Page 3
Let's get started. You're excited to power up, so we'll keep this brief!
Page 4
Thank you for purchasing your Energizer Angle grinder ® EZ900AG EZ900AG-100 EZ900AG-125 EZ1100AG EZ1100AG-125 This manual will show you the great features of Energizer Angle grinder EZ900AG/EZ900AG-100/EZ900AG-125/EZ1100AG/EZ1100AG-125 ®...
Page 5
INDEX Contain Page 1. Advertencias generales de seguridad 2. Lista de piezas 3. Advertencias de seguridad generales de la herramienta eléctrica 4. Mantenimiento 5. Solución de problemas 6. Instrucciones de seguridad para todas las operaciones 7. Otras instrucciones de seguridad para todas las operaciones 8.
1. GENERAL SAFETY WARNINGS WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, re and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your electric (corded) power tool or battery-operated (cordless) power tool.
location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 3)PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the in uence of drugs, alcohol or medication.
• Lubricate all moving parts at regular intervals. CAUTION :Water must never come into contact with the tool. If the supply cord of this power tool is damaged, it must be replaced by a specially prepa- red cord available through the service organisation. 5.
e) The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled d) The arbour size of wheels, anges, backing pads or any other accessory must properly t the spindle of the power tool.Accessories with arbour holes that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.
Page 10
or any other accessory. Pinching or snagging causes rapid stalling of the rotating acces- sory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory's rotation at the point of the binding. For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out.
out of the cut. 7. OVERLOAD Overloading will cause damage to the motor of your angle grinder. This can happen if your angle grinder is subjected to heavy use for prolonged periods of time. Do not in any circumstances, attempt to exert too much pressure on your angle grinder to speed up your work.
To lock the on/off switch (D), press the on/off switch (D) down at the front until it engages. To switch off the power tool, release the on/off switch (D) or, if it is locked, brie y press down the back of the on/off switch (D) and then release it 5.TO USE THE GRINDER Attention: Do not switch the grinder on whilst the disc is in contact with the workpiece.
c) When wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the whee丨 is in motion otherwise kickback may occur.
• Do not allow the end of the spindle to contact the base of the hole in the abrasive consu- mable. Do not work in areas where there may be concealed electricity cables or gas or water pipes. Use a suitable detector or ask your local utility service providers. Contact with electricity cables can lead to re or electric shock Damaging a gas pipe can lead to an explosion.
Refer to the accessory packaging for further details. Store personnel can assist you and offer advice. 14. TECHNICAL SPECIFICATIONS EZ1100AG EZ900AG-100 Power: 1100 W Power: 900 W Voltage: 220-240 V ~ 50 Hz...
WARRANTY Product model Date of sale Company Serial number Client's signature Username The product is in good conditions and fully complete. Read and agree the terms of the warranty. The manufacturer warrants the product against faulty materials and workmanship for a period of 1 year from the date of first purchaser to the original purchaser.