CONTENTS Safety instruction………………………………………………………………………1 General instruction……………………………………………………………………….1 Alignment instruction……………………………………………………………………2 Alignment f low ..……………………… ……………………… ……………………..2 A l i g n m e n t m e t h o d … … … … … … … … … … … … … … … … … … … … … … … … … . .3 BLOCK DIAGRAM………………………………………………………………………...
Note: This service manual is only for professional service personnel’s reference. Before servicing the unit, please read the following items carefully. 1 safety instruction 1.1 X-RAY radiation precaution 1.1.1 Excessive voltage will cause harmful X-ray. To avoid this radiation hazard, the high voltage should fall within the limitation.
3.1 Debugging item a)adjust mode instruction b)B+ voltage adjustment c)RFAGC voltage adjustment d)focus adjustment e)Screen-grid voltage white balance, sub brightness adjustment f)filed scan center, line , amplitude adjustment g)H-scan center adjustment 3.2 Alignment flow Normal +B adjustment Focus adjustment AGC adjustment temperature aging White balance...
Page 5
b) under ”M” condition, set the accelerator to an appropriate point for aging. 4.4 Accelerator adjustment a) do not receive signals; b) select “SC” of factory menu3 to let the field scanning stop working. c) adjust acceleration potentiometer to let bright lines just appears on screen. d) exit SC menu.
Page 6
g) Adjust VR431 to minimize trapezoidal distortion h) Exit factory menu Fig-3 line scan adjustment 4.10 Sub-brightness adjustment a) Receive PAL-D/K PHILIPS signal b) Select “SB” of factory menu3 c) Adjust “SB” to let things between the sixth and seventh grey scale clear 4.11 OSD adjustment a) Receive PAL-D/K PHILIPS signal b) Select OSD H and OSD V of factory menu4.
Page 7
b) At least 15 minutes later, receive square test pattern signal c) Adjust brightness and contrast to get the best picture d) Adjust the angle of two tetrode magnetic rings to let the red vertical line coincide with the blue vertical line at middle of screen e) Keep the angle unchanged, move the two tetrode magnetic rings at the same time to let the red and blue horizontal lines coincide at middle of screen...
Page 8
75(adjust white balance of brightness contrast) 32(red cut off level adjustment) 32(green cut off level adjustment) 32(red cut off level adjustment) 32(green cut off level adjustment) 32(blue cut off level adjustment) 40(sub brightness adjustment) OSD.V.POSITION 10(OSD position) OSD.H.POSITION 5(OSD H-position) BTSC-MODE MONO(STEORO,SAP ) BTSC-ST...
Page 9
VOLADJPOING 1(volume value have:1,25,50,75) VOLVALUE 20(volume curve value:20,60,75,90) CATHOOELEVEL 7(cathode level) UOCVOLUME 0(0:PWM terminal control; 1:UOC sound amplitude control of inside) FMATT 45(UOC sound output of amplitude) BTSC : 38 COMBFILTRE 0(N comb filter) HEADPHONE 0(earphone function selection) VM OPTION 0(VM function selection) FRANCE 1 French...
Block diagram TDA8377 video TUNER IF IN Y IN RF AGC V IN 4052 video U IN CVBSINT video S-VHS video CHROMA IFVO OUT TRAP video CVBS/Y IN audio 24C08 ARi2 ARi1 AUDIO OUT RGB OUT N801 BU4052 V OUT H OUT ALi2 ALi1...
MAIN IC 8377: ICs functional description UOC TDA8377 SYMBOL DESCRIPTION STAND BY output. In STAND BY mode, high level (Power OFF). For Power ON this pin will be reduced to low. C-bus clock line C-bus data line TUNING tuning Voltage (Vt) PWM output P3.0/NTSC SW Port 3.0 or NTSC output/SCART SW input, Forced NTSC selection, Low-level output, otherwise High output.
Page 12
Sound Volume control PWM output MUTE Sound mute output VSSC/P Digit ground for µ-controller core and periphery BAND1 Tuner Band selection output BAND2 Tuner Band selection output VSSA Analog ground of teletext decoder and digital ground of TV-processor SECPLL SECAM PLL decoupling supply voltage TV-processor(+8V) DECDIG decoupling digital supply of TV-processor...
Page 13
R2/VIN 2nd R input / V (R-Y) input / PR input G2/YIN 2nd G input / Y input B2/UIN 2nd B input / U (B-Y) input / PB input BCLIN beam current limiter input BLKIN black current input / V-guard input Red output Green output Blue output...
Page 14
Test point Waveforms 1.2Vpp 2.6Vpp 3.8Vpp 2.5Vpp 2.5Vpp TDA8377 TDA8377 TDA8377 TDA8377 TDA8377 PIN51 0.9Vpp 5Vpp 95Vpp 95Vpp 95Vpp TDA8377 PIN34 TDA8377 CRT KR CRT KG CRT KB 0.8Vpp 1Vpp 2.7Vpp 1000Vpp V451 B V451 C TDA8377 TDA8377 TDA8377 22Vpp 300Vpp T511 PIN7 IC voltages...
Page 30
667-TK2525-29A SIDE AV BOARD ASS'Y 364-93202-00 AV JACK AV306-2 XAA1 655-6E301-24 (6-PINS) LEAD WITH HOUSING XAA3 782-Q2455-2900 SIDE AV PCB 808-6B786-07 AV BAFFLE (SILK-SCREEN ) 851-53010-31 SCREW SJ2825 ST3X10FT-D.Zn 868-10043-00 WASHER (14X4X1 METAL) 870-20843-01 SIDE AV BRACKET ( MOLD DARK GRAY ) JUMPER WIRE LAA1 JUMPER WIRE...
Page 33
TK2426 PART LIST OF EXPLODED VIEW DESCRIPTION PART# SCREW 851-24020-14 CRT BOARD No number RUBBER RING 785-30002-13B 335-2512D-00U SCREW 851-53008-31 SPEAKER 384-40908-B0 WASHER 868-20217-00 SPEAKER BRACKET 870-20700-00A STANDBY BUTTON BOARD 667-TK24261-05 ASSEMBLY BUTTON CAP 877-60560-00 BUTTON BOARD ASSEMBLY 667-TK2426-05 LED COLUMN 700-60160-00 FRONT CABINET 611-D26X0J0H2B...
Page 34
SCHEMATIC DIAGRAM CAUTION:all the parts in the schematic diagram marked with shodows and the signs of are extremely important for safety. In case of replacement of any part of components. Be sure to consult the service manual carefully. 1. the schematic diagram is characteristic. The various valus in the electric circuits are basic data, which are changeable according to the various basic circuits.