Subscribe to Our Youtube Channel
Related Manuals for Cub Cadet 59A40051727
Summary of Contents for Cub Cadet 59A40051727
- Page 1 Operator’s Manual 45” Snowblower Model 59A40051727 Cub Cadet Yanmar LLC P.o. Box 368023 Cleveland, Ohio 44136-0019 769-04374A PRINTED IN U.S.A. (November 13, 2008)
-
Page 2: Table Of Contents
If you have difficulty with this snow blower; have any questions regarding the controls, operation or maintenance of this equipment; or desire additional information not found in this manual, contact your nearest authorized Cub Cadet Yanmar dealer. If you need assistance in locating a dealer in your area, contact the Customer Dealer Referral Line. -
Page 3: Safe Operation Practices
(Replacement labels After connecting hoses, check that all control lever positions are available through your Cub Cadet Yanmar dealer.) Failure to function as Instructed in this Operator’s Manual. Do not operate follow instructions or safety rules can result in serious injury or until control lever and equipment movements are correct. - Page 4 Operational Keep bystanders, pets and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the Do not allow other people in the area when operating, area. attaching, removing, assembling or servicing equipment; Exercise caution while operating tractor with this attachment, particularly small children.
- Page 5 Adjustment of system relief pressure should be done by a Do not loosen hydraulic fittings or hoses while snow qualified, experienced Cub Cadet Yanmar dealer. Incorrect blower is in stored position. adjustment can result in system failures and serious personal Do not climb or lean on equipment stored on stand.
-
Page 6: Safety Labels Found On The Snow Blower
section 2: labels found on snoW bloWer... -
Page 7: To The Dealer
Model 59A40051727 snow blower assembly. Please read and understand what it says. The Model 59A40051727 45” Snow Blower assembly is designed for use ONLY with certain Cub Cadet Yanmar tractor models. It will NOT fit nor operate safely or properly on or with any other tractor. -
Page 8: Contents
section 5: contents The snow blower attachment components are listed below along with their part numbers. Assemblies are made up of more than one part and do not have a part number. Before beginning installation, lay all components out on a flat surface to assure everything is present. figure 1 11. -
Page 9: Unpacking The Snow Blower
section 6: unpacking The front hitch assembly is required to mount the snow blower on the tractor. If the front hitch is installed it has to be removed for proper installation. Unpacking the Snow Blower Remove the front hitch as follows: Move the tractor and snow blower to a firm flat area large enough Disconnect the hitch hydraulic hoses from the hydraulic to accommodate both. - Page 10 Align the locking collar of the drive shaft with the Mid - PTO Remove the clevis pin and click pin from the jack stand, move shaft and slide the drive shaft fully onto the PTO shaft. If the jack into the third hole and replace the clevis pin and click necessary, compress the locking collar of the drive shaft to pin.
- Page 11 Mounting the Chute Raise the front hitch so that the snow blower is off the ground; then stop the tractor engine and engage the parking NOTE: Grease the chute base before attaching. See Figure 9. brake. The chute was shipped with two of the chute clamps attached. To Check to verify that the snow blower pin is fully seated into attach the chute, place it onto the chute base and secure it with the front hole of the ‘A’...
- Page 12 Secure the crank assembly as shown in Figure 11 using two To adjust the skid shoes 5/16-18 x .750 carriage bolts, two .340 x .872 x .060 bell Adjust skid shoes by loosening the six (three on each side) washers and 5/16-18 flange lock nuts. hex nuts, washers, and carriage bolts securing the skid shoes to the auger housing.
-
Page 13: Maintenance
PTO Lubrication Lubricate all pivot points on the drive shaft, stub shaft and blower drive shaft. Roller Chain Hex Nuts figure 16 Lubricate the chain with Cub Cadet Chain Lube. Replace the cover and secure with the previously removed hex nuts. -
Page 14: Service
section 9: service Replacing or adjusting the chain To adjust the tension on the roller chain, proceed as follows: Service Loosen the three hex bolts on each side of the box. See Figure 18. Shave Plate and Skid Shoes The shave plate and skid shoes on the bottom of the snow blower are subject to wear. -
Page 15: Operation
section 10: operation Engaging the Snow Blower Sit on the operator’s seat. Operating the Snow Blower Lock the parking brake. Move foot pedal to the neutral position. The tractor’s implement control lever is used to control the move- Start the engine. ments of the front hitch. -
Page 16: Removing
Chute Crank section 11: reMoving To turn the chute to the right, rotate the chute crank clockwise. To Removing the Snow Blower turn the chute to the left, rotate the chute crank counter-clockwise. If necessary, adjust the skid shoes so that the snow blower Chute Clean-Out Tool will stand upright in its operating position. - Page 17 notes page...
-
Page 18: Parts List
section 12: parts list Snow Blower... - Page 19 Ref. Part Ref. Part Number Description Qty. Number Description Qty. 05244B Bearing Housing 714-0145 Click Pin 603-04598 Housing Assembly 714-04040 Bow-Tie Cotter Pin 714-04059 Hi-Pro Key 603-04600 Chute Assembly 714-0507 Cotter Pin 603-04673 Bracket Assembly 715-0118 Spirol Pin, 5/16-1.75 603-04689 Chain Cover 715-0129 Spirol Pin, .125 x .812...
- Page 20 PTO/Drive System Ref. Part Number Description Qty. 710-0376 Hex Screw, 5/16-18 x 1.00 711-1623 Spline Shaft 712-0429 Hex Lock Nut, 5/16-18 716-0102 Shaft Snap Ring 716-0188 Retainer Ring 717-04642 Drive Shaft 719-3172 Shaft 721-0462 Grease Seal, 1.31 x 1.00 737-3000 Lube Fitting 741-0131 Ball Bearing, 1.00 ID x 2.00 OD...
Need help?
Do you have a question about the 59A40051727 and is the answer not in the manual?
Questions and answers