Assembly & Set-Up - Cub Cadet 524 SWE Operator's Manual

Assembly & Set-Up
Contents of Carton Contents of Carton Contents of Carton Contents of Carton
• • • • One Snow Thrower One Snow Thrower One Snow Thrower One Snow Thrower
• • • One Snow Thrower Operator's One Snow Thrower Operator's One Snow Thrower Operator's
Manual Manual Manual
Assembly Assembly Assembly Assembly
Handle Handle Handle Handle
1. 1. 1. 1. Place the shift lever in the Forward-6 position Place the shift lever in the Forward-6 position Place the shift lever in the Forward-6 position Place the shift lever in the Forward-6 position
2. 2. 2. 2. Observe the lower rear area of the snow thrower to be sure Observe the lower rear area of the snow thrower to be sure Observe the lower rear area of the snow thrower to be sure Observe the lower rear area of the snow thrower to be sure
both cables are aligned with roller guides before pivoting both cables are aligned with roller guides before pivoting both cables are aligned with roller guides before pivoting both cables are aligned with roller guides before pivoting
the handle upward. See Fig. 3-1. the handle upward. See Fig. 3-1. the handle upward. See Fig. 3-1. the handle upward. See Fig. 3-1.
NOTE: Make certain the upper ends of each cable are NOTE: Make certain the upper ends of each cable are NOTE: Make certain the upper ends of each cable are NOTE: Make certain the upper ends of each cable are
seated properly in its bracket. seated properly in its bracket. seated properly in its bracket. seated properly in its bracket.
3. 3. 3. 3. Secure the handle by tightening the plastic knob located Secure the handle by tightening the plastic knob located Secure the handle by tightening the plastic knob located Secure the handle by tightening the plastic knob located
on both the left and right sides of the handle. Remove on both the left and right sides of the handle. Remove on both the left and right sides of the handle. Remove on both the left and right sides of the handle. Remove
and discard any rubber bands, if present. They are for and discard any rubber bands, if present. They are for and discard any rubber bands, if present. They are for and discard any rubber bands, if present. They are for
packaging purposes only. packaging purposes only. packaging purposes only. packaging purposes only.
Chute Assembly Chute Assembly Chute Assembly Chute Assembly
1. 1. 1. 1. Remove wing nut and hex screw from chute control Remove wing nut and hex screw from chute control Remove wing nut and hex screw from chute control Remove wing nut and hex screw from chute control
assembly and clevis pin and cotter pin from chute support assembly and clevis pin and cotter pin from chute support assembly and clevis pin and cotter pin from chute support assembly and clevis pin and cotter pin from chute support
bracket. Position the chute assembly (forward-facing) over bracket. Position the chute assembly (forward-facing) over bracket. Position the chute assembly (forward-facing) over bracket. Position the chute assembly (forward-facing) over
the chute base. See Fig. 3-2. the chute base. See Fig. 3-2. the chute base. See Fig. 3-2. the chute base. See Fig. 3-2.
2. 2. 2. 2. Place chute assembly onto chute base and secure chute Place chute assembly onto chute base and secure chute Place chute assembly onto chute base and secure chute Place chute assembly onto chute base and secure chute
control assembly to chute support bracket with clevis pin control assembly to chute support bracket with clevis pin control assembly to chute support bracket with clevis pin control assembly to chute support bracket with clevis pin
and cotter pin removed earlier. See See Fig. 3-3. and cotter pin removed earlier. See See Fig. 3-3. and cotter pin removed earlier. See See Fig. 3-3. and cotter pin removed earlier. See See Fig. 3-3.
6
• • • • Two Replacement Auger Shear Pins Two Replacement Auger Shear Pins Two Replacement Auger Shear Pins Two Replacement Auger Shear Pins
• • One Tecumseh Engine Operator's One Tecumseh Engine Operator's
Manual Manual
Figure 3-1 Figure 3-1
• • • • One Snow Thrower Operator's One Tecumseh Engine Manual One Product Registration Card One Product Registration Card
Manual
2 2 2 2
1 1 1 1
Figure 3-2 Figure 3-2
Figure 3-3 Figure 3-3
3
1 1 1 1