bar width Example: Vertical Offset set to -7Y:...
Page 238 Granit XP User Guide...
Page 239: Chapter 9 - Utilities
CHAPTER UTILITIES To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page 279 for the single char- acter code that identifies each symbology.) This action first clears all current pre- fixes, then programs a Code I.D.
Page 240: Totalfreedom
Decoding apps and Data Formatting apps can be created using TotalFreedom. For further information about TotalFree- dom, go to our website at sps.honeywell.com. Application Plug-Ins (Apps) Any apps that you are using can be turned off or on by scanning the following bar- codes.
Page 241: Ezconfig For Scanning Introduction
Configure with EZConfig for Scanning Use the EZConfig for Scanning tool to configure your scanner online: 1. Access the Honeywell Technical Support Downloads Portal at honeywell.com/ PSSsoftware-downloads. 2. Go to Software > Barcode Scanners > Software > Tools and Utilities >...
Page 242: Reset The Factory Defaults
Reset the Factory Defaults Caution: This selection erases all your settings and resets the scanner to the original factory defaults. It also disables all plugins. If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scanner to factory default settings, first scan the Remove Custom Defaults barcode, then scan Activate Defaults.
Page 243: Chapter 10 - Serial Programming Commands
CHAPTER SERIAL PROGRAMMING COMMANDS The serial programming commands can be used in place of the programming bar- codes. Both the serial commands and the programming barcodes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming barcode in this manual. The device must be set to an RS232 interface (see page 14).
Page 244: Query Commands
scanner. This setting is changed by using the BT_NAM command, which accepts alphanumeric values. If the name is not known, a wild- card (*) can be used :* Note: Since the base stores all work group settings and transfers to them to scanner once they are linked, changes are typically done to the base and not to the scanner.
Page 245 SubTag Field Usage When a query is used in place of a SubTag field, the query applies only to the sub- set of commands available that match the Tag field. In this case, the Data field should not be used because it is ignored by the device. Data Field Usage When a query is used in place of the Data field, the query applies only to the spe- cific command identified by the Tag and SubTag fields.
Page 246: Trigger Commands
This response indicates that Codabar Coding Enable (CBRENA) has a range of val- ues from 0 to 1 (off and on). Example: What is the default value for Codabar Coding Enable? Enter: cbrena^. Response: CBRENA1[ACK] This response indicates that the default setting for Codabar Coding Enable (CBRENA) is 1, or on.
Page 247: Reset The Custom Defaults
The scanner scans until a barcode has been read, until the deactivate command is sent, or until the serial time-out has been reached (see Read Time-Out on page 85 for a description, and the serial command on page 241). Reset the Custom Defaults If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults barcode below.
Page 248: Menu Commands
*Report PID as built USBXnn0 Report PID as Granit 1910i USBXnn3 Report PID as Granit 1980i USBXnn4 Plug and Play Codes Verifone Ruby Terminal PAPRBY Gilbarco Terminal PAPGLB Honeywell Bioptic Aux Port PAPBIO Datalogic Magellan Aux Port PAPMAG Granit XP User Guide...
Page 249 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Wincor Nixdorf Terminal PAPWNX Wincor Nixdorf Beetle PAPBTL Wincor Nixdorf RS232 Mode A PAPWMA Program Keyboard *U.S.A. KBDCTY0 Country Albania KBDCTY35 Azeri (Cyrillic) KBDCTY81 Azeri (Latin) KBDCTY80 Belarus KBDCTY82 Belgium...
Page 250 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Greek (Polytonic) KBDCTY60 Hebrew KBDCTY12 Hungarian (101 key) KBDCTY50 Hungary KBDCTY19 Iceland KBDCTY75 Irish KBDCTY73 Italian (142) KBDCTY56 Italy KBDCTY5 Japan ASCII KBDCTY28 Kazakh KBDCTY78 Kyrgyz (Cyrillic) KBDCTY79 Latin America KBDCTY14...
Page 251 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Sweden KBDCTY23 Switzerland (French) KBDCTY29 Switzerland (German) KBDCTY6 Tatar KBDCTY85 Turkey F KBDCTY27 Turkey Q KBDCTY24 Ukrainian KBDCTY76 United Kingdom KBDCTY7 United Stated (Dvorak right) KBDCTY89 United States (Dvorak left) KBDCTY88 United States (Dvorak) KBDCTY87...
Page 252 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Keyboard Modifiers *Control + X Off KBDCAS0 DOS Mode Control + X KBDCAS1 Windows Mode Control + X KBDCAS2 Windows Mode Prefix/Suffix Off KBDCAS3 DOS Mode Control + X Mode On KBDCAS4 with Windows Mode Prefix/Suffix Supports ALT 3 Digit HEX Mode...
Page 253 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry RS232 Handshaking *RTS/CTS Off 232CTS0 Flow Control, No Timeout 232CTS1 Two-Direction Flow Control 232CTS2 Flow Control with Timeout 232CTS3 RS232 Timeout (1-5100 232DEL#### milliseconds) *XON/XOFF Off 232XON0 XON/XOFF On 232XON1 *ACK/NAK Off...
Page 254 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Beeper Pitch - Base Error *Low/Razz (250 Hz) (min 200 Hz) BASFQ2250 Medium (3250 Hz) BASFQ23250 High (4200 Hz) (max 9000 Hz) BASFQ24200 Number of Beeps - Base Error *1 (Range 1 - 9) BASERR# Scanner Report...
Page 255 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Batch Mode Quantity *Off BATQTY0 BATQTY1 Quantity Codes BATNUM0 BATNUM1 BATNUM2 BATNUM3 BATNUM4 BATNUM5 BATNUM6 BATNUM7 BATNUM8 BATNUM9 Batch Mode Output Order *FIFO BATLIF0 LIFO BATLIF1 Total Records Total Records BATNRC Delete Last Code...
Page 256 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Bluetooth HID Japanese PAPJKB Keyboard Connect Bluetooth HID Keyboard PAPSPP Disconnect Virtual Keyboard Disable BT_DBL0 *Enable BT_DBL1 Bluetooth Serial Port - PCs/ Non-Base BT Connection BT_TRM0;BT_DNG5 Laptops PDA’s/Mobility Systems Devices BT Connection - PDA/Mobility BT_TRM0;BT_DNG1...
Page 257 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry High (4200 Hz) (max 9000 Hz) BEPFQ14200 Vibrate - Good Read Vibrate - Good Read Off TFBGRD0 *Vibrate - Good Read On TFBGRD1 Vibrate Duration Duration TFBDUR#### (100 - 2,000 ms) *100 Beeper Pitch - Error (Frequency) *Razz (250 Hz) (min 200 Hz)
Page 258 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Presentation LED Behavior After *LEDs On TRGPCK1 Decode LEDs Off TRGPCK0 Presentation Centering Window Presentation Centering On PDCWIN1 *Presentation Centering Off PDCWIN0 Left of Presentation Centering PDCLFT### Window (*40%) Right of Presentation Centering PDCRGT###...
Page 259 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Reread Delay Short (500 ms) DLYRRD500 *Medium (750 ms) DLYRRD750 Long (1000 ms) DLYRRD1000 Extra Long (2000 ms) DLYRRD2000 User-Specified Range 0 - 30,000 ms DLYRRD##### 2D Reread Delay *2D Reread Delay Off DLY2RR0 Short (1000ms)
Page 260 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Centering Window Centering On DECWIN1 *Centering Off DECWIN0 Left of Centering Window (*40%) DECLFT### Right of Centering Window DECRGT### (*60%) Top of Centering Window (*40%) DECTOP### Bottom of Centering Window DECBOT### (*60%) Preferred Symbology...
Page 261 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry *Good Read Click - Each Code in BEPSIN1 Sequence Good Read Beep - Partial BEPISE0 Sequence Output *Error Tone - Partial Sequence BEPISE1 Output Multiple Symbols SHOTGN1 *Off SHOTGN0 No Read...
Page 262 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Data Formatter Selections Data Format Editor *Default Data Format (None) DFMDF3 Show Data Format Settings DFMBK3? Enter Data Format DFMBK3## Clear One Data Format DFMCL3 Clear All Data Formats DFMCA3 Data Formatter Data Formatter Off...
Page 263 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Codabar Concatenation *Off CBRCCT0 CBRCCT1 Require CBRCCT2 Codabar Message Length Minimum (2 - 60) *4 CBRMIN## Maximum (2 - 60) *60 CBRMAX## Code 39 Default All Code 39 Settings C39DFT C39ENA0 C39ENA1...
Page 264 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry NEC 2 of 5 Check Digit *No Check Digit N25CK20 Validate, But Don’t Transmit N25CK21 Validate and Transmit N25CK22 NEC 2 of 5 Message Length Minimum (2 - 80) *4 N25MIN## Maximum (2 - 80) *80 N25MAX##...
Page 265 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Code 11 Message Length Minimum (1 - 80) *4 C11MIN## Maximum (1 - 80) *80 C11MAX## Code 128 Default All Code 128 Settings 128DFT 128ENA0 128ENA1 ISBT Concatenation *Off ISBENA0 ISBENA1...
Page 266 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry UPC-A Addenda Required *Not Required UPAARQ0 Required UPAARQ1 Addenda Timeout Range (0 - 500) *120 DLYADD##### UPC-A Addenda UPAADS0 Separator UPAADS1 UPC-A/EAN-13 with Extended *Off CPNENA0 Coupon Code Allow Concatenation CPNENA1 Require Concatenation...
Page 267 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry EAN/JAN-13 Check Digit E13CKX0 E13CKX1 EAN/JAN-13 Addenda 2 Digit Addenda On E13AD21 *2 Digit Addenda Off E13AD20 5 Digit Addenda On E13AD51 *5 Digit Addenda Off E13AD50 EAN/JAN-13 Addenda Required *Not Required E13ARQ0...
Page 268 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry EAN/JAN-8 Check Digit EA8CKX0 EA8CKX1 EAN/JAN-8 Addenda *2 Digit Addenda Off EA8AD20 2 Digit Addenda On EA8AD21 *5 Digit Addenda Off EA8AD50 5 Digit Addenda On EA8AD51 EAN/JAN-8 Addenda Required *Not Required EA8ARQ0...
Page 269 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry GS1 DataBar Expanded Default All GS1 DataBar RSEDFT Expanded Settings RSEENA0 RSEENA1 GS1 DataBar Expanded Msg. Minimum (4 - 74) *4 RSEMIN## Length Maximum (4 - 74) *74 RSEMAX## Trioptic Code *Off...
Page 270 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry GS1 Composite Codes Msg. Minimum (1-2435) *1 COMMIN#### Length Maximum (1-2435) *2435 COMMAX#### GS1 Emulation GS1-128 Emulation EANEMU1 GS1 DataBar Emulation EANEMU2 GS1 Code Expansion Off EANEMU3 EAN8 to EAN13 Conversion EANEMU4 *GS1 Emulation Off...
Page 271 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Data Matrix Default All Data Matrix Settings IDMDFT IDMENA1 IDMENA0 Direct Part Marking (DPM) Dotpeen DPM Decoding DPMENA1 Decoding *Disable DPM Decoding DPMENA0 Reflective (Etched) DPM DPMENA2 Decoding Data Matrix Msg.
Page 272 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Single 2D Postal Codes Australian Post On POSTAL1 British Post On POSTAL7 Canadian Post On POSTAL30 Intelligent Mail Barcode On POSTAL10 Japanese Post On POSTAL3 KIX Post On POSTAL4 Planet Code On POSTAL5...
Page 273 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Planet, Postal-4i, Intelligent Mail POSTAL28 Barcode, and Postnet On Planet, Postal-4i, Intelligent Mail POSTAL29 Barcode, and Postnet with B and B’ Fields On Planet Code Check Digit Transmit PLNCKX1 *Don’t Transmit...
Page 274 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Exposure (1-7874 microseconds) SNPEXP *7874 *Gain - None SNPGAN1 Gain - Medium SNPGAN2 Gain - Heavy SNPGAN4 Gain - Maximum SNPGAN8 Target White Value (0-255) *125 SNPWHT### Delta for Acceptance (0-255) *25 SNPDEL### Update Tries (0-10) *6...
Page 275 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Rotate Image 90° right IMGROT1 Rotate Image 180° right IMGROT2 Rotate Image 90° left IMGROT3 JPEG Image Quality (0-100) *50 IMGJQF### *Gamma Correction Off IMGGAM0 Gamma Correction On (0-1000) IMGGAM### Image Crop - Left (0-843) *0 IMGWNL###...
Page 276 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Application Plug-Ins (Apps) *Decoding Apps On PLGDCE1 Decoding Apps Off PLGDCE0 *Formatting Apps On PLGFOE1 Formatting Apps Off PLGFOE0 List Apps PLGINF Reset the Factory Defaults Remove Custom Defaults DEFOVR Activate Defaults DEFALT...
Page 277: Chapter 11 - Product Specifications
CHAPTER PRODUCT SPECIFICATIONS Granit XP 1990i SR, XR, XLR Corded Scanner Product Specifications Parameter Specification Mechanical Height 7.5 inches (192mm) Length 3.9 inches (100mm) Width 2.9 inches (76mm) Weight 11.2 ounces (320g) Electrical Voltage Requirements 4.4 to 5.5 VDC at input connector Current Draw ScanningStandby 500mA @ 5VDC, 2.5W...
Page 278: Granit Xp 1991I Sr, Xr, Xlr Cordless Scanner Product Specifications
Parameter (Continued) Specification ESD Tolerance Up to ±20kV direct air Up to 8 kV indirect coupling plane Image Image Size 1280 x 800 pixels Scan Performance Skew Angle +65° Pitch Angle 1D barcode 1D code: +65° 2D barcode 2D code: +45° Motion Tolerance Up to 4.5 m/s (157 in/s) for 13 mil UPC at optimal focus...
Page 279 Parameter (Continued) Specification Expected Charge Time 4.5 hours + 0.5 hours Radio Frequency 2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v 4.2 Range 33 ft. (10 m) typical Environmental Temperature Ranges: Operating -4°F to +122°F (-20°C to 50°C) Charging 32°F to 113°F (0°C to 45°C) Storage with battery*...
Page 280: Ccb22-100Bt-03N/Cob22 Charge Base Product Specifications
CCB22-100BT-03N/COB22 Charge Base Product Specifications Parameter Specification Mechanical Height 2.3 inches (60 mm) Length 9.6 inches (245 mm) Width 4.0 inches (102 mm) Weight CCB22 10.4 oz (295g) COB22 10.2 oz (290g) Electrical Voltage: 4.0 to 5.5 VDC Current Draw: Host Terminal Port 500mA Aux Power Port...
Page 281: Depth Of Field Charts
Depth of Field Charts Granit XP SR Performance Focus Typical Spec Guaranteed Spec 3 mil Code 39 1.53 4.09 2.55 1.92 3.58 1.65 5 mil Code 39 0.78 8.66 7.87 1.02 7.75 6.73 10mil Code 39 19.29 19.29 0.39 17.75 17.36 13 mil UPC 19.84...
Page 282: Granit Xp Xr Performance
Granit XP XR Performance Focus Typical Spec Guaranteed Spec 3 mil Code 39 1.53 4.09 2.55 1.92 3.58 1.65 5 mil Code 39 0.78 8.66 7.87 1.02 7.75 6.73 10mil Code 39 1215 1215 1022 1425 47.83 47.83 0.39 40.23 56.10 10.4 mil C128 13.5...
Page 283: Granit Xp Xlr Performance
Granit XP XLR Performance Focus Average Spec Guaranteed Spec 5 mil Code 39 3.43 14.57 11.14 4.25 13.31 9.06 10 mil DM 15.47 11.97 4.80 14.05 9.25 10 mil Code 39 2202 2154 1461 1397 1.89 86.70 84.8 2.51 57.52 55.01 13 mil UPCA 2244...
Page 284: Standard Connector Pinouts
Standard Connector Pinouts Note: The following pin assignments are not compatible with some Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty.
Page 285: Rs485 Output
RS485 Output 10 Pin RJ41 Modular Plug - connects to the base Note: RS485 signal conversion is performed in the cable. Cable shield Cable select Supply ground Transmit data Receive data - serial data to scanner +5V power Transmit Enable 10 Pin Modular Plug - connects to the base Cable shield Cable select...
Page 286: Required Safety Labels
Required Safety Labels Scanner Laser Label location Part Number, Serial Number and Compliance label location Revision Information location Granit XP User Guide...
Page 287: Ccb22-100Bt-03N-Bf Base
CCB22-100BT-03N-BF Base Granit XP User Guide...
Page 288 Granit XP User Guide...
Page 289: Chapter 12 - Maintenance And Troubleshooting
CHAPTER MAINTENANCE AND TROUBLESHOOTING Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center (see Customer Support page xiii). Maintenance Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the following sections describe periodic checks to ensure dependable operation.
Page 290: Inspect Cords And Connectors
When properly seated, the connector is held in place with a screw and locking plate. The interface cable is designed to be field replaceable. • Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable.
Page 291: Change A Scanner Battery
Change a Scanner Battery 1. Rotate metal twist at bottom of battery door counterclockwise. 2. Remove battery. 3. Insert replacement battery. 4. Replace end cap and screw together. Troubleshoot a Corded Scanner The scanner automatically performs self-tests whenever you turn it on. If your scanner is not functioning properly, review the following Troubleshooting Guide to try to isolate the problem.
Page 292: Troubleshoot A Cordless System
Troubleshoot a Cordless System Troubleshoot a Base Note: Visit the Services and Support section of our website (sps.honeywell.com) to check for the latest software for both the scanner and the base. If your base is not functioning properly, review the following troubleshooting guidelines to try to isolate the problem.
Page 293 into your application. Refer to Prefix/Suffix Overview on page 113 for further information. The scanner won’t read your barcode at all. • Scan the sample barcodes in the back of this manual. If the scanner reads the sample barcodes, check that your barcode is readable. •...
Page 294 Granit XP User Guide...
Page 295: Chapter A - Reference Charts
Refer to Data Edit beginning on page 113 and Data Format beginning on page 119 for information about using Code ID and AIM ID. Linear Symbologies Honeywell Possible modifiers Linear Symbology All Symbologies Codabar Code 11 Code 128 0, 1, 2, 4 Code 32 Pharmaceutical (PARAF) <...
Page 296 0, 1, 2, 3, 8, 9, A, B, C UPC-A UPC-A with Add-On UPC-A with Extended Coupon Code UPC-E UPC-E with Add-On UPC-E1 Add Honeywell Code ID 5C80 Add AIM Code ID 5C81 Add Backslash 5C5C Batch mode quantity Granit XP User Guide...
Page 297: 2D Symbologies
2D Symbologies Honeywell Possible modifiers 2D Symbology All Symbologies Aztec Code 0-9, A-C Chinese Sensible Code (Han Xin Code) Codablock A 0, 1, 4, 5, 6 Codablock F 0, 1, 4, 5, 6 Data Matrix Dot Code GS1 Composite GS1 DataBar Omnidirectional...
Page 298: Ascii Conversion Chart (Code
ASCII Conversion Chart (Code Page 1252) In keyboard applications, ASCII Control Characters can be represented in 3 differ- ent ways, as shown below. The CTRL+X function is OS and application dependent. The following table lists some commonly used Microsoft functionality. This table applies to U.S.
Page 299: Lower Ascii Reference Table
Lower ASCII Reference Table Note: Windows Code page 1252 and lower ASCII use the same characters. Printable Characters Character Character DEC Character <SPACE> " & < > ⌂ Extended ASCII Characters CP 1252 ASCII Alternate Extended PS2 Scan Code ↑ €...
Page 300 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code Œ î Reserved ì Reserved Ž Ä Numeric Keypad Enter 0x1C Å Numeric Keypad / 0x35 É 0x3B ‘ æ 0x3C ’ Æ 0x3D “ ô 0x3E ” ö...
Page 301 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code Â ┬ Ã ├ Ä ─ Å í Æ ╞ Ç ╟ È ╚ É ╔ Ê ╩ Ë ╦ Ì ╠ Í ═ Î ╬ Ï ╧ Ð...
Page 302: Iso 2022/Iso 646 Character Replacements
(standard ASCII) Automatic National Character ISO/IEC 2022 2 (default) Replacement Binary Code page Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code 39 and Code 93. United States ISO/IEC 646-06 Canada ISO /IEC 646-121...
Page 303 à â ç ê î ô é ù è û à â ç ê É ô é ù è û ‾ ¥ ‾ ¥ £ ˜ £ à ° ç § µ é ù è ¨ § Ä Ö Ü ä...
Page 304: Keyboard Key References
Keyboard Key References 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 4B 50 55 5A 5F 64 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 4C 51 56 5B 60 65 1F 20 21 22 23 24 25 26 27 28 29...
Page 305: Sample Symbols
SAMPLE SYMBOLS UPC-A Interleaved 2 of 5 01234567890 0 123456 7890 EAN-13 9 780330 290951 Code 128 Code 39 Code 128 BC321 Codabar A13579B Code 93 Straight 2 of 5 Industrial 123456 123456-9$ Matrix 2 of 5 6543210 RSS-14 PDF417 Car Registration (01) 00123456789012 Code 49...
Page 306 SAMPLE SYMBOLS (CONTINUED) Postnet Data Matrix Zip Code Test Symbol QR Code Numbers MaxiCode Micro PDF417 Test Message Test Message DotCode 12345 Granit XP User Guide...
Page 307: Programming Chart
PROGRAMMING CHART Granit XP User Guide...
Page 308 PROGRAMMING CHART (CONTINUED) Save Discard Reset Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again. Granit XP User Guide...
Page 310 Honeywell 855 S. Mint St. Charlotte, NC 28202 sps.honeywell.com ™ 199x-EN-UG-01 Rev E 08/22...

This manual is also suitable for:

Granit 1990isr Granit 1990ixr Granit 1990ixlr Granit 1991isr Granit 1991ixr Granit 1991ixlr

Honeywell Granit XP 199xi Series User Manual

Chapter 1 - Get Started

Chapter 2 - Program the Interface

Chapter 3 - Cordless System Operation

Chapter 4 - Input/Output Settings

Chapter 5 - Data Edit

Chapter 6 - Data Format

Chapter 7 - Symbologies

Chapter 8 - Imaging Commands

Quick Links

Related Manuals for Honeywell Granit XP 199xi Series

Summary of Contents for Honeywell Granit XP 199xi Series