Yamaha PLG150-DX Owner's Manual page 49

1.5 Pitch bend
This message conveys information on pitch bend operations.
Basically, this message is for changing the pitch of a part, but the depth of the fol-
lowing five effects can be controlled.
The effect of this message can be modified by the following parameters.
* Multi Part Parameter
1. BEND PITCH CONTROL
2. BEND FILTER CONTROL
3. BEND AMPLITUDE CONTROL
4. BEND LFO PMOD DEPTH
5. BEND LFO AMOD DEPTH
By default, the Pitch Control effect is applied.
If the Multi Part parameter Rcv PITCH BEND CHANGE = OFF, that part will
not receive pitch bend messages.
1.6 Channel aftertouch
This message conveys the pressure after the key is played on the keyboard (for an
entire MIDI channel). The pressure can be controlled for each part. This message
will affect the notes currently playing.
The effect of this message can be modified by the following parameters.
* Multi Part Parameter
1. CAT PITCH CONTROL
2. CAT FILTER CONTROL
3. CAT AMPLITUDE CONTROL
4. CAT LFO PMOD DEPTH
5. CAT LFO AMOD DEPTH
By default, there will be no effect.
If the Multi Part parameter Rcv CHANNEL AFTER TOUCH = OFF, that part
will not receive Channel Aftertouch.
1.7 Polyphonic aftertouch
This message conveys the pressure after the key is played on the keyboard (for
individual note numbers). The pressure can be controlled for each part. This mes-
sage will affect the notes currently playing.
The effect of this message is determined by the following Multi Part parameters.
l. PAT PITCH CONTROL
2. PAT AMPLITUDE CONTROL
3. PAT LFO PMOD DEPTH
4. PAT LFO AMOD DEPTH
By default, there will be no effect.
If the Multi Part parameter Rcv POLY AFTER TOUCH = OFF, that part will not
receive Polyphonic Aftertouch.
2. System exclusive messages
2.1 Parameter changes
This device uses the following parameter changes.
[ UNIVERSAL REALTIME MESSAGE ]
1) Master Volume
[ UNIVERSAL NON REALTIME MESSAGE ]
1) General MIDI System On
[ XG PARAMETER CHANGE]
1) XG System on
2) XG System parameter change
3) Multi Part parameter change
[ PLG150-DX NATIVE PARAMETER CHANGE ]
1) PLG150-DX System parameter change
2) PLG150-DX Multi Part parameter change
[ DX PARAMETER CHANGE ]
1) VCED parameter change
2) ACED parameter change
2.1.1 Universal realtime messages
2.1.1.1 Master Volume
11110000 F0H
7FH
01111111
7FH
01111111
00000100 04H
01H
00000001
* 0sssssss SSH
TTH
0ttttttt
11110111 F7H
F0H
11110000
7FH
01111111
0xxxnnnn XNH
04H
00000100
00000001 01H
SSH
0sssssss
TTH
0ttttttt
F7H
11110111
= Exclusive status
= Universal Real Time
= ID of target device
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
= Exclusive status
= Universal Real Time
= Device Number, xxx = don't care
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
When received, the Volume MSB is reflected in the System Parameter MAS-
TER VOLUME.
* The binary expression 0sssssss is expressed in hexadecimal as SSH.
The same applies elsewhere.
2.1.2 Universal non-realtime messages
2.1.2.1 General MIDI System On
F0H = Exclusive status
11110000
7EH = Universal Non-Real Time
01111110
01111111 7FH = ID of target device
09H = Sub-ID #1=General MIDI Message
00001001
00000001 01H = Sub-ID #2=General MIDI On
F7H = End of Exclusive
11110111
or
F0H = Exclusive status
11110000
7EH = Universal Non-Real Time
01111110
0xxxnnnn XNH = N:Device Number, X:don't care
09H = Sub-ID #1=General MIDI Message
00001001
00000001 01H = Sub-ID #2=General MIDI On
F7H = End of Exclusive
11110111
When this message is received, the SOUND MODULE MODE is set to XG,
and all data except for MIDI Master Tuning will be restored to the default
value.
However this message will not be received when SOUND MODULE MODE
= C/M.
Since approximately 50ms is required to process this message, be sure to
allow an appropriate interval before sending the next message.
2.1.3 XG Parameter Change
This message sets XG-related parameters. Each message can set a single
parameter.
The message format is as follows.
11110000 F0H Exclusive status
43H YAMAHA ID
01000011
1NH N:device Number
0001nnnn
01001100 4CH Model ID
GGH Address High
0ggggggg
0mmmmmmm MMH Address Mid
LLH Address Low
0lllllll
0vvvvvvv VVH Data
: :
F7H End of Exclusive
11110111
For parameters whose Data Size is 2 or 4, the appropriate amount of data will
be transmitted as indicated by Size.
2.1.3.1 XG System On
F0H Exclusive status
11110000
43H YAMAHA ID
01000011
0001nnnn 1NH N:device Number
4CH Model ID
01001100
00000000 00H Address High
00H Address Mid
00000000
01111110 7EH Address Low
00H Data
00000000
F7H End of Exclusive
11110111
When ON is received, the SOUND MODULE MODE changes to XG.
Since approximately 50ms is required to process this message, be sure to
allow an appropriate interval before sending the next message.
2.1.3.2 XG System parameter change
This message sets the XG SYSTEM block (see Tables <1-1> and <1-2>).
2.1.3.3 Multi Part parameter change
This message sets the Multi Part block (see Tables <1-1> and <1-3>).
2.1.4 PLG150-DX Native parameter change
This message sets parameters unique to the PLG150-DX.
Each message can set a single parameter. The message format is as follows.
11110000 F0H Exclusive status
43H YAMAHA ID
01000011
0001nnnn 1NH N:Device Number
62H Model ID
01100010
GGH Address High
0ggggggg
MMH Address Mid
0mmmmmmm
LLH Address Low
0lllllll
0vvvvvvv VVH Data
: :
11110111 F7H End of Exclusive
For parameters whose Data Size is 2 or 4, the appropriate amount of data will
be transmitted as indicated by Size.
MIDI Data Format
:
:
49