CONTENTS Safety instruction………………………………………………………………………1 General instruction……………………………………………………………………….1 Alignment instruction……………………………………………………………………2 Alignment f low ..……………………… ……………………… ……………………..2 A l i g n m e n t m e t h o d … … … … … … … … … … … … … … … … … … … … … … … … … . .3 Block diagram..………………………………………………………………………...10 MAIN IC………………………………………………………………………………..11 P a r t s l i s t …...
Note: This service manual is only for professional service personnel’s reference. Before servicing the unit, please read the following items carefully. 1 Safety instruction 1.1 X-RAY radiation precaution 1.1.1 Excessive voltage will cause harmful X-ray. To avoid this radiation hazard, the high voltage should fall within the limitation.
Alignment instruction 3.1 Debugging item a)adjust mode instruction b)B+ voltage adjustment c)RFAGC voltage adjustment d)focus adjustment e)Screen-grid voltage white balance, sub brightness adjustment f)filed scan center, line , amplitude adjustment g)H-scan center adjustment 3.2 Alignment flow PROM copy High voltage check B+ adjustment X-ray protect check Filament voltage check...
3.3 Enter/exit factory adjustment method Use remote control, press “MENU” button, then press 6483,”TEST”will appear on screen to show that you have entered the factory adjustment method, press “STANDBY” to exit it. Use factory remote control, press the “PRESET” and “TEST” button, then the screen display “test” which means you have entered into the factory adjustment mode, press the “TEST”...
Page 6
b) adjust focus electrode potentiometer on FBT to optimize B area focus of screen. 4.7 White balance adjustment (color temperature 12000°K± 8MPCD,X=0.270± 0.008,Y=0.283± 0.008) a) receive full white signal, set color is 0 b) select factory menu3 c) on the basis of blue gun ”BD”, select and adjust “RD, GD” item to make white balance respectively at brightness Y=6cd/m , Y=80cd/m meet standard (color temperature 12000°K±...
Page 7
place. c) Exit factory menu 4.12. Checking point 4.12.1 High voltage check Connect High Voltage meter between CRT second anode and GND. Receive A7 signal, set the control to “STANDARD”, measure the high voltage value, the reading should be 25 kV±0. 5 kV Set the brightness and contrast to miminum (zero beam current), measure the high voltage, the reading should not exceed 27kV.
Page 8
4.14 Color purity correction a) Turn on your TV b) At least 15 minutes later, use anti-magnetized coil for degaussing c) Obtain maximum brightness and contrast d) Select factory menu3 and adjust to let R and B be zero, then let only green raster appear on the screen at the moment e) Loosen screws of deflection yoke frame to let vertical green belt appear on screen only Move the rubber wedge...
Page 9
4.16.2 turn on the unit in the STANDBY state Press CH+/CH- buttons turn on in the STANDBY state. 4.16.3 Information of software version Enter MEU9 of the factory menu in the top. 4.16.4 “STANDARD”, “COLORFUL” and “ SOFTNESS” a).Enter MENU5 Mode of the factory menu b).charge their for seemly analog quantity, then return standard option.
Page 10
BTSC-A1 0-31 BTSC-A2 0-31 BTSC-TC BTSC-STS BTSC-ADJ MODE STANADARD(standard, soft, floweriness) BRIGHT 0-100 0-100 CONTRAST COLOR 0-100 SCBRIGHT 0-63 YDELAYTV 0-15 YDELAYAV 0-15 1(field over-scan switch) AGCSPEED 1(AGC of speed) 0(IF PLL SPEED) FMWS 1(frequency range of sound OFF=225KHZ,ON=450KHZ) 0(pre-shock and over-shock scale) NTSCMATRIX USA/JAPAN VOLPIN...
Page 11
STARTTIME 6-15 8(turn on time) IF OFFSET 0-63 32(IF compensate) TUNER OPTION 0(BXATB011F---X/ BXATB108F---K) 1 (BXATB017F---K) 2(XXX) GAME GALENDA...
Block diagram A101 Z301 V801 TDA8377 video TUNER IF IN Y IN BU4052 video RF AGC V IN V352 N121 U IN video CVBSINT video S-VHS CHROMA IFVO OUT TRAP video CVBS/Y IN audio AN702 24C08 ARi2 ARi1 AUDIO OUT RGB OUT N801 BU4052...
MAIN IC 8377: ICs functional description UOC TDA(OM)8377 SYMBOL DESCRIPTION STAND BY output. In STAND BY mode, high level (Power OFF). For Power ON this pin will be reduced to low. C-bus clock line C-bus data line TUNING P3.0/NTSC SW Control keys input Sound Volume control PWM output MUTE...
Page 14
DECDIG decoupling digital supply of TV-processor PH2LF Phase-2 filter PH1LF Phase-1 filter GND3 Ground 3 for TV-processor DECBG Band gap decoupling AVL/EWD Automatic volume leveling /EAST-WEST drive output VDRB Vertical drive B output VDRA Vertical drive A output IFIN1 IF input 1 IFIN2 IF input 2 IREF...
Page 18
PART LIST PART# DESCRIPTION LOCA.NO. 203-TK20500-12 TS2050J, PRIMA BRAND JENSEN,N- 100-TK20500-01 TK2050 123-30001-04 TWIST WIRE 655-62101-01 (6-PINS) LEAD WITH HOUSING 700-60151-00 LED LED COLUMN 700-60152-00 LED LED COLUMN 742-30005-09 LINE TIE 742-30006-09 GRADING TIE 742-30029-00 POWER CORD CLASPER 742-30032-00 742-30032-00...
Page 19
POWER SYMBOL LABEL ( JENSEN) 881-63758-00 BAR CODE LABEL (69020712050) 881-80666-00 REGISTER CARD ( JENSEN AMERICA ) 881-80679-00 SERVICE CARD ( AMERICA 20-24 CRT) 886-31132-121 CARTON BOX (TS2050J,JENSEN) 887-21135-00 CLASPER PALSTIC BAG 230X330X0.1 887-21135-02 CLASPER PALSTIC BAG 230X330X0.1 615-20429-00 SPEAKER ASS'Y 384-40308-40...
Page 36
TK2050 PART LIST OF EXPLODED VIEW DESCRIPTION PART# PORT BAFFLE 808-6B758-04 REAR CABINET 780-10915-J40A SCREW 851-24020-14 POWER LINE CLASP 742-30029-00 MAIN BOARD ASSY 667-TKP50-01A 335-21225-00U CRT FIXED BLOCK 868-20472-00D CRT SUPPORT 868-20491-00 SCREW 851-53010-11 RIGHT LEAD TRACK 870-20846-00 SPEAKER BRACKET 870-20849-00 SIDE AV BRACKET 870-20843-40...
SCHEMATIC DIAGRAM are extremely CAUTION:all the parts in the schematic diagram marked with shodows and the signs of important for safety. In case of replacement of any part of components. Be sure to consult the service manual carefully. 1. the schematic diagram is characteristic. The various valus in the electric circuits are basic data, which are changeable according to the various basic circuits.