Table of Contents
Advertisement
Quick Links
STRIP FRESHENER™
YETTER COMPRESSOR
YETTER MANUFACTURING CO.
FOUNDED 1930
Colchester, IL 62326-0358
Toll free: 800/447-5777
309/776-3222 (Fax)
Website:
www.yetterco.com
E-mail:
info@yetterco.com
GERMINATE UNIFORMITY ™
2984-050D/051A
CAB CONTROL™
OPERATOR MANUAL
PARTS IDENTIFICATION
2565-968_REV_D ● 02/2024
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Yetter CAB CONTROL STRIP FRESHENER 2984-050D
- Page 1 2984-050D/051A CAB CONTROL™ STRIP FRESHENER™ YETTER COMPRESSOR OPERATOR MANUAL PARTS IDENTIFICATION 2565-968_REV_D ● 02/2024 YETTER MANUFACTURING CO. FOUNDED 1930 Colchester, IL 62326-0358 Toll free: 800/447-5777 309/776-3222 (Fax) Website: www.yetterco.com E-mail: info@yetterco.com GERMINATE UNIFORMITY ™...
-
Page 2: Foreword/Warranty
WARRANTY Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This warranty being expressly limited to replacement at the factory of such parts or products as shall appear to be defective after inspection. -
Page 3: Safety Precautions
SAFETY PRECAUTIONS A brief description of signal words that may be used in this manual: CAUTION: Used as a general reminder of good safety practices or to direct attention to unsafe practices. WARNING: Denotes a specific potential hazard. DANGER: Denotes the most serious specific potential hazard. CAUTION Consult your implement and tractor operator’s manual for correct and safe operating practices. -
Page 4: Table Of Contents
TABLE OF CONTENTS FOREWORD/WARRANTY.………………………………………………..…...2 SAFETY PRECAUTIONS..…………………………….…………………….3 2984 STRIP FRESHENER CC ADVANTAGES & DIMENSIONS....4 FEATURES / BOLT TORQUE…..………………………………………….5 ASSEMBLY INSTRUCTIONS...............6 – 15 OPERATION PRECAUTIONS……………………………...…..……..16 – 17 OPERATION ..................17 – 18 MAINTENANCE………………………………………………………...…19 – 20 PARTS IDENTIFICATION 2984-050/051 STRIP FRESHENER CC ASSEMBLY………………... 21 – 22 2984-132 PARALLEL LINKAGE ASSEMBLY………………………………. -
Page 5: Features / Bolt Torque
CHECK HARDWARE DAILY FOR DAMAGE, WEAR, & LOOSENESS. TIGHTEN AS NEEDED TOOLS NEEDED: ½” Drive Impact, ½” Drive Torque Wrench, ¼” Drive Socket & Ratchet Set, Funnel for adding oil in Yetter Hyd. Compressor, Air Tubing Cutters, Side Cutters, Pliers, Standard Wrenches, Standard Sockets, Tape Measure, Marker... -
Page 6: Assembly Instructions
& use the hardware to mount each unit. If clearance issues with weldments or hinge points on the toolbar arise, alternate parts may be required. Fold the toolbar when all units installed to check for any clearance issues. NOTE: OFFSET MOUNTING BRACKET OPTIONS ARE AVAILABLE, CALL YETTER SERVICE, 1-800-447-5777... - Page 7 Assembly Instructions Row Cleaner Assembly Assemble wide/narrow pivot arms, depending on application, to mount on strip freshener CC unit. Narrow arms go on inside of row cleaner mount plates & wide arms go on outside of row cleaner mount plate. Place a pivot bushing in rear hole on each side of pivot arms, align hole on each arm with rear hole on each side of row cleaner mount bracket, slide a 5/8”...
- Page 8 YOU SHOULD EXERCISE YOUR OWN BEST JUDGEMENT TO FIT YOUR SITUATION. Use mounts supplied or depending on application different mounts may need to be built or Yetter mounts may need modified. Be sure to check clearance in all locations, especially noting tractor tires, folding/unfolding toolbar for transport mode, marker arms, &...
- Page 9 3/8” hydraulic hose for the compressor pressure using -6JIC – -8ORB adaptor. Connect the hydraulic hose attached to case drain on the motor to the case drain connector on the tractor. Case drain coupler not provided. The Yetter hyd.
- Page 10 YOU SHOULD EXERCISE YOUR OWN BEST JUDGEMENT TO FIT YOUR SITUATION. Use mounts supplied or depending on application different mounts may need to be built or Yetter mounts may need modified. Be sure to check clearance in all locations, especially noting tractor tires, folding/unfolding toolbar for transport mode, marker arms, &...
- Page 11 Assembly Instructions Mount the Control Box Attach the 2984-512 Ram ball base to the tractor’s monitor mounting device. Some tractors have round tube & some have slotted flat steel. Pick a location near the right rear corner post so that adjustments can be made easily while viewing the strip freshener units’ performance. Attach the 2984-513 double socket arm to the tractor mounted ball &...
- Page 12 Install the connector not provided for your tractor at the bare end of the 2940-153 and connect to tractors switched power source. Connect the black wire on the Yetter harness to the black wire of the switched power harness. Connect the red wire on the Yetter harness to the orange wire on the switched power harness.
- Page 13 Assembly Instructions Plumbing Each Strip Freshener – Row Unit Bundle Row Cleaner Down – Use ¼” BLACK plumb this circuit Row Cleaner Up – Use ¼” BLUE airline to plumb this circuit Row Unit Down Force – Use ¼” ORANGE Rolling Basket Down –...
- Page 14 Assembly Instructions Plumbing Strip Freshener Trunk Airlines General Plumbing Instructions Smaller, rigid toolbars will have 1 trunk airline from 1 row to last row for each circuit. Folding toolbars will have 3 trunk airline groups for each circuit; left wing, center frame, &...
- Page 15 Assembly Instructions Installation of the Fertilizer Tubes (If Applicable) Below are assembly diagrams for the 4 fertilizer tube kits offered for the 2984 Strip Freshener CC units. An additional clamp on hose is offered for each of the liquid kits to get the fertilizer closer to the soil profile to help keep the fertilizer in the desired location & keep splatter to a minimum. When installing the fertilizer delivery hoses, follow the same route as the airlines.
-
Page 16: Operation Precautions
IMPORTANT: failure to properly set the frame height and levelness can result in less than successful operation of the Yetter product and may result in damaged equipment. All operators should read and thoroughly understand the instructions given prior to using the Yetter product. -
Page 17: Operation
OPERATION The Tank Pressure should always be above 100psi. If using Yetter Electric/Hydraulic Compressor units, each compressor will shut off at 145psi & engage to recover back to 145psi when tank pressure drops to 120psi. Make sure to have all circuits set at 0psi when setting the toolbar & units for optimum performance begins. - Page 18 OPERATION ROW CLEANER DOWN ROW CLEANER UP PRESSURE CONTROL PRESSURE CONTROL PULL KNOB TO UNLOCK PULL KNOB TO UNLOCK TURN CLOCKWISE TO INCREASE TURN CLOCKWISE TO INCREASE ROW CLEANER TURN COUNTERCLOCKWISE TO TURN COUNTERCLOCKWISE TO PRESSURE GAUGE DECREASE AIR PUSH DECREASE AIR KNOB TO LOCK PUSH KNOB TO LOCK...
-
Page 19: Maintenance
Hydraulic compressors are shipped empty of pump lubrication & need oil added before operation. Provided is a 1 Liter bottle of grade 111 synthetic. Add oil until oil level is seen half way up on the sight glass. Recheck oil level on the dipstick. Yetter part # for new bottle is 2940-550. - Page 20 Alternative Lubricants Conditions in certain geographical areas may require special lubricants and lubrication practices which do not appear in the operator’s manual. If there are any questions, consult Yetter Manufacturing Co. to obtain the latest information & recommendation. Part #...
-
Page 21: Parts Identification 2984-050/051 Strip Freshener Cc Assembly
2984-050/051 STRIP FRESHENER CC PART IDENTIFICATION... - Page 22 2984-050 STRIP FRESHENER CC PART IDENTIFICATION...
-
Page 23: 2984-132 Parallel Linkage Assembly
PIVOT HARDWARE PART IDENTIFICATION ITEM PART # DESCRIPTION 2502-352 5/8-11 X 6 HHCS GR 8 ZP 2520-462 5/8-11 HEX LOCK NUT GR 8 ZP 2526-451 5/8 STD FLAT WASHER ZP 2984-158 PARALLEL ARM ASSEMBLY *2984-160 PARALLEL ARM ASSEMBLY 7X7/7X9 2984-330 9/16”... -
Page 24: Row Cleaner Mount / Narrow Row Cleaner Assemlby
2984-241 RM ARM MOUNT PART ID 2984-090A-NR ROW CLEANER ASSEMBLY PART ID ITEM PART # DESCRIPTION 2502-317 ½-13 X 1 ¾ HHCS GR 5 ZP 2502-391 5/8-11 X 2 HHCS GR 5 ZP 2515-305 AIR CYLINDER 2520-357 ½-13 LOCK HEX NUT GR A ZP 2520-459 5/8-11 LOCK HEX NUT GR B ZP 2520-465... -
Page 25: Wide Row Cleaner Assemlby
2984-090A-W ROW CLEANER ASSEMBLY PART IDENTIFICATION ITEM PART # DESCRIPTION 2502-317 ½-13 X 1 ¾ HHCS GR 5 ZP 2502-391 5/8-11 X 2 HHCS GR 5 ZP 2515-305 AIR CYLINDER 2520-357 ½-13 LOCK HEX NUT GR A ZP 2520-459 5/8-11 LOCK HEX NUT GR B ZP 2520-465 5/8-11 SERRATED FLG NUT GR 8 ZP 2526-453... -
Page 26: Gauge Wheel Assembly / Berming Disc Assembly
GAUGE WHEEL ASSEMBLY PARTS IDENTIFICATION ITEM PART # DESCRIPTION 2502-330 5/8-11 X 3 HHCS GR 8 ZP 2502-433 5/8-11 X 4 ½ HHCS GR 8 2520-452 5/8-11 HEX NUT GR 8 ZP 2520-478 5/8-11 SER FLG NUT GR 8 ZP W/ THRDLK 2525-451 5/8 MED LOCK WASHER ZP 2526-454... -
Page 27: Rolling Basket Assembly
ROLLING BASKET ASSEMBLY PART IDENTIFICATION ITEM PART # DESCRIPTION 2515-306 3”BORE X 3” STROKE AIR CYLINDER 2515-307 90 DEG SW ELBOW, ¼”TUBE X 3/8NPTM 2515-856 ¼” AIR FITTING PLUG 2520-460 5/8-18 JAM HEX NUT ZP 2984-265 CYLINDER CLEVIS W.A. ITEM PART # DESCRIPTION 2502-352... -
Page 28: Wheel & Hub/Bearing Assembly
WHEEL ASSEMBLY & HUB/BEARING PART IDENTIFICATION... -
Page 29: Screw Adjust Assembly / 2984-082/083 Fertilzer Tube Kit
SCREW ADJUST ASSEMBLY PART IDENTIFICATION ITEM PART # DESCRIPTION 2510-102 #10-32 X .31 HSHCPS ZP W/ THRDLCK 2526-453 5/8 SAE FLATWASHER ZP 2526-585 DISC SPRING 2530-158 PIN, COILED SPRING, ¼ X 1 ½ HD 2967-652 DETENT PLATE ZP 2967-657 ACME SCREW 2967-699 ADJUSTMENT KNOB 2984-245... -
Page 30: 2984-084 & 2984-085 Fertilizer Kit
FERTILIZER TUBE ASSEMBLY PARTS IDENTIFICATION Item Part # Description 2502-331 5/8-11 X 1 ¾ HHCS GR 5 ZP 2503-256 3/8-16 X ½ SQ HCPSS GR 5 SS 2520-459 5/8-11 LOCK HEX NUT GR 8 ZP 2984-252 CENTER FERT MOUNT W.A. 2984-446 STRIP FRESHENER LIQ TUBE... -
Page 31: Pneumatic Control Box
2984-156 CONTROL BOX PARTS IDENTIFICATION ITEM PART # DESCRIPTION 2565-357 CONTROL BOX DECAL 2984-520 RAM-2461U VESA PLATE ADAPTER 2984-523 ELBOW FITTING, PLF-532-N01U 2984-524 358-910 PUSH PULL VALVE 2984-525 358-910 TOP SELECTOR VALVE 2984-526 CONTROL BOX ENCLOSURE W/ LID 2984-527 HAA51737 GAUGE SHUTTLE 2984-528 PANEL MOUNT GAUGE, 0-100PSI 2984-529... -
Page 32: Compressor/Compressor Mount Kits
RUBBER SPIDER INSERT FOR LOVEJOY COUPLER 2940-554 HYDRAULIC MOTOR HOUSING COVER MOTOR ELBOW FITTING INLET ELBOW FITTING 13 2940-519A HYDRAULIC COMPRESSOR FAN, CAST (will fit on all Yetter Hyd. Compressors) 2940-549 HYDRAULIC COMPRESSOR AIR FILTER (FILTER ELEMENT ONLY) FILTER ELBOW BACK GUARD AIR MANIFOLD 2940-416... - Page 33 2940-101A PARTS IDENTIFICATION Item Part # Description 1 2940-416 175PSI TANK SAFETY RELIEF VALVE 2 2940-439 0-160PSI HYDRAULIC COMPRESSOR GAUGE AIR MANIFOLD 4 2940-635 3/8PC X 3/8NPT 90° ELBOW FITTING, SWIVEL 5 2940-336 HIGH PRESSURE RELIEF VALVE (NO FITTINGS) 1/4”PC TO 1/8NPT ELBOW 1200-323 6 2940-377 COMPRESSOR PRESSURE SWITCH 125-145PSI 7 2940-395...
-
Page 34: Small Parts / Airline Kits
2984-168 SMALL PARTS KIT IDENTIFICATION ITEM PART # DESCRIPTION 1200-323 ¼” TUBE TO 1/8NPT MALE 90° SWIVEL 2515-307 ¼” TUBE X 3/8NPTM 90° SWIVEL 2515-903 5 CIRCUIT ¼” TEE BANK ASSEMBLY 2515-904 ¼” PUSH PLUG 2515-907 6 PORT FLNG MOUNT PUSH CONNECTOR 2515-911 ¼”... -
Page 35: Troubleshooting
Troubleshooting Guide Problem Cause Corrective Action Compressor will not run 1. air system is off 1. Flip switch to ON on cab controller 2. hydraulics disengaged 2. engage compressor hydraulic circuit 3. no power from battery 3. check power connections from battery, check 2940-150 breaker at the battery 4. - Page 36 2565-968_REV_D ● 02/2024...
Need help?
Do you have a question about the CAB CONTROL STRIP FRESHENER 2984-050D and is the answer not in the manual?
Questions and answers