JVC HR-S5000U Service Manual page 23

INSERT EDITING
Insert editing means recording a new scene into a section of pre-recorded tape so that a part of the original recording can be re­
placed with a new sequence without excessive picture distortion at edit-in and edit-out points. Thanks to the flying erase head,
clean edits can be obtained. New video and audio signals to be inserted can come either from another video cassette recorder or
the built-in tuner.
CAUTION
Since video and audio signals are recorded simultaneous­
ly, both are replaced with new recordings simultaneo
However the normal audio soundtrack remains un­
Connection
For inserting video and audio signals from another video cassette recorder.
S-VHS Y/C connection.
14.l
(See page
Procedure •
switch on the TV receiver.
II
•Set the TV receiver in the appropriate mode.
ll
Load a pre-recorded cassette.
Press TV/VIDEO to engage the VIDEO mode (the indi­
II
cator ligh15), if necessary. (See page 10.)
Press the SIMU LCAST, AUX on the remote control )
("O"
II
and S-VHS buttons a s required. (See chart above.)
Ill
Set the Hi-Fi audio recording level. (See page 1 7.)
Play back the tape to determine the edit-out point (the
II
end of the tape section to be replaced) .
Ill
Press the PAUSE/ST I L L button at the edit-out point.
Press the COUNTER RESET button.
II
•The counter will be reset to
"OH OOM OOs".
Press the REW button to determine the edit-in point (the
ml
beginning of the tape section to be replaced) .
II
Press the PAUSE/ST I L L button at the edit-in point.
Press the INSERT button.
•This engages the I nsert Standby mode in which the input
signal can "be monitored on the TV screen; the still picture
changes into the input signal that you are going to re­
cord.
II
•The input sound signal can also be monitored.
Operate the source equipment properly.
•Play back on another recorder the tape program to be
inserted.
•Select the channel to be recorded.
m
•Select the channel and set the FM tuner.
Press the PLAY /X2 button to start insert editing.
•Now video and audio signals will be recorded simultane­
ou�y.
Setting options of the relevant buttons
�
SIMU LCAST and AUX buttons
I
Source
sly. a
AUX (with S-VHS set as required
J � i ; � e n ': : :rams from
- see page 8)
i
1
TUNER
To insert TV programs
the built-in tuner (SIMULCAST button pressed to
OFF)
SIMULCAST
To insert FM simulcast
'
(button pressed to ON)
programs
•At the counter reading of
"OH OOM OOs",
stop automatically.
•The tape will continue running in the Play mode.
O
Notes:
*' '
• Do not use the ST P button to stop insert editing. If you
press the STOP button, the tape stops and the Insert Edit
mode is cancelled.
• I f you wish to stop i rt editing before the specified edit-
out point is reached, ess the COUNTER RESET button.
Then the Play mode will be entered.
• Insert editing is also possible without determining the edit·
out point. Simply start insert editing at the edit-in point
and, where you wish to stop insert editing, press the
PAUSE/ST I LL button. Since this recorder incorporates a
flying erase head, even this simplified procedure makes
clean edits, though there may be a slight discrepancy
between the actual and intended edit points.
• The recording mode (SP or EP) is automatically determined
by the previous recording on which the new segment is
inserted regardless of the setting of the SP/EP button.
• I f the edit start point of the new scene lies in the SP mode
and the edit end point of the same scene lies in the EP
.
mode or vice versa, the inserted picture will distort at the
switching point in the recording mode.
• If there is a non-recorded section on the tape, the I nsert
Edit mode will be cancelled automatically and the Pla y
mode will be engaged.
• Insert editing is not possible with non-recorded cassettes or
cassettes whose safety tab has been removed.
- 33 -
VideoMovie recordings can be edited by using a VideoMovie camcorder (with playback facility) or a 2nd video deck.
Through use of a cassette adapter, VideoMovie recordings can be treated just like regular VHS cassettes.
H R-SSOOOU
_ ....
JVI:
recording will
Playback deck
• Connect the playback deck's VIDEO OUT and AUDIO
OUT connectors (o( the VideoMovie's AV OUT) to the
recording deck's V I DEO IN and AUDIO IN connectors.
• Set the recording deck's SOURCE setting to AUX.
• Press the recording deck's S-VHS button as required.
• Put the playback deck in the Play mode.
• Put the recording deck in the Record mode.
Notes:
• For S-VHS editing, also refer to page 14.
• For monaural audio connection, use the AUDIO IN L con­
nector.
TAPE-TO-TAPE EDITING
VHS-C cassette
Cassette adapter
.. --- ---
- - -- - - -
.... EJ
. - · -
.... ...
HR-SSOOOU
_ ....
JVI:
Recording deck
Tips for obtaining better results
The quality of the edited tape may vary depending on the
position of the E D I T switch . It is recommended that you
first make some trial recordings.
EDIT
• With the EDIT switch of the playback deck
set to ON and recording deck to O F F,
OFF [DJ ON
• With the EDIT switch of both playback and
recording decks set to ON, and
• With the EDIT switch of both decks set to
O F F .
Choose the setting combination that best suits your
preference.
Note: Also refer to the instruction manual of the 2nd
34
video recorder you are using.
- -
- EJ
R ecor 1ng d" deck
TV receiver
- --- - - -
--- ---
. .
.. .. ...