CONTENTS Safety instruction………………………………………………………………………1 General instruction……………………………………………………………………….1 Alignment instruction……………………………………………………………………2 Alignment f low ..……………………… ……………………… ……………………..2 A l i g n m e n t m e t h o d … … … … … … … … … … … … … … … … … … … … … … … … … . .3 Block diagram..………………………………………………………………………...10 MAIN IC………………………………………………………………………………..11 E l e c t r i c a l p a r t s l i s t …...
Note: This service manual is only for professional service personnel’s reference. Before servicing the unit, please read the following items carefully. 1 Safety instruction 1.1 X-RAY radiation precaution 1.1.1 Excessive voltage will cause harmful X-ray. To avoid this radiation hazard, the high voltage should fall within the limitation.
Alignment instruction 3.1 Debugging item a)adjust mode instruction b)B+ voltage adjustment c)RFAGC voltage adjustment d)focus adjustment e)Screen-grid voltage white balance, sub brightness adjustment f)filed scan center, line , amplitude adjustment g)H-scan center adjustment 3.2 Alignment flow PROM copy High voltage check B+ adjustment X-ray protect check Filament voltage check...
3.3 Enter/exit factory adjustment method Use remote control, press “MENU” button, then press 6483,”TEST”will appear on screen to show that you have entered the factory adjustment method, press “STANDBY” to exit it. Use factory remote control, press the “PRESET” and “TEST” button, then the screen display “test” which means you have entered into the factory adjustment mode, press the “TEST”...
Page 6
b) adjust focus electrode potentiometer on FBT to optimize B area focus of screen. 4.7 White balance adjustment (color temperature 12000°K± 8MPCD,X=0.270± 0.008,Y=0.283± 0.008) a) receive full white signal, set color is 0 b) select factory menu3 c) on the basis of blue gun ”BD”, select and adjust “RD, GD” item to make white balance respectively at brightness Y=6cd/m , Y=80cd/m meet standard (color temperature 12000°K±...
Page 7
place. c) Exit factory menu 4.12. Checking point 4.12.1 High voltage check Connect High Voltage meter between CRT second anode and GND. Receive A7 signal, set the control to “STANDARD”, measure the high voltage value, the reading should be 25 kV±0. 5 kV Set the brightness and contrast to miminum (zero beam current), measure the high voltage, the reading should not exceed 27kV.
Page 8
4.14 Color purity correction a) Turn on your TV b) At least 15 minutes later, use anti-magnetized coil for degaussing c) Obtain maximum brightness and contrast d) Select factory menu3 and adjust to let R and B be zero, then let only green raster appear on the screen at the moment e) Loosen screws of deflection yoke frame to let vertical green belt appear on screen only Move the rubber wedge...
Page 9
4.16.2 turn on the unit in the STANDBY state Press CH+/CH- buttons turn on in the STANDBY state. 4.16.3 Information of software version Enter MEU9 of the factory menu in the top. 4.16.4 “STANDARD”, “COLORFUL” and “ SOFTNESS” a).Enter MENU5 Mode of the factory menu b).charge their for seemly analog quantity, then return standard option.
Page 10
BTSC-A1 0-31 BTSC-A2 0-31 BTSC-TC BTSC-STS BTSC-ADJ MODE STANADARD(standard, soft, floweriness) BRIGHT 0-100 0-100 CONTRAST COLOR 0-100 SCBRIGHT 0-63 YDELAYTV 0-15 YDELAYAV 0-15 1(field over-scan switch) AGCSPEED 1(AGC of speed) 0(IF PLL SPEED) FMWS 1(frequency range of sound OFF=225KHZ,ON=450KHZ) 0(pre-shock and over-shock scale) NTSCMATRIX USA/JAPAN VOLPIN...
Page 11
STARTTIME 6-15 8(turn on time) IF OFFSET 0-63 32(IF compensate) TUNER OPTION 0(BXATB011F---X/ BXATB108F---K) 1 (BXATB017F---K) 2(XXX) GAME GALENDA...
Block diagram A101 Z301 V801 TDA8377 video TUNER IF IN Y IN BU4052 video RF AGC V IN V352 N121 U IN video CVBSINT video S-VHS CHROMA IFVO OUT TRAP video CVBS/Y IN audio AN702 24C08 ARi2 ARi1 AUDIO OUT RGB OUT N801 BU4052...
MAIN IC 8377: ICs functional description UOC TDA(OM)8377 SYMBOL DESCRIPTION STAND BY output. In STAND BY mode, high level (Power OFF). For Power ON this pin will be reduced to low. C-bus clock line C-bus data line TUNING P3.0/NTSC SW Control keys input Sound Volume control PWM output MUTE...
Page 14
DECDIG decoupling digital supply of TV-processor PH2LF Phase-2 filter PH1LF Phase-1 filter GND3 Ground 3 for TV-processor DECBG Band gap decoupling AVL/EWD Automatic volume leveling /EAST-WEST drive output VDRB Vertical drive B output VDRA Vertical drive A output IFIN1 IF input 1 IFIN2 IF input 2 IREF...
Page 18
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION "SAFETY PRECAUTION" AND "COMPONENTS SAFETY NOTICE" ON PAGE 1 OF THIS MANUAL. CAUTION: 1. The shaded areas makes in the schematic diagram and the parts list designate componentswhich have special characteristics important for safety and should be replaced only with type identical tothose in the original circuit or specified in the parts list.
Page 50
TK2026 exploded views list DESCRIPTION DESCRIPTION SCREW POWER KEY CRT BOARD FRONT CABIET SCREW SUPPORT MAIN BOARD ASSY THREDAD CLASP MAIN BOARD SCREW CRT FIXER SPEAKER BRAIDED PULLING SPRING RUBBER WASHER DEGAUSSING COIL SPEAKER BRACKET THREDAD CLASP SUPPORT SIDE AV...
Page 54
TK2053 exploded views list DESCRIPTION DESCRIPTION LABEL BUTTON BOARD SCREW MAIN BOARD SCREW POWER COIL SCREW CRT FIXER BRAIDED PULLING SPRING LIGHT-TOUCH SWITCH BRAIDED PULLING SCREW THREDAD CLASP SPEAKER DEGAUSSING COIL SPEAKER SUPPORT CRT BOARD ASSY FRONT CABINET REAR CABINET LED COLUMN SIDE AV SUPPORT DECORATION PIECE...
SCHEMATIC DIAGRAM are extremely CAUTION:all the parts in the schematic diagram marked with shodows and the signs of important for safety. In case of replacement of any part of components. Be sure to consult the service manual carefully. 1. the schematic diagram is characteristic. The various valus in the electric circuits are basic data, which are changeable according to the various basic circuits.
Need help?
Do you have a question about the TK2026 and is the answer not in the manual?
Questions and answers