jbc DT530 Instruction Manual
  1. Manuals
  2. Brands
  3. jbc Manuals
  4. Power Tool
  5. DT530
  6. Instruction manual

jbc DT530 Instruction Manual

Angled desoldering iron
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
DT530
Angled Desoldering Iron

Advertisement

Table of Contents
loading

Related Manuals for jbc DT530

Summary of Contents for jbc DT530

  • Page 1 INSTRUCTION MANUAL DT530 Angled Desoldering Iron...

  • Page 2: Packing List

    Manual ..........1 unit Ref. 0032496 Already assembled: Ref. D530003 Through-Hole Desoldering Tip Ø 1 (1x) - Ref. DTH-A Heating Element for DT530 - Glass solder-collector with gaskets and filters (see next page for references) Box with Accessories ....1 box Ref.
  • Page 3 Ref. DT20 80 mm 60 mm 50 mm Spanner ......1 unit Wool Filter Metal Filter Ref. DT50 for DT530 ......1 set for DT530 ......1 set 40 mm Ref. DT10 Ref. DT11 (contains 10 filters) (contains 10 filters) Heat-Resistant Cleaning Brush .....
  • Page 4 SMD rework. It must be connected to an electric or pneumatic desoldering module and to the tool stand. JBC Most Efficient Soldering System and the suction power from MSE or MVE pumps ensure optimal quality of work.
  • Page 5 para manuales - color gris 200 mm 130 mm 130 mm Work Sleep Hibernation 100 mm Long period in the stand 80 mm When the tool is lifted from When the tool is returned to the After longer periods of inactivity, the stand, the tip will heat stand, the temperature falls to the tool goes into Hibernation...

  • Page 6: Tip Cleaning

    Brass Wool Very effective cleaning method. Leaves a small layer of solder on the tip preventing oxidation between cleaning and rewetting. If the tip is very dirty, JBC recommends cleaning it first with the wiper to remove excess solder. Wiper The integrated wiper offers different ways to clean the tips.
  • Page 7 100 mm Removing At least 250 ºC Use JBC’s spanner to unscrew the tip (1). The tip will remain attached to the spanner 80 mm so that it can be moved safely.
  • Page 8 Cleaning the Glass Solder-Collector Be careful when handling the solder collector, it can be hot. Let it cool down first. Suction Tube Glass Desoldering Connector Solder-Collector Iron Suction Tube Heating Element Guard The glass solder-collector is designed to be While holding the tool with one hand down cleaned and reused.
  • Page 9 para manuales - color gris 200 mm 130 mm 130 mm Cleaning the Glass Solder-Collector Wool Metal Cleaning Filter Filter Brush 100 mm Cleaning 80 mm Brush Use the provided cleaning brush to push both Clean the glass tube using the cleaning brush. 60 mm filters out of the tube.

  • Page 10: Changing The Heating Element

    Inserting the Glass Solder-Collector into the Tool Frontal Suction Tube Gasket Connector Rear Slot Heating Element Insert the collector group with its front gasket Then bring it down until the suction tube onto the heating element. connector fits into the rear slot of the heating element guard.
  • Page 11 para manuales - color gris 200 mm 130 mm 130 mm 100 mm 80 mm Heating Element Fixing Screw Loosen the fixing screw. Then pull out the heating element. 60 mm Left-hand / right-hand use: Metal Bushing “a” for Heat. Elem. Edge right-hand use 50 mm 40 mm...

  • Page 12: General Maintenance

    - The wool, filter and gaskets of the solder-collector should be periodically checked and replaced when worn or clogged with solder residues. - Replace any defective or damaged pieces. Use original JBC spare parts only. - Repairs should only be performed by a JBC authorized technical service.
  • Page 13 para manuales - color gris 200 mm Duct Maintenance 130 mm 130 mm - To avoid clogging or pressure loss, it is necessary to carry on regular maintenance on the tips and to be attentive to the condition of solder-collectors, gaskets and filters. Introduce the cleaning rod also Tip Cleaning from the top side of the tip...
  • Page 14 Safety It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion. - Do not use the device for any purpose other than soldering/desoldering or rework. Incorrect use may cause fire. - Do not work on electrically live parts. - The tool should be placed in the stand when not in use in order to activate the Sleep Mode.
  • Page 15 para manuales - color gris 200 mm Notes 130 mm 130 mm 100 mm 80 mm 60 mm 50 mm 40 mm...

  • Page 16: Specifications

    9.65 x 7.28 x 1.77 in / 0.91 lb Complies with CE standards. ESD safe. Warranty JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse.

Table of Contents