Table of Contents
Advertisement
7.15 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡ After the appliance has been switched off, LED 1
flashes in the LED display for the grease filter satura-
tion display and/or LED 2 flashes for the saturation
indicator for the odour filter.
¡ A signal sounds repeatedly.
Press
.
▶
a The saturation indicator is reset.
7.16 Switching on the lighting
The lighting can be switched on and off independently
of the ventilation system.
Press .
▶
7.17 Setting the brightness
Press and hold
or .
▶
Note: Colour temperature settings are available in the
Home Connect app provided the appliance has this
function.
7.18 Switching on the button tone
The button tones can be switched on.
Requirement: The appliance is switched off.
Home Connect
8 Home Connect
This appliance is network-capable. Connecting your ap-
pliance to a mobile device lets you control its functions
via the Home Connect app, adjust its basic settings
and monitor its operating status.
The Home Connect services are not available in every
country. The availability of the Home Connect function
depends on the availability of Home Connect services
in your country. You can find information about this at:
www.home-connect.com.
The Home Connect app guides you through the entire
login process. Follow the instructions in the Home Con-
nect app to configure the settings.
If the appliance is not connected to your home net-
work, it functions as an appliance with no network con-
nection and can still be operated via the display.
Tip: Please also follow the instructions in the
Home Connect app.
Notes
¡ Please note the safety precautions in this instruction
manual and make sure that they are also observed
when operating the appliance via the Home Con-
nect app.
→ "Safety", Page 2
¡ Operating the appliance on the appliance itself al-
ways takes priority. During this time it is not possible
to operate the appliance using the Home Connect
app.
Press and hold
and
1.
a In the LED display, the LED for the setting that is
currently selected lights up.
Press
or until LED 1 lights up in the LED dis-
2.
play.
To cancel the setting, press .
To save the setting, press and hold
3.
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
7.19 Switching the button tone off
The button tones can be switched off.
Note: Signal tones for the appliance are always
switched on and cannot be switched off.
Requirement: The appliance is switched off.
Press and hold
and
1.
a In the LED display, the LED for the setting that is
currently selected lights up.
Press
or until LED 2 lights up in the LED dis-
2.
play.
To cancel the setting, press .
To save the setting, press and hold
3.
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
¡ In networked standby mode, the appliance requires
a maximum of 2 W.
¡ If you need your device's MAC address to connect
to your home network, you can find this next to the
rating plate. → Page 15
8.1 Setting up the Home Connect app
Install the Home Connect app on your mobile
1.
device.
Start the Home Connect app and set up access for
2.
Home Connect.
The Home Connect app guides you through the en-
tire login process.
8.2 Setting up Home Connect
Requirements
¡ The appliance is switched off.
¡ You have a mobile device with a current version of
the iOS or Android operating system, e.g. a smart-
phone.
¡ The Home Connect app has been installed on your
mobile device.
¡ The appliance is receiving signals from the WLAN
home network (Wi-Fi) at its installation location.
¡ The mobile device and the appliance are within
range of your home network's Wi-Fi signal.
Open the Home Connect app and scan the follow-
1.
ing QR code.
Home Connect en
for approx. three seconds.
and
for ap-
for approx. three seconds.
and
for ap-
9
Advertisement
Table of Contents
