SincoSald EVOLUTION SP4-E/N Instruction Manual
  1. Manuals
  2. Brands
  3. SincoSald Manuals
  4. Welding System
  5. EVOLUTION SP4-E/N
  6. Instruction manual

SincoSald EVOLUTION SP4-E/N Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
EVOLUTION SP3-C
EVOLUTION SP4-E/N
EVOLUTION SP5-E/N
FEEDER EVO-4R/N
G.R. EVO/N
MODEL
INSTRUCTION MANUAL
for installation,
use and maintenance
of welding
machines.
Original instructions in Italian.
Please keep for future use.
1.995.241 EN - Rev. 1.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EVOLUTION SP4-E/N and is the answer not in the manual?

Questions and answers

Related Manuals for SincoSald EVOLUTION SP4-E/N

Summary of Contents for SincoSald EVOLUTION SP4-E/N

  • Page 1 MODEL EVOLUTION SP3-C EVOLUTION SP4-E/N EVOLUTION SP5-E/N FEEDER EVO-4R/N G.R. EVO/N INSTRUCTION MANUAL for installation, use and maintenance of welding machines. Original instructions in Italian. Please keep for future use. 1.995.241 EN - Rev. 1.1...

  • Page 2: Table Of Contents

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Contents 1. PREFACE 1.1. PURPOSE OF THE INSTRUCTION MANUAL FOR USE AND MAINTENANCE 1.2. RECIPIENTS 1.3. STORAGE OF THE INSTRUCTION MANUAL 1.4. UPDATING THE INSTRUCTION MANUAL 1.5. HOW TO READ THE INSTRUCTION MANUAL 1.6.
  • Page 3 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6. MACHINE USE 6.1. MACHINE LAYOUT DESCRIPTION 6.1.1. Front and rear layout EVOLUTION version C 6.1.2. Front and rear layout EVOLUTION version E/N 6.2. INSTALLATION & OPERATION FOR MMA WELDING 6.3.
  • Page 4 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.14.3. PASSWORD 6.5.14.4. BLOCKS 6.5.14.5. CONFIG 6.5.15. ADVANCED SETUP Menu 6.5.15.1. ADVANCED CONFIG 6.5.15.2. ADVANCED MODE 6.5.15.3. EQUIPMENT LAYOUT 6.5.15.4. FACTORY RESET 6.5.15.5. INFO 6.5.15.6. NETWORK 6.5.15.7. WELD LOG 6.5.15.8.

  • Page 5: Preface

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 1. PREFACE THE OFFICIAL LANGUAGE CHOSEN BY THE MANU- FACTURER IS ITALIAN. The manufacturer cannot be held liable for translations in other languages that do 1.1. PURPOSE OF THE INSTRUCTION...

  • Page 6: Storage Of The Instruction Manual

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 1.5. HOW TO READ • capable of comprehending and interpreting the operator manual and the safety instructions; THE INSTRUCTION MANUAL • familiar with the emergency procedures and how The Manual is split into chapters, each one dedicated to implement them;...

  • Page 7: General Information

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 2. GENERAL INFORMATION EVOLUTION SP4-E/N plate 2.1. MANUFACTURER IDENTIFICATION DATA NOVAMIX 202 SYN PFC EVOLUTION SP4-E/N MANUFACTURER: SINCOSALD S.r.l EN 60974 - 1 EN 60974 - 1...
  • Page 8 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Pos. 4 Welding machine type symbol: Transform- FEEDER EVO - 4R/N plate er - Rectifier for arc welding Pos. 5 Reference to the legislation followed for welding machine construction: EN 60974-1 Agrate B.za - MB - Italy...

  • Page 9: Declarations Of Conformity

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 2.3. DECLARATIONS OF CONFORMITY 2.6. PREPARATION BY THE CUSTOMER The machine is constructed in compliance with the Unless otherwise agreed in the contract, the follow- relevant EU Directives, applicable at the time of its ing are normally the Customer's responsibility: •...

  • Page 10: Safety

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 3. SAFETY It is, however, essential to diligently follow the follow- ing indications: • It is absolutely forbidden to operate the machine 3.1. GENERAL automatically with the fixed and/or mobile guards SAFETY WARNINGS removed;...
  • Page 11 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N All safety features placed on moving parts to prevent B) Radiation accidents and safeguard safety can not be modified Ultraviolet radiation, emitted from the electric arc, or removed, but must be adequately safeguarded.
  • Page 12 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N - Do not expose cylinders to excessive heat, sparks, F) Burns molten slag or flames. Protect the skin against burns caused by ultraviolet - Do not tamper with the cylinder valves.
  • Page 13 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N be drawn into the welding atmosphere or if radiant Work area control to prevent E.M. interference energy can penetrate into atmospheres containing Before installing the welding machine it is necessary...

  • Page 14: Intended Use

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N which may have been deposited on the transformer They include: or on the diodes of the rectifier unit; to do this use a • inspection of all supporting structures, which jet of dry, clean air.

  • Page 15: Contraindications For Use

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 3.6. SIGNS ATTENTION: It cannot therefore be used as a de- vice tor thaw pipes; any improper use automati- The safety signs must always be clearly visible and it cally voids the warranty and excludes the man- is absolutely forbidden to remove or hide them.

  • Page 16: Residual Risks

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Explosion hazard: Noise: This symbol indicates the presence of Protection goggles or mask explosive substances or explosion hazard. near this symbol. 3.7. RESIDUAL RISKS Careful use of the machine minimises the probability of accidents;...

  • Page 17: Installation

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 4. INSTALLATION the transport document before signing. Do not use the machine, but contact the seller to agree on the procedure to be adopted. 4.1. SHIPPING To this end, it is advisable to carry out a check of...

  • Page 18: Unpacking

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N istics, depending on the weight of the machine itself. If the supply includes only the welding machine, generally weighing less than 25 kg, the packaging consists of a cardboard box without lifting pallets. It can be easily lifted by two operators and taken to the place of use.

  • Page 19: Storage

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Do not lift the machine by the FEEDER or genera- Laws and/or Technical Standards currently in force for tor handles. The machine has a sturdy handle in- safety in workplaces and electrical installations.

  • Page 20: Connections

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N fectly levelled area; levelling can also be carried ATTENTION: It is mandatory to install a circuit out using any adjustment systems present on the breaker with interlocked CEE socket, of adequate capacity and verifying that the earth socket is ef- machine.

  • Page 21: Overview

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 5. OVERVIEW 5.2. FEATURES AND MAIN COMPONENTS 5.1. OPERATING PRINCIPLE MIG/MAG features description EVOLUTION series welding systems have been de- - The new INVERTER is fitted with new generation...

  • Page 22: Environmental Conditions

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 5.6. NOISE up different electrode types to optimise welding performance to the utmost. The equivalent continuous A-weighted sound pres- sure level, emitted by the machine at the workplace in full operating conditions, is less than 70 dB (A).

  • Page 23: Technical Specifications

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 5.7. TECHNICAL SPECIFICATIONS The following table shows the main technical specifications relating to the machine: EVOLUTION EN 60974-1 SP3-C SP4-E/N SP5-E/N 3 Phase Input 400 V - 50/60 Hz...

  • Page 24: Machine Use

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6. MACHINE USE 6.1.2. Front and rear layout EVOLUTION version E/N 6.1. MACHINE LAYOUT DESCRIPTION 6.1.1. Front and rear layout EVOLUTION version C 1. Remote control 2. Water inlet (red) 1.

  • Page 25: Installation & Operation For Mma Welding

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.2. INSTALLATION & OPERATION FOR MMA WELDING Pole +(electrode holder) Pole - (ground cable) 6.3. TIG WELDING WITH “LIFT” Gas connection (pressure reducer) Power switch Gas connection...
  • Page 26 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N In the TIG process welding is achieved by melting the ELECTRODE TYPE two metal pieces to be joined, with the possible addi- Current adjustment field (A) tion of material from the outside, using an arc ignited Ø...

  • Page 27: Remote Current Control

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.3.1. Remote current control POTENTIOMETER The welding machine can accept remote current Adjust current roller control from a potentiometer/ analogue signal or wheel, when it’s roll a digital up/down button signal. Potentiometer...
  • Page 28 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 17-pole connector pin • PARAMETER REGULATION - V • Terminals P(-) / S (+) By regulating the voltage on this input between 1V and 10V the welding parameters (ARC LENGTH, WELDING VOLTAGE, ELECTRONIC INDUCTANCE) are regulated from the minimum to the maximum value.

  • Page 29: Installation & Operation For Mig/Mag Welding

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.4. INSTALLATION & OPERATION FOR MIG/MAG WELDING MIG/MAG Euro torch connection Pole - (ground cable) Extension Signal connector (extension) Pole Power cable Water outlet (blue) Water inlet (red) 1.995.241 EN - Rev.

  • Page 30: Operator Software

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5. OPERATOR SOFTWARE 6.5.1. Introduction This manual describes the functions of the software operating the following control panels: • EVOLUTION SP3-C • EVOLUTION SP4-E/N + FEEDER EVO-4R/N •...

  • Page 31: Wire Feeder Control Panel (Not Used With Evolution Sp3-C)

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.4. Wire feeder control panel (not used with EVOLUTION SP3-C) The FEEDER EVO-4R/N wire feeder panel has 2 keys, 2 encoders and 7 LEDs in the upper section and 4 keys and 5 LEDs in the lower section.

  • Page 32: Switching On The Welding Machine

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N CRATER 4T LED 4T switched on - LED CRATER switched on 1. 1When the TORCH TRIGGER is pushed the arc ignites and the parameters assume the values for the “initial crater”.

  • Page 33: Language Selection

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.6. Language selection SX KEY DX KEY VISION SCREEN MENU KEY ENTER/MEM KEY ENCODER KNOB - SX ENCODER KNOB - DX “EVOLUTION” control panel On the EVOLUTION SCREEN the DEFAULT language set by is ENGLISH.

  • Page 34: Welding Process Selection Menu (Process)

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.8. WELDING PROCESS SELECTION Menu (PROCESS) “EVOLUTION” CONTROL PANEL To access the PROCESS SELECTION Menu (PROCESS) push the MENU KEY. MENU KEY ENTER/MEM KEY ENCODER KNOB - SX...

  • Page 35: Mig-Mag, Mig Pulse/Dual Pulse

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N “FEEDER EVO-4R/N” CONTROL PANEL (not used with EVOLUTION SP3-C) is not possible to access the PROCESS SELECTION Menu (PROCESS) via the FEEDER EVO-4R/N control panel. 6.5.9. MIG-MAG, MIG pulse/dual pulse 6.5.9.1.

  • Page 36: Special Functions Menu (Set Up Fx)

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N “FEEDER EVO-4R/N” CONTROL PANEL (not used with EVOLUTION SP3-C) To access the WELDING MODE SELECTION Menu (MODE) push the WELDING MODE SELECTION KEY. WELDING MODE SELECTION LED...
  • Page 37 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N “FEEDER EVO-4R/N” CONTROL PANEL (not used with EVOLUTION SP3-C) To access the SPECIAL FUNCTIONS Menu (SET UP Fx) push the SPECIAL FUNCTIONS (FX) KEY. PARAMETER DISPLAY SCREEN - V...
  • Page 38 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Adjustable special functions Special function PARAMETER PARAMETER DISPLAY Welding mode DISPLAY Screen - V Screen - A INITIAL ARC LENGTH -30 - +30 (*) (*) (*) (*) INITIAL CRATER TIME 1.0s...
  • Page 39 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Adjustable special functions Special function PARAMETER PARAMETER DISPLAY Welding mode DISPLAY Screen - V Screen - A SECOND SLOPE F33 *** (0 - 100) • • •...
  • Page 40 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N The SPECIAL FUNCTIONS (Fx) for the MIG-MAG manual process correspond to the feeder (when fitted) as follows: Adjustable special functions Special function PARAMETER PARAMETER DISPLAY Welding mode...

  • Page 41: Pre-Setting

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.9.4. PRE-SETTING “EVOLUTION” CONTROL PANEL SX KEY DX KEY MENU KEY ENCODER KNOB - SX ENCODER KNOB - DX Used to access the PROCESS SELECTION Menu (PROCESS) and subsequent MENU KEY menus, as applicable.

  • Page 42: Welding

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N WIRE KEY Activates loading of the wire. WELDING MODE SELECTION Scrolls the various welding modes in succession. WELDING MODE SELECTION The LED unit indicates the welding mode selected according to the EVO- LUTION SCREEN.

  • Page 43: Hold (Real Current Reading)

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.9.6. HOLD (real current reading) When welding ends the fields in the display must show the same values that were displayed during welding, with the difference that they are now values defined as . In this phase the EVOLUTION SCREEN shows the HOLD box highlighted, while on the FEEDER EVO-4R/N panel the HOLD FUNCTION LED flashes until the end of the HOLD Function.

  • Page 44: Double Feeder

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Rotate the ENCODER KNOB - SX the wire loading speed can be changed from 1,0 to 22,0 (default 8,0). The other keys and knobs are not active.

  • Page 45: Mma

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.10. MMA Select the MMA welding process by using the MENU KEY. 6.5.10.1. PROGRAM SELECTION Menu (PROGRAM) “EVOLUTION” CONTROL PANEL To access the PROGRAM SELECTION Menu (PROGRAM) push the MENU KEY.
  • Page 46 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N “FEEDER EVO-4R/N” CONTROL PANEL (not used with EVOLUTION SP3-C) To access the SPECIAL FUNCTIONS Menu (SET UP Fx) push the SPECIAL FUNCTIONS (FX) KEY. PARAMETER DISPLAY SCREEN - V...

  • Page 47: Pre-Setting

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.10.3. PRE-SETTING “EVOLUTION” CONTROL PANEL DX KEY MENU KEY ENTER/MEM KEY ENCODER KNOB - SX ENCODER KNOB - DX MENU KEY Used to access the PROCESS SELECTION Menu (PROCESS) and subse- quent menus, as applicable.

  • Page 48: Welding

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.10.4. WELDING When welding takes place the fields in the displays show the same values as those included for pre-setting with the difference that now they are those measured.

  • Page 49: Hold

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.10.5. HOLD When welding ends the fields in the display must show the same values that were displayed during welding, with the difference that they are now values defined as HOLD. In this phase the EVOLUTION SCREEN shows the HOLD box highlighted, while on the FEEDER EVO-4R/N panel the HOLD FUNCTION LED flashes until the end of the HOLD Function.

  • Page 50: Attivazione Del Dispositivo Vrd

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.10.6. ATTIVAZIONE DEL DISPOSITIVO VRD The Voltage Reduction Device (VRD) is a safety device that reduces voltage. It prevents voltages forming on the output termi- nals that may pose a danger to people. The standard settings and those defined beforehand by do not provide for the VRD to be active on the welding machine and so the EVOLUTION SCREEN does not normally provide any indication.

  • Page 51: Tig Lift

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.11. TIG LIFT Select the TIG LIFT welding process by using the MENU KEY. 6.5.11.1. SPECIAL FUNCTIONS Menu (SET UP Fx) TIG LIFT “EVOLUTION” CONTROL PANEL To access the SPECIAL FUNCTIONS Menu (SET UP Fx) push the MENU KEY.

  • Page 52: Pre-Setting

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N The SPECIAL FUNCTIONS (Fx) related to the TIG LIFT process correspond as follows to those on the wire feeder: Adjustable special functions Special function PARAMETER DISPLAY PARAMETER DISPLAY Screen - V...

  • Page 53: Welding

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N “FEEDER EVO-4R/N” CONTROL PANEL (not used with EVOLUTION SP3-C) PARAMETER DISPLAY SCREEN - V PARAMETER DISPLAY SCREEN - A PARAMETER SELECTION LED - V PARAMETER SELECTION LED - A...

  • Page 54: Hold

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N “FEEDER EVO-4R/N” CONTROL PANEL (not used with EVOLUTION SP3-C) 6.5.11.4. HOLD TIG LIFT When welding ends the fields in the display must show the same values that were displayed during welding, with the difference that they are now values defined as HOLD.

  • Page 55: Job/Sequenze

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.12. JOB/SEQUENZE 6.5.12.1. Creating and saving / editing and overwriting a JOB/SEQUENCES (*) JOB/SEQUENCES “EVOLUTION” CONTROL PANEL SX KEY DX KEY VISION SCREEN MENU KEY ENTER/MEM KEY...
  • Page 56 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N CREATING AND SAVING A JOB To create and save a JOB (welding point) proceed as follows: • During any welding process and at any time, once you have acquired the nec- essary parameters, hold the ENTER/MEM KEY down for 3 consecutive seconds.

  • Page 57: Job/Sequences Selection Menu

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.12.2. JOB/SEQUENCES SELECTION Menu JOB/SEQUENCES WARNING: All the parameters saved within a JOB/SEQUENCE (including SPECIAL FUNCTIONS (Fx)) can be viewed but not edited! “EVOLUTION” CONTROL PANEL To access the JOB/SEQUENCES SELECTION Menu push the MENU KEY.
  • Page 58 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N “FEEDER EVO-4R/N” CONTROL PANEL (not used with EVOLUTION SP3-C) HOLD Function LED PARAMETER DISPLAY SCREEN - V PARAMETER DISPLAY SCREEN - A PARAMETER SELECTION KEY - V...

  • Page 59: Pre-Setting

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.12.3. PRE-SETTING JOB/SEQUENCES WARNING: All the parameters saved within a JOB (including SPECIAL FUNCTIONS (Fx)) can be viewed but not edited! “EVOLUTION” CONTROL PANEL SX KEY DX KEY...
  • Page 60 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N “FEEDER EVO-4R/N” CONTROL PANEL (not used with EVOLUTION SP3-C) PARAMETER DISPLAY SCREEN - V PARAMETER DISPLAY SCREEN - A PARAMETER SELECTION KEY - V SPECIAL FUNCTIONS (FX) KEY...

  • Page 61: Welding

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.12.4. WELDING JOB/SEQUENCES WARNING: All the parameters saved within a JOB (including SPECIAL FUNCTIONS (Fx)) can be viewed but not edited! “EVOLUTION” CONTROL PANEL SX KEY DX KEY...
  • Page 62 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N “FEEDER EVO-4R/N” CONTROL PANEL (not used with EVOLUTION SP3-C) HOLD Function LED PARAMETER DISPLAY SCREEN - V PARAMETER DISPLAY SCREEN - A PARAMETER SELECTION KEY - V...

  • Page 63: Hold

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.12.5. HOLD JOB/SEQUENCES When welding ends the fields in the display must show the same values that were displayed during welding, with the difference that they are now values defined as HOLD. In this phase the EVOLUTION SCREEN shows the HOLD box highlighted, while on the FEEDER EVO-4R/N panel the HOLD FUNCTION LED flashes until the end of the HOLD Function.

  • Page 64: Error Condition

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.13. Error condition WARNING: Under normal conditions of use it is not possible to open the “ERROR LOG Menu” display since the alarm message appears instantaneously on the EVOLUTION SCREEN as soon as the problem arises on the weld- ing plant.
  • Page 65 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N “FEEDER EVO-4R/N” CONTROL PANEL (not used with EVOLUTION SP3-C) HOLD Function LED PARAMETER DISPLAY SCREEN - A PARAMETER DISPLAY SCREEN Displays the error message (e.g. Err.). PARAMETER DISPLAY SCREEN Shows the alarm code (e.g.

  • Page 66: Setup Menu

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.14. SETUP Menu “EVOLUTION” CONTROL PANEL To access the SETUP Menu hold down for at least 5 consecutive seconds the SX KEY. SX KEY ENTER/MEM KEY MENU KEY...

  • Page 67: Job Edit

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.14.1. JOB EDIT SETUP Menu The purpose of this menu is to allow the operator to copy or delete a JOB (automatic welding point) entered previously. To access the JOB EDIT Menu from the SETUP Menu: •...

  • Page 68: Seq Edit

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.14.2. SEQ EDIT SETUP Menu The purpose of this menu is to allow the operator to create, copy, overwrite, or delete a welding sequence. To access the SEQ EDIT Menu from the SETUP Menu: •...
  • Page 69 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N CREATING A SEQUENCE Use the ENTER/MEM KEY to create a new sequence. Use the SX KEY to add the JOB selected using the ENCODER KNOB - DX to the section of the sequence selected using the ENCODER KNOB - SX.
  • Page 70 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N If the sequence position chosen is already in use, when the ENTER/MEM KEY is pushed the image to the left is displayed. Push the SX KEY and sequence4 6 will be replaced by sequence 4, whereas the DX KEY cancels everything.

  • Page 71: Password

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.14.3. PASSWORD SETUP Menu The purpose of this menu is to allow the operator to enter a PASSWORD for accessing the SETUP Menu. To access the PASSWORD Menu from the SETUP Menu: •...

  • Page 72: Blocks

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N DELETING THE EXISTING PASSWORD WARNING: This operation is only possible after having accessed the SETUP Menu using the password you wish to delete! To delete the existing PASSWORD proceed as follows: Make sure the EVOLUTION SCREEN shows the PASSWORD entered previously (a number that must be between 001 and 999).

  • Page 73: Config

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Block type Description LEVEL 1 PARTIAL BLOCK The operator can weld using the parameters set prior to the block and may make adjustments and/or changes to the welding parameters us- ing the knobs on the control panels on the welding machine and the wire feeder (if fitted).
  • Page 74 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Advanced function Description Indicates the languages that can be set for the EVOLUTION SCREEN. LANGUAGE As regards the procedure for selecting a language on the EVOLUTION SCREEN see the relevant paragraph in the manual (“Language Selec- tion”).

  • Page 75: Advanced Setup Menu

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.15. ADVANCED SETUP Menu “EVOLUTION” CONTROL PANEL Tasto SETUP/SX Tasto DX Display EVOLUTION Tasto MENU Tasto ENTER/MEM Manopola ENCODER - SX Manopola ENCODER - DX To access the ADVANCED SETUP Menu from any point on the control panel: •...

  • Page 76: Advanced Config

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N “FEEDER EVO-4R/N” CONTROL PANEL (not used with EVOLUTION SP3-C) It is not possible to access the ADVANCED SETUP Menu and all the related sub-menus using the “FEEDER EVO- 4R/N”...

  • Page 77: Advanced Mode

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Advanced function Description By rotating the ENCODER KNOB - DX (this operation does not re- ENERGY SAVING quire confirmation) it is possible to choose the energy saving mode you prefer from the 3 available for the welding plant: •...
  • Page 78 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Within the ADVANCED MODE Menu it is possible, by rotating the ENCODER KNOB - SX, to choose the advanced welding mode re- quired from the 4 available (according to the welding process selected) and this can be AC- TIVATED (this operation does not require confirmation) by rotating the ENCODER KNOB - DX.

  • Page 79: Equipment Layout

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Advanced function Description MODO TIG LIFT If activated, this function makes an additional welding mode known as TIG LIFT TORCH TRIGGER available to an operator using the TIG LIFT welding process.
  • Page 80 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Within the EQUIPMENT LAYOUT Menu, it is possible, by rotating the ENCODER KNOB - SX, to select the compo- nent of the welding plant, while by rotating the ENCODER KNOB - DX, you can decide the type of connection required (e.g.
  • Page 81 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Advanced function Description LATO USCITA FILO 1 / Shows the exit point (right or left) of the welding rod away from the LATO USCITA FILO 2 control panel.
  • Page 82 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Advanced function Description TORCH TYPE 1 / TORCH TYPE 2 Used to set the TORCH TYPE 1/2 that will subsequently be connected to the welding plant. This operation must be done in order to size the plant correctly and as a result, the welding parameters.
  • Page 83 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Advanced function Description PUSH PULL 1 / Indicates the PUSH PULL type used. PUSH PULL 2 When the knob is moved to the OFF position the push pull is not man- aged.
  • Page 84 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N MENU KEY ENTER/MEM KEY ENCODER KNOB - SX ENCODER KNOB - DX When in the CONFIG menu, rotate the ENCODER KNOB - SX to select activation of robot configuration.
  • Page 85 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Advanced function Description ROBOT REG. MODE (ROBOT ASS. CURRENT - In this mode, a MINIMUM ROBOT ANALOGUE V - MAX- REGULATION MODE) IMUM ROBOT ANALOGUE V (*) input corresponds to a current supplied of 0-500A.
  • Page 86 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Advanced function Description ROBOT PULSE FREQ. (ROBOT PULSE NOT ACTIVE - In this mode, PULSATION FREQUENCY regulation is ac- FREQUENCY) tive, via the welding machine’s panel. ACTIVE - In this mode, PULSATION FREQUENCY regulation is active, via the robot interface board.
  • Page 87 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Advanced function Description MIN. ROBOT ANALOG VOLTAGE These parameters are used to set the maximum and minimum volt- age settings used to control the robot board’s analogue inputs.

  • Page 88: Factory Reset

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Per uscire dal Menu EQUIPMENT LAYOUT e ritornare al Menu IMPOSTAZIONI AVANZATE: • Push the MENU KEY. 6.5.15.4. FACTORY RESET SETUP Menu The purpose of this menu is to allow the operator to return the welding machine partially or totally to the factory settings.
  • Page 89 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Function Description COUNTER ALARMS RESET Used to reset the counters for all the alarms (Curr. - Tot see ERROR LOG Menu) that have occurred in the welding plant.

  • Page 90: Info

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.15.5. INFO SETUP Menu The purpose of this menu is to allow the operator to know what version of the software has been loaded into each component that is part of the welding plant.
  • Page 91 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Software Description This indicates the serial number for the microprocessor contained in the digital interface board. This is the serial number required for load- ing special functions at additional cost.

  • Page 92: Network

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Software Description ENABLED OPTIONS The special programs enabled, specifically: • PULSED • ECP estended curves package • EVO.COLD • EVO.PIPE • EVO.POWER • EVO.ULTRASPEED The contents of thus menu are for information only, the operator cannot change anything they can only read the information con- tained by scrolling the various options available in the menu by rotating the ENCODER KNOB - SX.

  • Page 93: Weld Log

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Function Description NETMASK This indicates the sub-network template number to which the weld- ing machine has been assigned. GATEWAY This indicates the gateway number to which the welding machine has been assigned.

  • Page 94: Error Log

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.5.15.8. ERROR LOG SETUP Menu The purpose of this menu is to allow the operator to know, interpret, and understand error conditions that have occurred or may be encountered on the welding plant.
  • Page 95 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Within the menu, by rotating the ENCODER KNOB - SX it is possible to scroll the errors (also indicated in the table below), view them and select them.
  • Page 96 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Error Error Error description and possible diagnosis condition code WIRE FEEDER MISSING NON automatic reset error. Check that the WIRE FEEDER - OBLIGATORY function is included within the AD- VANCED SETUP Menu / EQUIPMENT LAYOUT.
  • Page 97 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Error Error Error description and possible diagnosis condition code MMA DEFAULTS MISSING E1.6 NON automatic reset error. Immediately contact technical assistance dept. Error visible on EVOLUTION SCREEN ONLY in the event of a fault and NOT in the ERROR LOG Menu.
  • Page 98 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Error Error Error description and possible diagnosis condition code JOBS WRONG E4.1 NON automatic reset error. Immediately contact technical assistance dept. Error visible on EVOLUTION SCREEN ONLY in the event of a fault and NOT in the ERROR LOG Menu.
  • Page 99 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Error Error Error description and possible diagnosis condition code MIG MANUAL PROGRAMS MISSING E5.5 NON automatic reset error. Immediately contact technical assistance dept. Error visible on EVOLUTION SCREEN ONLY in the event of a fault and NOT in the ERROR LOG Menu.
  • Page 100 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Error Error Error description and possible diagnosis condition code E8.3 NO GAS FLOW Error reset by a command from the robot’s board (see robot interface manual). E8.4 NO H2O FLOW Error reset by a command from the robot’s board (see robot interface manual).

  • Page 101: Start-Up

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 6.6. START-UP 7. MAINTENANCE After turning on machine or line power, conduct a 7.1. MACHINE ISOLATION careful visual inspection of the entire machine and make sure that no persons or material are obstruct-...

  • Page 102: Routine Maintenance

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 7.4. ROUTINE MAINTENANCE ATTENTION: These operations, although simple, must be performed by a Qualified and Authorised General requirements Technician. The machine is designed to minimise routine main-...

  • Page 103: Accessories And Spare Parts

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 8. ACCESSORIES AND SPARE repaired welding machines, in which some com- ponents have been replaced or modified, must be PARTS marked so that the person who carried out the re- pair can be identified.

  • Page 104: Additional Instructions

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 9. ADDITIONAL INSTRUCTIONS There are 2 ways to discard DOMESTIC WEEE: a) If you decide to buy a new equivalent equipment, the user can deliver it to the distributor, who will 9.1.

  • Page 105: Annexes

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 10. ANNEXES 10.1. WIRING DIAGRAMS EVOLUTION SP3-C wiring diagram 1.995.241 EN - Rev. 1.1...
  • Page 106 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N EVOLUTION SP4-E/N SP5-E/N-E wiring diagram 1.995.241 EN - Rev. 1.1...
  • Page 107 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N EVOLUTION SP4-E/N / SP5-E/N RESTAPI wiring diagram 1.995.241 EN - Rev. 1.1...
  • Page 108 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N FEEDER EVO-4R/N wiring diagram 1.995.241 EN - Rev. 1.1...

  • Page 109: Spare Parts

    EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 10.2. SPARE PARTS EVOLUTION SP3-C 1.995.241 EN - Rev. 1.1...
  • Page 110 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Pos. Code Description Pos. Code Description SW.801012 FEEDER 4R 5.005.051/MG POTENTIOMETER D. 22 5.725.035 RADIATOR 3.100.144 FRONTAL INTERFACE BOARDS 1.020.011 1.090.015 MAT EVOLUTION 3.022.004 ELECTROPUMP 3.100.139 POWER SOURCE BOARD 1.014.082...
  • Page 111 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N EVOLUTION SP4-E/N 48 11 1.995.241 EN - Rev. 1.1...
  • Page 112 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Pos. Code Description Pos. Code Description 1.997.004 LOCK 1.019.012 WHEEL D. 250 1.997.063 HINGE 6.630.810 POWER CABLE 4 x 6,0 mmq SW.801012 FEEDER 4R 1.016.004 CABLE GLAND 1.019.009...
  • Page 113 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N EVOLUTION SP5-E/N 48 11 1.995.241 EN - Rev. 1.1...
  • Page 114 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N Pos. Code Description Pos. Code Description 1.997.004 LOCK 1.019.012 WHEEL D. 250 1.997.063 HINGE 6.630.810 POWER CABLE 4 x 6,0 mmq SW.801012 FEEDER 4R 1.016.004 CABLE GLAND 1.019.009...
  • Page 115 EVOLUTION SP3-C / EVOLUTION SP4-E/N / EVOLUTION SP5-E/N FEEDER EVO-4R/N / G.R. EVO/N 1.995.241 EN - Rev. 1.1...
  • Page 116 SINCOSALD S.r.l Sede Legale – Amministrativa via della Fisica, 26/28 20864 Agrate Brianza (MB) Italy Tel: +39 039 641171 r.a. Fax: +39 039 6057122 export@sincosald.it www.sincosald.it...

This manual is also suitable for:

Evolution sp3-cEvolution sp5-e/nFeeder evo-4r/nG.r. evo/n

Table of Contents