Safety Instructions; Before Use - Husqvarna 600 H Operating Instructions Manual

4. Safety Instructions
1. Always disconnect the plug from the
yx mains socket before carrying out any
cljwork on the equipment, before cleaning
and before moving the equipment.
2. The use of hedge trimmers involves certain
risks. Attention: Danger! Rotating machi-
cljnery.
3. The hedge trimmer should always be held
with both hands.
4. ' Before using the equipment clear the working
area of any foreign objects (e.g. stones)
and be aware of foreign objects during
operation of the machine! If the machine
becomes jammed e.g. by thick branches,
switch off and disconnect the machine
from the mains socket before investigating
and rectifying the cause of the jam. Take
special care when switching the machine
on again.
5. Check the flex and all connections for any
visible faults before using the machine
£lj(plug disconnected). Do not use a faulty
flex.
a 6. Keep the flex away from the cutting area.
cl37. Do not use the trimmer in wet weather
and do not use it to cut wet hedges.
8. Carry the trimmer by the handles provided
and keep hands away from the cutting blades.
9. In line with agricultural Trade Association
Regulations only persons over the age of
17 may work on their own with electric
hedge trimmers. Use is permitted for persons
over 16 years if the work is carried out
under the supervision of adults.
10. We would recommend that safety clothing
is worn during the work and that eyes,
ears, hair, hands and feet are fully protected.
Protective gloves should also be worn.
11. After switching off the hedge trimmer and
a before carrying out any cleaning, ensure
/!\that the motor cannot be switched on in¬
advertently by engaging the switch lock. In
any case, disconnect plug from mains
socket.
12. Check the cutting unit regularly for damage
and if damage is discovered, the cutting
unit should be properly repaired.
13. Be aware of your responsibility as user
towards third parties in the working area.
14. The trimmer must be properly checked and
serviced. If the blades get damaged they
should only be exchanged in pairs. In the
event of damage from impact, specialist's
inspection is essential.
15. Only use extension leads which have been
authorised for outside use. These flexes
must not be lighter than PVC covered flex
conforming to 227 IEC 53. They must be
water spray protected. If the flex has to be
changed, replace it only with authorised
flex H05 W F with centrally shaped plug to
fit sockets complying with IEC 320. Equip¬
ment which will be used in different outside
locations must be connected via residual
current-operated circuit breaker.
16. Ensure that the equipment is stored safely
after use in such a way that the blade can¬
not be touched.
17. When using the equipment, hold it securely
with both hands, stand firmly and ensure
that you have sufficient working space.
There should be no people, animals or
objects within the working area. Select the
cutting height so that the blade does not
make contact with the ground and you can
operate the equipment from a secure position.
18. Take care when transporting the equip¬
ment (only with blade cover!).
19. For initial use of the hedge trimmer we
would recommend that in addition to reading
the operating instructions, you also seek a
practical demonstration from an expert.
20. Always ensure that all protective devices
and handles are properly fitted. Never
attempt to use an incomplete machine.
21. The use of the hedgetrimmer is to be avoided
if other persons, above all children, are
within the working area.
22. Familiarize yourself with the working area
and pay attention to possible dangers
which you might not be able to hear due to
the noise of the machine.
5. Before Use_
Protective cover (Fig 1)
Loosen the two CM 6 x 12 screws fitted in the
base plate and remove. The enclosed protective
cover should be fitted to the base plate using
these two screws.
Assembly of the stirrup handle (Fig. 2)
Loosen the two screwed-in CM 6x16 screws and
remove. Insert the stirrup handle in the recess of
the hedge trimmer housing and, if necessary,
slightly separate the lower ends of the handle. To
secure the stirrup handle insert the two screws
GB-2