Advertisement
Quick Links
Wiring/Amplifier Installation Guide
Model:
Description:
Part Number:
Assembly Time:
Before you beign, read thought these instructions and check that
all parts are present. Please note that MB Quart cannot assume any
responsibility for damage resulting from incorrect installation.
No.
1
NA2-400.2RC
2
NA2-400.1
3
Amplifier Mounting Plate
4
Harnesses
1
Bojo or Panel Tool
2
Philips Screwdriver
3
8, 10, 13mm Socket
4
Rachet
5
T25 Torx Bit
6
T50 Torx Bit
Jeep JL (Wrangler) & JT (Gladiator)
Wiring/Amplifier Install
MBQJ-ACC-1 & MBQJ-ACC-1AH
120 Minutes (2 Hours)
Parts List
Component Name
Tools Required
Page 1 of 23
Qty
2
1
1
4
Advertisement
Related Manuals for MB QUART NA2-400.2RC
Summary of Contents for MB QUART NA2-400.2RC
- Page 1 Part Number: 120 Minutes (2 Hours) Assembly Time: Before you beign, read thought these instructions and check that all parts are present. Please note that MB Quart cannot assume any responsibility for damage resulting from incorrect installation. Parts List Component Name NA2-400.2RC...
- Page 2 Disassembly Step 1 ● To get to this point will be Step 1 to 4 from the speaker installation Remove (5) Phillips screws from center dash/screen area Step 2 ● Unclip lower center console and move toward rear of vehicle Step 3 ●...
- Page 3 Disassembly Step 4 ● Route T-Harness pigtail from radio pocket to lower console behind metal brace Step 5 ● Continue routing pigtail harness toward glovebox opening (this will be where the main control box will be hidden) Step 6 ● Unclip passenger kick panel cover Page 3 of 23...
- Page 4 Disassembly Step 7 ● Disconnect passenger door harness, door strap, and 10mm nut that has been exposed Step 8 ● Unclip passenger sill cover, it is easiest starting at the rear of the door opening and moving forward, once unclipped remove from vehicle Step 9 ●...
- Page 5 Disassembly Step 10 ● Slide passenger seat forward and remove (2) T-50 Torx bolts from the rear Note Do not remove seat from vehicle Step 11 ● Remove front two roof sections (which will aid in soundbar disassembly to follow) and refer to your Jeep owner manual on removal of top Step 12...
- Page 6 Disassembly Step 13 ● Unclip and disconnect the dome light Step 14 ● Remove (3) T-25 Torx screws from the front edge of the soundbar cover and then unclip and remove set aside Step 15 ● Remove the fir tree clip, then gently unclip the T-panel, (you will NOT be removing from the vehicle just gaining enough space...
- Page 7 Disassembly Step 16 ● Unclip rear door sill panel first two clips by moving towards the center of the vehicle Step 17 ● Unclip the two covers on B-Pillar sill panel Step 18 ● Unclip and remove B-Pillar sill panel Page 7 of 23...
- Page 8 Subwoofer Install if applicable Step 19 ● If no subwoofer being install skip Steps 19 to 22 Remove (4) 10mm bolts securing the under seat storage compartment, (may need to remove rubber insert to gain access to bolts) Step 20 ●...
- Page 9 Subwoofer Install if applicable Step 21 ● Cut a small hole in the carpet (as pictured) to pass the subwoofer extension harness through going toward the outside of the vehicle along door seal toward passenger seat area Step 22 ● Install jack Page 9 of 23...
-
Page 10: Wiring Install
Wiring Install Step 23 ● Disconnect OEM connector from soundbar, and connect new harness, and then zip tie along OEM wiring moving down the B-Pillar to under the passenger seat Step 24 ● Clip the T-panel into place and install the first tree clip Page 10 of 23... - Page 11 Wiring Install Step 25 ● Clip soundbar cover into place and install (3) T-25 Torx screws on the front edge Step 26 ● Clip dome light back in place Step 27 ● Place passenger roll cage cover into position and install (4) T25 Torx screws Page 11 of 23...
- Page 12 Wiring Install Step 28 ● Clip the B-Pillar panel back into place sliding under rear door seal panel Step 29 ● Clip (2) covers back on the B-Pillar seal panel Step 30 ● Clip rear door seal panel into the B-Pillar panel Page 12 of 23...
- Page 13 Wiring Install & Assembly Step 31 ● Install front (2) roof sections and refer to your Jeep owner manual for installation of top Step 32 ● Pull back carpet along center console. Then run the RCAs and remote turn on from under the seat to the glove box area along the center console, then route the wire...
- Page 14 Wiring Install & Assembly Step 34 ● Connect the remote wire to the PAC Audio pigtail harness, then connect the interface box to the pigtail harness, (at this point the RCAs can be plugged in and reference the labels to connect properly) Step 35 ●...
- Page 15 Wiring & Amplifier Install Step 37 ● Remove grommet Step 38 ● Using a utility knife, make a small cut Step 39 ● Pass the power wire through the grommet and to the underside of the vehicle, and then install the grommet back into its location Page 15 of 23...
- Page 16 Wiring & Amplifier Install Step 40 ● Install the grommet back into its location Step 41 ● Under the vehicle zip tie the harness along the OEM wire channel should move forward into the fender area Step 42 ● Pass power wire up passenger fender near battery Note Pass a fish tape from top down...
- Page 17 Wiring & Amplifier Install Step 43 ● Crimp and heat the fuse butt connector by the battery Step 44 ● Remove 70A MAXI fuse and make connection to the battery with a 10mm socket Step 45 ● Place front speaker wire harness under passenger seat and route wires along OEM harness from under seat to door jam routing...
- Page 18 Wiring & Amplifier Install Step 46 ● Attach Black ground wire, to the factory ground stud under the Passenger seat Step 47 ● Place amplifiers on mounting plate in order pictured ● Loosely start M4 screws mounting amplifiers, once all screws have been installed go back SUBS...
- Page 19 Wiring Install & Assembly Step 49 ● Lower the seat and install the (4) T-50 Torx bolts and align the rear amp plate mounts to the rear bolts, then install the RCAs into the appropriate amplifer Step 50 ● Zip tie front speaker wires along OEM wires to pass up into the dash toward the passenger front speaker location...
- Page 20 Wiring Install & Assembly Step 52 ● Connect passenger door harness, door strap and install 10mm nut Step 53 ● Clip passenger kick panel cover Step 54 ● Pass the driver side speaker wire along the glove box lower frame, behind glove box door gear, and into the center dash area Page 20 of 23...
- Page 21 Wiring Install & Assembly Step 55 ● Continue routing the driver side speaker wire under the lower center dash wire to driver side Step 56 ● Continue passing driver speaker wire from center dash area to under steering column area and route wire along lower dash support behind bracing NOTE...
- Page 22 Wiring Install & Assembly Step 58 ● Install the 70A MAXI fuse at the battery Page 22 of 23...
-
Page 23: Fcc Notification
FCC Notification This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a mobile installation. This equipment generates uses and can radiate radio frequency energy.