Registered Parameter Number; Non-Registered Parameter Number; System Real Time Messages; System Exclusive Message - Yamaha MOTIF 6 Data List

(3-3) REGISTERED PARAMETER NUMBER

STATUS 1011nnnn(BnH)
LSB 01100100(64H)
RPN LSB 0ppppppp
MSB 01100101(65H)
RPN MSB 0qqqqqqq
DATA ENTRY MSB 00000110(06H)
DATA VALUE 0mmmmmmm
DATA ENTRY LSB 00100110(26H)
DATA VALUE 0lllllll
First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB.
RPN D.ENTRY
LSB MSB MSB LSB PARAMETER NAME
00H 00H mmH --- PITCH BEND SENSITIVITY
01H 00H mmH llH MASTER FINE TUNE
02H 00H mmH --- MASTER COARSE TUNE
7FH 7FH --- --- RPN RESET
RPN numbers will be left not designated.
The internal values are not affected.

(3-4) NON-REGISTERED PARAMETER NUMBER

There are no applicable parameters.
These are transmitted to the Plug-in board.

(3-5) SYSTEM REAL TIME MESSAGES

(3-5-1) ACTIVE SENSING
STATUS 11111110(FEH)
Transmitted at every 200 msec.
Once this code is received, the instrument starts sensing. When no status nor data is received for over approximately
350 ms, MIDI receiving buffer will be cleared, and the sounds currently played and the sustain switch are forcibly
turned off. In this case, each control data will be reset to a certain value.

(3-6) SYSTEM EXCLUSIVE MESSAGE

(3-6-1) UNIVERSAL NON REALTIME MESSAGE
(3-6-1-1) GENERAL MIDI MODE ON
F0H 7EH 7FH 09H 01H F7H
Received only when SYSTEM Receive GM/XG on is set to on in PERFORMANCE MODE. The Part values will be reset
according to the SYSTEM Internal Part settings.
(3-6-1-2) IDENTITY REQUEST (Receive only)
F0H 7EH 0nH 06H 01H F7H ("n" = Device No.However, this instrument receives under "omni.")
(3-6-1-3) IDENTITY REPLY (Transmit only)
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H 7FH F7H
dd;Device Number Code
MOTIF6: 7C 04
MOTIF7: 7D 04
MOTIF8: 7E 04
(3-6-2) UNIVERSAL REALTIME MESSAGE
(3-6-2-1) MIDI MASTER VOLUME
F0H 7FH 7FH 04H 01H llH mmH F7H
Sets the MASTER VOLUME value.
The value "mm" is used to set the master volume (the value "ll" should be ignored).
(3-6-3) PARAMETER CHANGE
(3-6-3-1) XG SYSTEM ON
11110000 F0
01000011 43
0001nnnn 1n
01001100 4C
0aaaaaaa 0A
0aaaaaaa 0A
0aaaaaaa 7E
0 0
11110111 F7
Received only when SYSTEM Receive GM/XG on is set to on in PERFORMANCE MODE. The Part values will be reset
according to the SYSTEM Internal Part settings.
Be aware that executing this message takes ca. 170ms and that, therefore, a certain interval before executing the
following message is needed.
(3-6-3-2) NATIVE PARAMETER CHANGE, MODE CHANGE
11110000 F0
01000011 43
0001nnnn 1n
01101011 6B
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0ddddddd ddddddd
| |
11110111 F7
For parameters with data size of 2 or more, the appropriate number of data bytes will be transmitted.
See the following MIDI Data Table for Address and Byte Count.
Always received no matter which device number is selected, in the case of REMOTE SWITCH.
n = 0~15 CHANNEL NUMBER
p = RPN LSB (Refer to the table as shown below)
q = RPN MSB (Refer to the table as shown below)
m = Data Value
l = Data Value
DATA RANGE
00H - 18H (0 - 24 semitones)
{mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH}
(-8192*100/8192) - 0 - (+8192*100/8192)
28H - 40H - 58H (-24 - 0 - +24 semitones)
Exclusive status
YAMAHA ID
device Number
Model ID
ddress High
ddress Mid
Address Low
Data
End of Exclusive
Exclusive status
YAMAHA ID
device Number
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
(3-6-4) BULK DUMP
11110000 F0
01000011 43
0000nnnn 0n
01101011 6B
0bbbbbbb bbbbbbb
0bbbbbbb bbbbbbb
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0 0
| |
0ccccccc ccccccc
11110111 F7
See the following MIDI Data Table for Address and Byte Count.
The Check sum is the value that results in a value of 0 for the lower 7 bits when the Byte Count, Start Address, Data
and Check sum itself are added.
(3-6-5) DUMP REQUEST
11110000 F0
01000011 43
0010nnnn 2n
01101011 6B
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
11110111 F7
See the following MIDI Data Table for Address and Byte Count.
(3-6-6) PARAMETER REQUEST
11110000 F0
01000011 43
0011nnnn 3n
01101011 6B
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
11110111 F7
See the following MIDI Data Table for Address and Byte Count.
(4) SYSTEM OVERVIEW (Keyboard, Sequencer and Tone
Generator)
The optional mLAN board can be installed to the MOTIF.
Although three types of note on/note off data, received via MIDI, played by the internal sequencer and played on the
keyboard will be distinguished, the other controllers (channel messages) equally affect the entire notes.
ALL SOUND OFF clears all the sounds in the specific channel(s) played by both the keyboard and the data via MIDI.
ALL NOTES OFF received via MIDI clears the sounds in the specific channel(s) played via MIDI.
45
Exclusive status
YAMAHA ID
device Number
Model ID
Byte Count
Byte Count
Address High
Address Mid
Address Low
Data
Check-sum
End of Exclusive
Exclusive status
YAMAHA ID
device Number
Model ID
Address High
Address Mid
Address Low
End of Exclusive
Exclusive status
YAMAHA ID
device Number
Model ID
Address High
Address Mid
Address Low
End of Exclusive