Table of Contents
Advertisement
en Basic operation
so oft drücken, bis in der LED-Anzeige die LED 4
1.
für die Intensivstufe 1 leuchtet.
so oft drücken, bis in der LED-Anzeige die LED 5
2.
für die Intensivstufe 2 leuchtet.
a After approx. 6 minutes, the appliance automatically
switches to fan setting 3.
7.5 Switching off intensive mode
To select a fan setting of your choice, press
▶
7.6 Switching on the fan run-on
Press
.
▶
a LED 1 for the fan setting lights up in the LED dis-
play. LED 6 flashes for the fan run-on.
a The appliance switches off automatically after ap-
prox. 10 minutes.
7.7 Switching off the fan run-on
Press
.
▶
a This immediately stops the fan run-on.
a The appliance switches to the fan setting that was
previously selected.
7.8 Intermittent ventilation
In order to regularly ventilate your kitchen, you can use
the interval ventilation. With interval ventilation, the vent-
ilation system switches on and off in the selected set-
ting for the selected time.
Note: This function is only available in the Home Con-
nect app.
If the interval ventilation is switched on, LED 6 continu-
ously flashes in the LED display for the interval ventila-
tion and the LED for the selected fan setting lights up.
As soon as the ventilation time ends, the LED for the
fan setting you have selected goes out. LED 6 contin-
ues to flash.
7.9 Switching on automatic mode
The optimum fan setting is set automatically using a
sensor.
Press
.
▶
a In the LED display, LED 6 lights up for automatic
mode.
7.10 Switch off automatic mode
Press
.
▶
a The appliance switches to the fan setting that was
previously set.
a The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a Automatic mode runs for a maximum of four hours.
1
Depending on the appliance specifications
8
7.11 Sensor sensitivity
In automatic mode, a sensor in the appliance detects
the intensity of the cooking odours and roasting
odours. Depending on the setting of the sensor sensit-
ivity, the optimum fan setting is automatically switched
on.
If the sensor control reacts too weakly or too strongly,
you can change the setting for the sensor sensitivity.
¡ Default setting: Fan setting 3
.
¡ Lowest setting: Fan setting 1
¡ Highest setting: Fan setting 5
7.12 Setting the sensor sensitivity
Requirement: The appliance is switched off.
1.
2.
3.
a A signal tone sounds as soon as the selected set-
7.13 Saturation indicator
If the grease filters or odour filters are saturated, cor-
responding symbols flash after the appliance is
switched off.
Note: You can set the saturation indicator in the Home
Connect app depending on the filter used.
Clean the saturated grease filters and, in doing so, ob-
serve the cleaning instructions in these instructions.
Change the saturated odour filters and observe the in-
structions in the accompanying instructions.
If odour filters can be regenerated, follow the instruc-
tions in the accompanying instructions.
7.14 Setting the saturation indicator
1
The saturation indicator must be adjusted depending
on the filter used.
Requirement: The appliance is switched off.
1.
1
2.
a A signal tone sounds as soon as the selected set-
Press and hold
and
Press
or
to change the setting.
To cancel the setting, press .
To save the setting, press and hold
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
ting is saved.
Press and hold
and
To set circulating-air mode (non-regenerable fil-
‒
ter), press
/
until LED 2 lights up in the LED
display.
To set circulating-air mode (non-regenerable fil-
‒
ter), press
/
until LED 3 lights up in the LED
display.
To convert the electronic control back to opera-
‒
tion without the air recirculation filter, press
until LED 1 lights up on the LED display.
To save the setting, press and hold and for ap-
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
To cancel the setting, press .
ting is saved.
1
1
for approx. 3 seconds.
and
for ap-
for approx. three seconds.
/
Advertisement
Table of Contents
