1. Manuals
  2. Brands
  3. DoAll Manuals
  4. Sports & Outdoors
  5. FLYWAY 180X
  6. Instructions manual

DoAll FLYWAY 180X Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
FLYWAY
180X

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FLYWAY 180X and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for DoAll FLYWAY 180X

Summary of Contents for DoAll FLYWAY 180X

  • Page 1 FLYWAY 180X...

  • Page 2: Included Parts

    INCLUDED PARTS Cart Handle Assembly With (2) Long & (1) Medium 14mm Hex Bolts with (6) Washers and (3) Nuts Clay Stack Turret Assembly with (12) male/female stacker poles, (12) female/female stacker poles, and (24) bolts (these come fastened to the poles). (4) Short 14mm Hex Bolts, (8) washers and (4) nuts to connect Wobbler to Wobbler Base Main Spring and Spadebolt...
  • Page 3 NOTES...
  • Page 4 Medium Long STEP 1 Prior to assembly, please be sure that all zip ties, cardboard, styrofoam, and bubble wrap are removed from the unit. Using a 14MM socket for the bolts and a 13MM for the nuts, assemble the cart handle using the 2 long and 1 medium length bolts.

  • Page 5: Bottom View

    Long Bottom View Long Short STEP 2 3 (from Step 1) Using a 14MM socket for the bolts and 13MM for the nuts, attach the Wobbler base to the Axle and Cart Handle using the 2 long and 2 short length 14mm bolts.
  • Page 6 STEP 3 Slide a Washer, then a Wheel, then another Washer onto one side of the axle, Secure with a “C” clip. Repeat this for the second side.
  • Page 7 STEP 5 Using a 14MM Socket for the Bolts and a 13MM for the Nuts, secure the Wobbler to the Wobbler base using the (4) provided bolts, 1 Bolt, 2 Washers, 1 Nut on each corner. (In order: Bolt, Washer, Wobbler, Wobbler Base, Washer, secure with Nut)
  • Page 8 Front side Rear side STEP 6 This side towards rear of trap Using a 14MM Socket for the Bolts and a 13MM for the Nuts, secure the Trap Base to the top of the Wobbler using the (4) provided bolts, 1 Bolt, 2 Washers, 1 Nut on each corner.
  • Page 9 Trap Head Rear Front Trap Base STEP 7 Bolts and Plastic Washers (Circled in white, stacker poles and safety ring not yet installed) Using a 17MM Socket for the Bolts and a 13MM for the Nuts, secure the Trap Head (9) to the Trap Base (8) using the (4) provided bolts and (4) plastic Washers.
  • Page 10 Figure 1 Figure 2 STEP 8 Hook the Safety Ring onto the Safety Ring Arms (top of Figure 1), then secure to the rear of the Trap Head by loosening the two bolts (bottom of Figure 1) slightly, then push the ends of the ring under the clamps and resecure the 2 bolts.
  • Page 11 Rear of Trap Head Underneath Trap Head Figure 1 Figure 2 STEP 9 Hook the Main Spring under the Trap Head Pivot. (Figure 1) Push the Spade Bolt through the hole in the rear of the Trap, then secure with the provided tension knob until you feel tension on the spring.

  • Page 12: Warranty And Customer Service

    THANK YOU ONCE THE MAIN SPRING IS INSTALLED, THE TRAP IS NOW LIVE AND CAN GO OFF IF LEFT IN THE COCKED POSITION. PLEASE USE EXTREME CAUTION AND ALWAYS REMOVE SPRING WHEN TRANSPORTING, ADJUSTING, OR STORING THE TRAP. Warranty & Customer Service Register your product online at www.doalloutdoors.com.

  • Page 13: Operation

    Operation 1. Make sure deep cycle battery (not included) is fully charged. Before clamping wobbler and trap alligator clips to battery, make sure the toggle switch on the trap is set to off. **NEVER CARRY TRAP BY THROWING ARM - THIS CAN BEND AND AFFECT PERFORMANCE! 2.
  • Page 14 NOTES...

  • Page 15: Troubleshooting

    Troubleshooting ***ALWAYS REMOVE MAIN SPRING PRIOR TO TROUBLESHOOTING*** MACHINE NOT TURNING ON 1. CHECK BATTERY CONNECTION. THE MACHINE DRAWS 16 AMPS TO WORK PROPERLY. WE RECOMMEND A DEEP CYCLE BATTERY WITH A MINIMUM OF 675 COLD CRANKING AMPS. 2. CHECK THE 15A AUTOMOTIVE BLADE FUSE IN THE REAR OF THE TRAP HEAD. REMOVE THE COVER AND PULL THE FUSE OUT TO INSPECT.

Table of Contents