Listening To Other Sources - Sanyo DC-DA280 Instruction Manual

Automatic/Manual I tuning
1. Press the FUNCTION button to select TUNER. The radio frequency
appears.
2. Press the TUNER/BAND button to select FM, MW or LW.
Automatic tuning
Press the TUNING - or TUNING + button for at least 1 second to tune
in a station. The unit will scan up or down the band and receive the
next receivable station. Press the button again to continue.
- The Pi or Hdd button on the remote control can also be used.
Manual tuning
Press the TUNING - or TUNING + button briefly until the desired
frequency is displayed.
To preset stations (Remote control only)
Up to 24 stations for FM band, 12 stations for MW band, and up to 4
stations for LW band can be preset.
1. Tune in the station to be preset as described above.
2. Press the MEMORY button on the remote control..
3. Press the PRESET - or PRESET + button on the front panel (or
PRESET button on the remote control) to select the channel number
to be preset.
4. While "PROG." is blinking, press the MEMORY button. "PROG."
disappears.
- Inthis example, "103.25 MHz" FM station is preset on FM channel
9.
- The number buttons on the remote control can also be used. In
this example, press O, then 9 after the step 2 above.
Beara a eee
1. Press the FUNCTION button to se-
lect "TAPE".
2. Press the cassette holder (EJECT
portion) to open it.
3. Load the cassette.
After loading the cassette, push the
cassette holder (EJECT portion) back
into position.
4. Press the TAPE button to begin play-
back.
5. Press the O button to stop playback
at any time. Press it again to remove
the cassette.
When the end of the tape has been
reached, automatic stop will be acti-
vated.
ee etree te ee E ren ee eRe Cee Emre er eee ere mee eee ree Sia RROD
1. Press the FUNCTION button to select "LINE".
Note:
If the next step is not taken within 10 seconds while performing steps
2-4, "PROG." disappears and the preset operation is cancelled.
Press the MEMORY button on the remote control to continue.
5. Repeat steps above to add more preset stations.
- When presetting a new station, the previous preset station is
cleared.
Listening to preset stations
1. Press the TUNER/BAND button to select FM, MW or LW.
2. Press the PRESET - or PRESET + button on the front panel (or
PRESET button on the remote control) to select the desired channel
number. The selected channel number appears briefly.
- The number buttons on the remote control can also be used.
Press two number buttons within 2 seconds.
To receive FM stereo broadcasts
"ST" appears when an FM stereo broadcast Is received in the stereo
mode.
Make sure the reception mode is in stereo. or else, press the FM MODE
button.
- If the signal from an FM stereo station is weak and reception is poor,
press the FM MODE button to change to the mono mode. The
reception may be improved, but the sound will be monaural.
When beat interference is heard
A high-pitched noise called "beat" is sometimes heard during reception
of radio broadcasts. If this occurs.
1. Press the MEMORY button on the remote control.
2. When "PROG." is blinking, press the FM MODE button to select "bc-
A" or "bc-b". Select the setting that gives the best results.
Changing the MW reception frequencies
It is not necessary to perform this procedure in the Europe.
1. Press the TUNER/BAND button to select "MW".
2. While pressing the O button on the front panel, press the [>> button
on the front panel.
522 - 1611 kHz (9kHz steps) 520 - 1610 kHz (10 kHz steps)
Note:
- Use the normal tape (TYPE 1).
- Endless tapes cannot be used.
- Donotuse 0-100 (or longer) tapes. They may jam in the mechanism.
Fast forward and rewind
Press the KK or >> button. When the desired location has been
reached, press the U button.
LISTENING TO OTHER SOURCES _
2. Follow the instructions supplied with the Video/Auxiliary equipment.