Summary of Contents for Cervis Wireless SmaRT HH-18 Series
Page 1
HH-x18 User Manual U132.0.0 Ó2023 Cervis, Inc.
Page 2
SmaRT HH-x18 This document is the property of Cervis, Inc. and cannot be copied, modified, e-mailed, or reproduced without the express prior written consent of Cervis, Inc. Cervis, Inc. reserves the right to change this manual or edit, delete, or modify any information without prior notification.
Table of Content ........................... i List of Figures ..........................i List of Tables ..........................i Definitions/Notes ......................... ii Cervis, Inc. Safety Precautions ....................1 1.0 SmaRT HH-x18 Portable Unit ..................... 3 1.1 Handheld Features ......................3 1.2 SmaRT HH-x18 Handheld Battery Installation ............... 4 1.3 Low Battery Warning .......................
SmaRT HH-x18 Definitions/Notes Associate/Association Mode whereby SmaRT handhelds and base units are paired for operation (identities [ID’s] exchanged). This mode is used to commission spare handhelds or base units. Dissociation The process of decommisioning a handheld from a base unit’s identity memory. DSSS Direct Sequence Spread Spectrum;...
User Manual Cervis, Inc. Safety Precautions ü Read and follow all instructions. Failure to abide by Safety Precautions may cause equipment failure, loss of authority ü to operate the equipment, and personal injury. Use and maintain proper wiring. Follow equipment manufacturer instructions.
Page 6
The following applies only to SmaRT HH-x18 Handheld remote control systems. RoHS Compliance Statement Cervis, Inc. complies with the requirements of Restriction of Hazardous Substances (RoHS) Specification based on in-house practice and declaration of compliance from our vendors. For additional information concerning RoHS compliance, please contact Cervis, Inc.
Single or dual On and Off button • Eight LED indicators • Low voltage warning LED indication and critical low voltage auto-shutdown • Rugged high impact polymer/polycarbon/stainless steel enclosure • Removable bumper option • Operates at 3.0-6.0 VDC (uses four “AA” cell batteries) Ó2023 Cervis, Inc.
1.2 SmaRT HH-x18 Handheld Battery Installation The handheld remote operates between 3.0 to 6.0 VDC powered by four factory supplied 1.5 V “AA” cell batteries. Cervis, Inc. recommends having fresh spare batteries on hand at all times that the system is in use.
1.4 Low Battery Auto-Shutdown When the handheld battery voltage reaches 3.0 V, the unit will deactivate. The four AA batteries must be replaced before the handheld remote can be used. Ó2023 Cervis, Inc.
SmaRT HH-x18 2.0 SmaRT HH-x18 Operation 2.1 SmaRT OO-x18 Operation Turn ON the Unit Power the remote ON (button 1) by pressing the Green-and-White ON button Turn OFF the Unit Turned OFF (button 3) the remote by pressing and holding the Red-and-White OFF button for about 3 seconds.
3. Press and hold button 3 (DO) or the OFF button (OO), then press and hold the ON button. The left side LEDs will activate for one second. 4. Wait until the TX LED starts blinking and the BATT LED turns on solid. Then power on the base unit. Ó2023 Cervis, Inc.
Page 12
SmaRT HH-x18 5. If dissociation is successful, all LEDs will activate. Button 3 (DO) or the OFF button (OO) and the ON button can now be released. U132.0.0...
1 second. 3. Pressing and releasing Button 15 will decrease the timeout by 1 count. When 1s, timeout will roll over to 30 seconds. 4. Timeout values are 1 – 30 seconds. Display will represent current value. Ó2023 Cervis, Inc.
SmaRT HH-x18 5.0 Specifications Table 1 SmaRT HH-x18 Specifications Item Description Power +3.0 to +6.0 VDC Batteries Four “AA” cell Battery Life 70 hours Auto-shutdown 10’ of button inactivity Environment Operating Temp –20° C to 55° C (–4° F to 131° F) Storage Temp –40°...
Need help?
Do you have a question about the Wireless SmaRT HH-18 Series and is the answer not in the manual?
Questions and answers