Table of Contents
Advertisement
TAPE COPY
Please refer to page 20 on how to connect the camcorder.
Ce
ae eae a
a aie hae
aa al gaa aa
a aa
a
a
ne
1 _Connect the camcorder to al VCR.
t PPK ALAMEDA MDSHA PDA EEE
say
i
;
2 Load the recorded tape into the camcorder.
|
:
Set the erasure-prevention switch so that the tape
: cannot be recorded on. (See page 7.)
ad
Se
eae
ae
nal a a
a
a a al a
a ae at
a ee
ea
ea a en
da aaa
:
13 Set the camcorder POWER switch to "PLAYER".
__
Eeer
pai mia in a
t a ipn m miaa
t t e s paa ma a iaa am
n t a aa e m n
mr
t ia
se
a mi paa a
a
m pe
a
e ma a a
l a a at n e a
$
LS Turn on the VCR and load the s tape for
for recording.
5 Set the VCR 1 to external input mode, then set it to
;
recording pause mode. -
playback.
'
eat
e ate eee aerate eee
aera aan a
a a a a ee a eta ee anata ata"e te arate atearetarate ate tata ate a etetatatstetatatatatal
i
1 Start recording on the VCR.
ea
a a
ae
n
A
A A
a
a
6 Press the PLAY button on the camcorder, to start
sane
SOENE
EREE:
Senne
PREPS P IEEE
EEEE
AAAA
R
A
R
AA
a
Aa,
APENRE doa AAA
E
hi
mas
A
E
A
al
A
AA
E, ee
8 When finished, stop recording on the VCR, then
press the STOP button on the camcorder.
f
ee
ee
a
EALA
a
t
Notes:
@ When copying a tape, the picture and sound will not
be as good as on the original tape.
@ During editing operations, it is recommended to
connect the camcorder to an AC outlet with the AC
adaptor/charger.
E On-screen display
When the camcorder is connected to a TV receiver, the
indications appearing in the viewfinder can be displayed
on the TV screen by pressing the DATA ON SCREEN
button. Pressing this button again will cancel the
on-screen display. Please refer to page 20 on how to
connect the camcorder.
tas Note: If the on-screen display is activated during tape
copy, it will be recorded on the tape along with the
picture and sound.
@ LANC terminal
The symbol @ identifies the LANC (Local Application
Contro! Bus System) terminal. If you are using an edit
controller or a computer for special editing functions, the
external equipment is connected to the LANC terminal to
precisely control all the tape transport functions of your
camcorder. Please refer to the concerned equipment
instruction manual for detailed operation.
19
VIDEO LIGHT
A video light (sold separately) can be installed on the
accessory shoe.
E Installing the video light
slide the video light foot (A) into the accessory shoe, until
a click is heard and it is firmly locked into place.
To remove the video light, press and hold button (B), then
pull the video light toward the front.
E Using the video light
Set the POWER switch on the camcorder to "CAMERA",
set the stand-by switch to "STANDBY", then press the
power switch (C) on the video light to turn it on and off.
0s Note: The video light cannot be used if the remote
control is connected to the camcorder.
WARNING:
When the video light is used, it will get very hot. Be careful
not to get burnt by touching the front glass or the light
cabinet when the video light is on or just after it has been
turned off.
If the video light bulb is burnt out, have it replaced by the
dealer where it was purchased.
Advertisement
Table of Contents
