DCCconcepts Super Panel Setup page 7

DCC COMPATIBLE COMMAND CONTROL
LOC:8450 12:54AM
Step 6
FWD: 000
As before we always finish the command line with an END command, then the Super Panel knows
NCE
it has reached the end of this particular sequence. So press
DIRECTION
INC FAST
DEC FAST
PROG/ESC
Push the
Before you can run your program from the SuperPanel you need to reconnect the NCE system to
HORN/
the appropriate input on either the Super Panel or your faceplate. If you have two NCE PowerCab
WHISTLE
or ProCab handsets you can leave one handset connected to the faceplate or CAB BUS and one to
the PROGRAM port at all times, saving you from unplugging an plugging constantly.
OPTION
PowerCab Run Set Up
SELECT
LOCO
NCE PowerCab
DCC COMPATIBLE COMMAND CONTROL
DCC CONCEPTS V1.
Handset
SUPER PANEL 021
NCE CAB
DIRECTION MOMENTUM
1
SPEED
INC FAST INC
DEC FAST DEC
NCE PCP
HORN/
WHISTLE BELL HEADLIGHT Faceplate
EMERGENCY
STOP
OPTION RECALL
SELECT SELECT
LOCO MACRO ACCY
5
1 2 3 4
5 6 7 8
9 0 ENTER
CONSIST
SETUP CLEAR ADD DEL
PROG/
ESC EXPN 28/128 SHIFT
F10 F11 F12
9
6pin RJ12 Flat Cable
SETUP CLEAR
Cobalt iP Digital
Point Motor
Set to
Accessory
PROG/
Address 10
ESC
Once you become familiar with programming the Super Panel you may find it easier to write out
F10
the commands in tabular form so that you can check your logic. This can then be used to input
commands to the Super Panel quickly through the NCE keypad - see below for the keystrokes table
for SAMPLE 1.
Select the Input to Input 1
Step Keystrokes
1 1, 10, ENTER, ADD
2
L-----6
PROCAB
Press
MOMENTUM
THEN
Press
SPEED
ENTER
INC
DEC
key 4 times to return to the SET UP MENU SCREEN
BELL HEADLIGHT
EMERGENCY
STOP
RECALL
SELECT
MACRO ACCY
On-Off Toggle
Switch connected
to GND & Input 1
2 3 4
13.5V
PowerCab
PSU
6 7 8
0 ENTER
12V DC
6pin RJ12 Cable
CONSIST
CAB OUT
ADD DEL
EXPN 28/128 SHIFT
Track/Power Bus
F11 F12
0, ADD
DCCconcepts Super Panel Point Motor Control Manual V1.0 March 2024
0 to select END and press
INP:1 H STEP:2
0
END: PRESS ENTER
INP:1 H STEP:3
1=ACCY 2=MACRO >
Power Pro Run Set Up
18V Alpha Power PSU
If RE-SET light activates RE-SET
turn main power switch
off to re-set protection
Fully Protected 18V 5A DCC Power Supply
NCE Power Pro Base Unit
POWERPRO
NCE Corporation
FROM
CONTROL
CONTROL BUS BUS
PROGRAM
POWER TRACK TRACK
STATUS
16VAC / 28VDC MAX.
PUSH
CAB IN PROGRAM
Cobalt iP Digital
Point Motor
Set to
Accessory
Address 10
Input No 1
1, 1, ENTER, 1, ENTER
LOW Action
Accessory 10 Normal
End
On-Off Toggle
Switch connected
to GND & Input 1
DCC COMMAND STATION
with FIVE AMP POWER BOOSTER
CAB BUS
STATUS TRACK
PH-PRO
PUSH
12V DC
6pin RJ12 Cable
CAB OUT CAB IN PROGRAM
HIGH Action
Accessory 10 Reverse
End
ENTER.
DCC COMPATIBLE COMMAND CONTROL
LOC:8450 12:54AM
FWD: 000 L-----6
NCE PROCAB
DIRECTION MOMENTUM
SPEED
INC FAST INC
DEC FAST DEC
HORN/
WHISTLE
BELL HEADLIGHT
EMERGENCY
STOP
OPTION RECALL
SELECT SELECT
LOCO ACCY
MACRO
1 2 3 4
5 6 7 8
9 0 ENTER
CONSIST
SETUP CLEAR ADD DEL
PROG/
ESC EXPN 28/128 SHIFT
F10 F11 F12
NCE ProCab
Handset
6pin RJ12
Flat Cable
Track/Power Bus