Ozobot COLOR CODE Manual page 6

Defined
Speed
Speed codes change your Ozobot's velocity
from Short Super Slow (slowest) to Nitro
Boost (fastest).
Short Super Slow
R G B
A three–second dose of super slow speed.
Slow
R BK R
A slow speed command is effective until the bot
reads a new speed code or is turned off.
Cruise
G BK G
The default speed command.
Fast
B BK B
A high speed command effective until the bot
reads a new speed code or is turned off.
Turbo
B G B
An extra high speed command effective until
the bot reads a new speed code or is turned off.
Nitro Boost
B G R
A three–second dose of Ozobot's highest speed.
Short
Nitro Nitro
Super Slow Cruise Fast Turbo
Boost Boost
Slow
Slowest Default Fastest
Cool Moves
Cool Move codes tell your Ozobot to bust
a move!
Tornado
R G R G
A command to spin around four times at
increasing speed, then continue following the
line in the same direction.
Direction
Direction codes tell your Ozobot what to do
at an intersection.
Left at Intersection
G BK G
A command to turn left at the next intersection.
Straight at Intersection
B BK R
A command to continue straight at the next
intersection.
Right at Intersection
B R G
A command to turn right at the next
intersection.
Line Switch Left
G R G
A command to immediately turn 90-degrees to
the left, move forward to a new line, then make
a random turn to follow along the new line.
Line Switch Straight
G B G
A mid–line command to continue straight after
the line ends. The code will not work if Ozobot
encounters an intersection before the line ends.
Line Switch Right
R G R
A command to immediately turn 90-degrees to
the right, move forward to a new line, then make
a random turn to follow along the new line.
U–Turn
B R B
A mid-line command to turn around
180-degrees and follow the same line in the
opposite direction.
U–Turn (Line End)
B R
A line–end command to turn around 180-degrees
and follow the line in the opposite direction.
Ozobot's default intersection behavior is random.
If a given turn, i.e. 'Go Left' is not possible, Ozobot
defaults back to random behavior.
Zigzag
B BK G R
A command to sway right-left-right-left while
moving forward, then continue moving straight.
Spin
G R G R
A command to spin around twice at a consistent
speed, then continue following the line in the
same direction.
Counters
Counter codes tell your Ozobot to count five
intersections, turns, or line color changes.
Enable X–ing Counter
G R B G
A command to make your Ozobot stop following
lines after it crosses five intersections ('T' or
'+' intersections). After the fifth intersection,
Ozobot executes a "done" maneuver, stops
following the line, and blinks red.
Enable Turn Counter
R B G B
A similar command to the Enable X–ing Counter,
except that Ozobot only counts intersections
where it makes a turn. It will not count
intersections where it continues straight.
Ozobot can randomly choose to go straight at
an intersection, or be commanded to go straight
with a "Straight at Intersection" code.
Enable Path Color Counter
R G B R
A command to make your Ozobot stop following
lines after it reads five color changes in the line.
If the line Ozobot is following transitions from
red to green, it counts as one color change.
Transitions to and from black lines are not
counted, and color segments less than two
centimeters in length are not counted.
Enable Point Counter
R B R G
A command that tells your Ozobot to count
point codes down from five. Each time Ozobot
reads a "Point –1" code it counts down. After
the fifth "Point –1" code Ozobot will make a
"done" maneuver, stop following lines, and blink
red. You can add more to the total count (not to
exceed five) with "Point +1" codes. You can reset
Ozobot by turning it off, then on.
• Point +1
R B G
• Point –1
G B R
Backwalk
R G BK B
A command to quickly turn 180-degrees,
wiggle backwards for one second, then turn
180-degrees again and continue following
the line in the same direction.
Ozo Edu, Inc. •
ozobot.com
Timer
Timer codes tell your Ozobot to pause or
count seconds.
Pause (3 sec.)
R B R
A command to stop moving for three seconds,
then continue with default behavior.
Timer On (30 sec. to stop)
R BK B G
A command to make your Ozobot countdown
from 30 sec., but continue to move and read
codes while counting down. Ozobot will flash
its light(s) at a rate of one flash/sec., flash
rapidly to signify time is up, then shut off.
Timer Off
G R B G
A command to stop counting down seconds
and return to default behavior.
Wins/Exits
Win/Exit codes tell your Ozobot to celebrate
its success, then either start over or stop.
Win/Exit (Play Again)
G B
A command to perform a "success" animation,
then continue to follow the line.
Win/Exit (Game Over)
G R
A command to perform a "success" animation,
then stop following the line.
• • Rev 2-23
support@ozobot.com 6