Page 2
Thank you for choosing this product. This User Manual contains important safety information and instructions on the operation and maintenance of your appliance. Please take the time to read this User Manual before using your appliance and keep this book for future reference. Icon Type Meaning...
1. SAFETY INSTRUCTIONS Operating voltage / frequency (220-240) V~/50Hz Total current (A) Water pressure (Mpa) Maximum 1 Mpa / Minimum 0. 1Mpa Total power (W) 2200 Maximum washing capacity (dry laundry) (kg) • Do not install your machine on a carpet or such grounds that would prevent the ventilation of its base.
NOTE: For a softcopy of this user manual, please contact the following address: “info@svanelectro.com”. In your e-mail, please provide the model name and serial number (20 digits) which you can find on the appliance door. Read this user manual carefully. Your machine is for domestic use only.
Page 6
exposed to air for a long period of time. Only put softener or detergent in the drawer at the beginning of each wash. • Unplug your Washing Machine and switch off the water supply if the Washing Machine is left unused for a long time. We also recommend that you leave the door open to prevent build up of humidity inside the Washing Machine. • Some water may be left in your Washing Machine as a result of quality checks during production. This will not affect the operation of your Washing Machine. • The packaging of the machine could be hazardous to children. Do not allow children to play with the packaging or small parts from the Washing Machine. • Keep the packaging materials in a place where children cannot reach them, or dispose of them appropriately. • Use pre-wash programs only for very dirty laundry. Never open the detergent drawer while the machine is running. • In the event of a breakdown, unplug the machine from the mains supply and turn the water supply off. Do not attempt to carry out any repairs. Always contact an authorised service agent. • Do not exceed the maximum load for the washing programme you have chosen. Never force the door open when your Washing Machine is running.
Page 7
your machine. • Please follow the manufacturers’ instructions regarding the use of fabric conditioner or any similar products that you intend to use in your Washing Machine. • Make sure that the door of your Washing Machine is not restricted and can be opened fully. Install your machine in a location that can be fully ventilated and preferably has constant air circulation.
Page 8
it must be replaced, this should only be done by qualified personnel. Risk of flooding • Check the speed of water flow before placing the drain hose in a sink. • Take necessary measures to prevent the hose from slipping. • Water flow may dislodge the hose if it is not properly secured. Make sure the plug in your sink does not block the plug hole. Danger of Fire • Do not store inflammable liquids near your machine. • The sulphur content of paint removers may cause corrosion. Never use paint removing materials in your machine. • Never use products that contain solvents in your machine. • Please ensure that garments loaded into your Washing Machine are free from foreign objects such as nails, needles, lighters and coins.
The machine must be carried by at least 2 people. Child safety • Do not leave children unattended near the machine. Children might lock themselves in the machine resulting in risk of death. • Do not allow children to touch the glass door during operation. The surface becomes extremely hot and may cause damage to skin. • Keep packaging material away from children. • Poisoning and irritation may occur if detergent and cleaning materials are consumed or come into contact with the skin and eyes. Keep cleaning materials out of the reach of children. 1.2 During Use • Keep pets away from your machine. • Please check the packaging of your machine before installation and the outer surface of the machine once the packaging has been removed. Do not operate the machine if it appears damaged or if the packaging has been opened. • Your machine must only be installed by an authorised service agent. Installation by anyone other than an authorised agent may cause your warranty to be void.
hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision. • Only use your machine for laundry that is labelled as suitable for washing by the manufacturer. • Before operating the washing machine, remove the 4 transit bolts and rubber spacers from the rear of the machine. If the bolts are not removed they may cause heavy vibration, noise and malfunction of the machine and cause the guarantee to be void.
Page 11
• Do not exceed the maximum load for the washing programme you have chosen. This will allow your machine to run in energy saving mode. • Do not use the pre-wash feature for lightly soiled laundry. This will help you save on the amount of electricity and water consumed. CE Declaration of conformity We declare that our products meet the applicable European Directives, Decisions and Regulations and the requirements listed in the standards referenced. Disposal of your old machine The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. EN - 8...
2. TECHNICAL SPECIFICATIONS 2.2 Technical Specifications Operating voltage / (220-240) frequency V~/50Hz (V/Hz) Total current Maximum: 1 Water pressure Minimum : 0.1 (Mpa) Total power 2200 Maximum dry laundry capacity (kg) Spinning revolution 1200 (rev / min) Programme number 2.1 General Appearance Dimensions 1. Electronic Display (mm) 2.
3. INSTALLATION 3.2 Adjusting the Feet / Adjusting Adjustable Stays 3.1 Removing the Transit Bolts 1. Do not install your machine on a surface (such as carpet) that would prevent ventilation at the base. • To ensure silent and vibration-free operation of your machine, install it on a firm surface. • You can level your machine using the adjustable feet. • Loosen the plastic locking nut. 1. Before operating the washing machine, remove the 4 transit bolts and rubber spacers from the rear of the machine. If the bolts are not removed, they may cause heavy vibration, noise and malfunction of the machine and void the warranty.
• The mains cord of your washing should be connected to cold water inlet machine is equipped with an earthed and red capped hose to the hot water plug. This plug should always be inlet (if applicable). inserted to an earthed socket of 10 • To prevent water leaks at the joints, amps. either 1 or 2 nuts (depending on your machine’s specifications) are supplied • If you do not have a suitable socket and in the packaging with the hose. Fit these fuse conforming with this, please ensure nuts to the end(s) of the water inlet hose the work is carried out by a qualified that connect to the water supply. electrician. 2. Connect new water inlet hoses to a ¾ ˝, • We do not take responsibility for threaded tap. damage that occurs due to the use of ungrounded equipment.
3.5 Water Discharge Connection 4.1 Detergent Drawer • Connect the water drain hose to a standpipe or to the outlet elbow of a household sink, using additional equipment. • Never attempt to extend the water drain hose. • Do not put the water drain hose from your machine into a container, bucket or bathtub. • Make sure that the water drain hose is not bent, buckled, crushed or extended. • The water drain hose must be installed at a maximum height of 100 cm from the ground. 4. CONTROL PANEL OVERVIEW 1. Detergent Drawer 2. Programme Dial 3.
4.2 Sections 4.3 Program Dial Main wash detergent compartment: This compartment is for liquid or powder • To select the desired programme, turn detergents or limescale remover. The fluid the programme dial either clockwise or detergent level plate will be supplied inside anti-clockwise until the marker on the your machine. (*) programme dial points to the chosen Fabric conditioner, starch, detergent programme. compartment: • Make sure that the programme dial is set exactly to the programme you want. 4.4 Electronic Display This compartment is for softeners, conditioners or starch. Follow the instructions on the packaging. If softeners leave residue after use, try diluting them or using a liquid softener.
5. USING YOUR curtains or place them in a washing net or bag. WASHING MACHINE 6. Reverse textiles such as pants, knitwear, t-shirts and sweat shirts. 5.1 Preparing Your Laundry 7. Wash socks, handkerchiefs and other small items in a washing net. Can be Normal Do not bleach bleached washing Maximum Maximum ironing ironing Do not iron temperature temperature 150°C 200°C Can be dry Dry flat No dry cleaned cleaning...
weights of typical laundry items: of the detergent drawer. Do not exceed the MAX level. LAUNDRY TYPE WEIGHT (gr) • Thick softeners may cause clogging of Towel the drawer and should be diluted. Linen • It is possible to use fluid detergents in Bathrobe 1200 all programmes without a pre-wash. To do this, slide the fluid detergent level Quilt cover plate (*) into the guides in compartment Pillow slip II of the detergent drawer. Use the lines on the plate as a guide to fill the drawer Underwear to the required level. Tablecloth (*) Specifications may vary depending on the machine purchased. • Load each item of laundry separately. 5.4 Operating Your Machine • Check that no items of laundry are trapped between the rubber seal and the door.
5.7 Auxiliary Functions to start the washing cycle. • If you have skipped the delay time you would like to set, you can keep pressing the delay key until you reach that time again. • To use the time delay function, you need to press the Start/Pause key to start the machine. Before starting the program, Note: After selecting the delay function, you can select other functions without you can select auxiliary functions if you touching the “Start/Pause” key, and then wish so. you can touch the “Start/Pause” key to • Press the key of the auxiliary function you enable time delay. want to select. To cancel the delay function: • If the symbol of the auxiliary function is • If you did not press the Start/Pause key, continuously on in the electronic display, the...
Page 20
3. Stain selection selection to remove the stain. 4. Selecting the washing water temperature You can make use of these auxiliary functions on washing depending on the types of stains. You can use the washing water temperature setting key to set the temperature of the Warning: Do not let the stains on your washing water for your laundry. laundries to get dry and stuck in order for the auxiliary function dedicated for • When you select a new program, soiling level selection to fully perform its the selected program’s maximum functions.
5.8 Auxiliary functions 2. Extra rinse auxiliary function You can use auxiliary functions to make the best washing selection for your laundry. To You can use this auxiliary function for extra do this, you can touch the options key on rinsing on your laundry. To enable the extra the display panel to enable the following: rinse function, keep pressing the options Prewash auxiliary function key until the extra rinse symbol turns Extra rinse auxiliary function on. If the extra rinse LED is constantly on Easy ironing auxiliary function in the electronic display, it means that the Anti-allergy auxiliary function. auxiliary function is selected. Note: When you want to select the 1. Prewash auxiliary function extra rinse auxiliary function, if does not appear on the display, this means that this feature is not available in the selected washing program. 3.
4. Anti-allergy auxiliary function washing program. (It is recommended to load the machine with half or less than half of the capacity of the selected washing program.) To enable this function, you can touch the Eco/Quick Wash selection key on the display panel to turn on the LED light of the symbol NOTE: If you load the machine with half or less than half of the laundry capacity of the selected washing program, the You can use this auxiliary function to add machine will detect it thanks to the half load another rinse cycle for your laundry. Your detection system, and this way, it will wash machine will use hot water in all rinsing your laundry with less energy and less water in a shorter time. When your machine steps. (It is recommended for sensitive skin detects half load, LED light of the symbol clothing, baby clothes and underclothes). To enable the anti-allergy auxiliary function, will automatically turn on in the display panel. keep pressing the options key until the anti- (*) The appliance specifications may vary allergy function symbol turns on. If the depending on the purchased product. anti-allergy LED is constantly on in the • Energy/Water Efficiency Bar: electronic display, it means that the auxiliary function is selected.
To activate child lock, press and hold program will be cancelled. To drain button 2 and 3 simultaneously for at the water in the machine, turn least 3 seconds. ‘’CL’’ will flash on the the program knob to any program electronic display for 2 seconds when the position. Your machine will drain the child lock is activated. water and cancel the program.
Page 25
NOTE: PROGRAMME DURATION MAY CHANGE ACCORDING TO THE AMOUNT OF LAUNDRY, TAP WATER, AMBIENT TEMPERATURE AND SELECTED ADDITIONAL FUNCTIONS. (*) Washing water temperature of the programme is the factory default. (**) 60 C° - 40 C° are energy label declaration programmes. (***) If your machine has the rapid wash auxiliary function, you can enable the quick wash option on the display panel and load the machine with 2 kg or less laundry to wash it in 30 minutes.
7. CLEANING AND 7.2 Water Inlet Filters Water inlet filters prevent dirt and foreign MAINTENANCE materials from entering your machine. We recommend that these filters are cleaned when your machine is unable to receive 7.1 Warning sufficient water, although your water supply is on and the tap is open. We recommend that you clean your water inlet filters every 2 months. Turn your mains power supply off and remove the plug from the socket • Unscrew the water inlet hose(s) from the Washing Machine. before carrying out • To remove the water inlet filter from the maintenance and cleaning water inlet valve, use a pair of long- nosed pliers to gently pull on the plastic of your machine. bar in the filter. Turn off the water • A second water inlet filter is located in the tap end of the water inlet hose. To...
7.3 Pump Filter 6. Close the filter cover. WARNING: The water in the pump may be hot, wait until it has cooled down before carrying out any cleaning or maintenance. (*) Specifications may vary depending on the machine purchased. 7.4 Detergent Drawer The use of detergent may cause residual build up in the detergent drawer over time. We recommend that you remove the drawer every 2 months to clean the accumulated residue. To remove the detergent drawer: • Pull the drawer forwards until it is fully extended. The pump filter system in your Washing Machine prolongs the life of the pump by preventing lint from entering your machine.
8. Body / Drum 1. Body Use a mild, non-abrasive cleaning agent, or soap and water, to clean the external • casing. Wipe dry with a soft cloth. • Rinse with a brush and lots of water. 2. Drum • Collect the residues inside the detergent Do not leave metallic objects such as drawer slot so that they don’t fall inside needles, paper clips, coins etc. in your your machine.
9. TROUBLESHOOTING Repair of your machine should be carried out by an authorised service company. If your machine requires repair or if you cannot solve an issue with the information provided below, then you should: • Unplug your machine from the mains power supply. • Turn off the water supply. FAULT POSSIBLE CAUSE TROUBLESHOOTING Machine not plugged in. Plug machine in. Fuses are faulty. Replace the fuses. No mains power supply. Check mains power. Your machine does not start. Start/Pause button not pressed. Press the Start/Pause button. Programme dial ‘stop’ position. Turn the programme dial to the desired position. The machine door is not Close the machine door. completely closed.
FAULT POSSIBLE CAUSE TROUBLESHOOTING Your washing is too dirty for the Use the information in the programme tables to programme selected. select the most appropriate programme. Unsatisfactory washing Amount of detergent used Use the amount of detergent as instructed on the result. insufficient. packaging. There is too much laundry in your Check that the maximum capacity for the machine. selected programme has not been exceeded. Increase the amount of detergent following the Hard water. manufacturer’s instructions. Unsatisfactory washing result. Your laundry is too tightly packed Check that your laundry is spread out. together in the drum. As soon as the machine is The end of water drain hose is too Check that the drain hose is at a suitable height. loaded with water, water low for the machine.
11. DESCRIBING THE ENERGY Use programmes of shorter duration for lightly soiled laundry and daily washes. LABEL AND SAVING ENERGY Carry out cleaning and maintenance at regular intervals. 1. Brand 2. Model 3. Energy Class 4. Energy Consumption 5. Noise Value While Washing 6. Noise Value While Spinning 7. Annual Water Consumption 8. Dry Laundry Capacity 9. Spinning Performance Energy use and water consumption may vary based on water pressure, water hardness, water temperature, ambient temperature, amount of laundry, additional function selection and voltage fluctuations.
Need help?
Do you have a question about the ALF1129 and is the answer not in the manual?
Questions and answers