CONTENTS X-RAY RADIATION PRECAUTION………………………………………………………1 SAFETY PRECAUTION…………………………………………………………………..1 PRODUCT SAFETY NOTICE…………………………………………………………….2 INSTALLATION AND SERVICE ADJUSTMENTS………………………………………3 GENERAL INSTRUCTION…………………………………………………………………3 ALIGNMENT ITEMS AND PROCEDURE………………………………………………..3 FACTORY ADJUSTMENT MODE…………………………………………………………4 CHECKING POINT……………………………………………………………………………5 PRESET THE FOLLOWING IN FACTORY…………………………………………………6 FACTORY MENU………………………………………………………………………………6 CONVERGENCE MAGNET ASSEMBLY POSITIONING……………………………..8 COLOR PURITY ADJUSTMENT…………………………………………………………..8 CONVERGENCE ADJUSTMENT…………………………….……………………………..8 CENTER CONVERGENCE ADJUSTMENT …………………………………………..8 CIRCUMFERENCE CONVERGENCE ADJUSTMENT ……………………………..9 USA CHANNEL FREQUENCY TABLE (181 CH)………………………………………...
SAFETY INSTRUCTION Before servicing and aligning this equipment, please read the following “X-RAY RADIATION PRECAUTION” ,“SAFETY PRECAUTION” and “PRODUCT SAFETY NOTICE”. X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially hazardous X-RAY RADIATION. To avoid such hazards, the high voltage must not be above the specified limit. The normal value of the high voltage of this receiver is 26.5kV(20”) at zero beam current (minimum brightness) under 220V AC power source.
8) Before returning the set to your customer, always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, screwheads, metal overlays, control shafts etc. to be sure the set is safe to operate without danger of electrical shock. Plug the AC line cord directly into a 220V AC outlet (do not use a line isolation transformer during this check).
3) Connect the power plug to AC 220V/50Hz, turn on the power switch, wait for normal raster, Check B 110V±0.2V. Test point B1-5V B2-8V B3-10V B4-32V TH-12V TH-20V TH-200V DC(V) 20(22) INSTALLATION AND SERVICE ADJUSTMENTS GENERAL In the majority of cases, a color television receiver will need only slight touch – up adjustment upon installation.
EEPROM copy High voltage check B+ check X-ray protection check Filament voltage check RFAGC adjustment Picture and sound check FOCUS Sub-brightness check Screen-grid voltage White balance adjustment White balance check Scanning amplitude center & Color purity 、 convergence check raster correction adjustment AV terminal check Check The TV set &...
white balance basically normal. 4.2 Set the color to 0, contrast to 10, use oscilloscope to adjust CRT’s red gun’s waveform (see below figure), adjust brightness to make the seventh step’s (the darkest) DC level be 180V, adjust accelerating electrode to make the seventh step slightly light up (just can separate the seventh step and below dark field).
4. Picture and sound check 4.1 Receive standard TV signal. 4.2 Making use of picture control buttons to check color,contrast,brightness,sharpness,tint’s control function. 4.3 Making use of sound control buttons to check volume control function. 5. Sub-brightness check Receive D-8 signal, set color ,contrast,brightness all to 0, picture’s left side first grid slightly lights. 6.
Page 9
Appendix 1 FACTORY MENU FACTORY MENU 1:VDJ ADJ 1. VIF VCO AUTO ADJ OFF VIF VCO auto adjustment 2. RF DELAY ADJ TUNER AGC adjustment 3. S-TRAP ADJ S-TRAP auto adjustment 2: RASTER ADJ 1. V-POSITION Vertical position adjustment(PAL) 2. V-SIZE Vertical size adjustment 3.
13. SECAM BGP 14. VIDEO OUTGAIN Demodulation output range adjustment 15. OM DET Over modified detecting on/off 16. S-SLICE DOWN Sync detecting slice stage 17. AUTO SLICE DN Auto detecting on/off 18. V SYNC DET Vertical sync detecting 19. V-1 WINDOW 20.
8. Check the purity of the red and blue raster. 9. Obtain a white raster, referring to “CRT WHITE BALANCE ADJUSTMENT”. 10. Proceed with convergence adjustment. FIG.3 CONVERGENCE ADJUSTMENT NOTE: Before attempting any convergence adjustments, the receiver should be operated for at least fifteen minutes.
Page 12
6. Keep the yoke position and put another wedge in either upper space. Remove cover paper and stick the wedge on the picture tube to fix the yoke. 7. Detach the temporarily mounted wedge and put it in another upper space. Stick it on the picture tube to fix the yoke.
PART LIST PART# DESCRIPTION LOCA.NO. 100-M20190-11 TS2019 100-M20190-01 M2019 123-30001-04 TWIST WIRE 384-40316-Q0 SPEAKER ST511-01 477-12105-00 DEGAUSS COIL DX-56-2 655-21201-128 (2-PINS) LEAD WITH HOUSING 808-1D550-01 INTERFACE SPACE PLATE (SILK-SCREEN ) 665-62101-01 (6-PINS) LEAD WITH HOUSING 700-60127-00 LED COLUMN 741-10001-02 WIRE FIXED BLADE...
Page 21
488-10012-00 BATTERY 7#( made in china 604-M20196-00 OWNER'S MANUAL(PRIMA AMERICA ) 880-10589-A1 FRONT LOGO (PRIMA SILVERY GREY 10C 21" 880-10205-757 BACK PLATE (TS2019,PRIMA) 881-63016-00A POWER SYMBOL LABEL (T2751) 881-63633-00 UPCBAR CODE LABEL (69020752019) 881-80665-00 REGISTER CARD (PRIMA AMERICA ) 881-80679-00 SERVICE CARD (...
Need help?
Do you have a question about the TS2019 and is the answer not in the manual?
Questions and answers