Sony HCD-SHAKE33 Service Manual page 84

HCD-SHAKE33/SHAKE44/SHAKE55/SHAKE66/SHAKE77/SHAKE88
Ver. 1.1
Pin No. Pin Name
57 to 60 RD4 to RD7
61 DQM0
62 to 69 RD15 to RD8
70 DQM1
71 DVDD33
72 RCLK
73 to 79 RA11, RA9 to RA4
80 RWE#
81 DVSS12
82 CAS#
83 RAS#
84 DVDD33
85, 86 BA0, BA1
87 DVDD12
88 to 92 RA10, RA0 to RA3
93 SPDIF
94 XMAMUTE
95 MFIDET
96 DACVDDC
97 VREF
98 FS
99 DACVSSC
100 CVBS
101 DACVDDB
102 SY/Y/G
103 SC/CB/B
104 CR/R
105 AADVSS
106 ADIN
107, 108 NC
109 AADVDD
ADACVSS2,
110, 111
ADACVSS1
112 ACLK
113 ABCK
114 NC
115 AVCM
116 NC
117 ALRCK
118 ASDATA0
ADACVDD1,
119, 120
ADACVDD2
121 AVDD12_1
122 AGND12
123 RFIP
124 OPDIST
125 IOPMON/OPO
126 SPFG/OP-
127 RF_A
128 RF_B
84
I/O
I/O Two-way data bus with the SD-RAM
O Data mask signal output to the SD-RAM (lower byte)
I/O Two-way data bus with the SD-RAM
O Data mask signal output to the SD-RAM (upper byte)
- Power supply terminal (+3.3V) (digital system)
O Clock signal output to the SD-RAM
O Address signal output to the SD-RAM
O Write enable signal output to the SD-RAM
- Ground terminal (digital system)
O Column address strobe signal output to the SD-RAM
O Row address strobe signal output to the SD-RAM
- Power supply terminal (+3.3V) (digital system)
O Bank address signal output to the SD-RAM
- Power supply terminal (+1.2V) (digital system)
O Address signal output to the SD-RAM
O SPDIF signal output terminal
O Audio muting control signal output terminal
O MFI detection signal input terminal Not used
- Power supply terminal (+3.3V) (for D/A converter)
- Band-gap reference voltage terminal
- Full scale adjustment terminal
- Ground terminal (for D/A converter)
O Composite video signal output terminal
- Power supply terminal (+3.3V) (for D/A converter)
O Component video (Y) signal output terminal
O Component video (Cb/Cb) signal output terminal
O Component video (Cr/Pr) signal output terminal
- Ground terminal (for A/D converter)
I Audio data input from the A/D converter
- Not used
- Power supply terminal (+3.3V) (for A/D converter)
- Ground terminal (for D/A converter)
O Master clock signal output to the audio A/D converter
O Bit clock signal output to the audio A/D converter and sample rate converter
- Not used
- Audio D/A converter reference voltage terminal
- Not used
O L/R sampling clock signal output to the audio A/D converter and sample rate converter
O Audio data output to the sample rate converter
- Power supply terminal (+3.3V) (for D/A converter)
- Power supply terminal (+1.2V) (analog system)
- Ground terminal (analog system)
I AC coupled RF signal input from the optical pick-up block
I Not used
I Positive input to the internal operational amplifi er
I Negative input to the internal operational amplifi er
I RF main beam (C) input from the optical pick-up block
I RF main beam (B) input from the optical pick-up block
Description
Not used
Not used
Not used
Not used
Not used
Not used