Table of Contents
Advertisement
Pull the Cord-holder, get the AC Power Cord;
ios
;
cat AC Power Cord inta Power Base:
wy
@ When use for steam iron, the iron should be preheated every 30 seconds.
* Different time for different condition.
AC Power Cord
AC Power Cord Adapter
Steam/ Dry Selector (switch as the following )
Light
steam:
for thin or delicate fabrics
requiring a small amount of
steam.
Regular steam:
for fabrics requiring a lot of
steam ( i.e.thick materials,
Move the Steam/Dry Selector to Dry ( 3€ ) position.
~»
items with stubborn wrinkles.)
Press the Water Tank Release Button; take out the Water Tank.
eae the Water Fill Cover. Fill the Water Tank up to " 满 水 (MAX) " line.
Dry(3)
Lightsteam
Regular steam
(D Observe the volume of water at upright position, do not overfill above " 满 水 (MAX)"
O How to use the Jet of Steam feature
© U
tap water
a) For fabrics of thick materials and with stubborn wrinkles,
© While fill Water Tank with water, don't plug the AC Power Cord into electrical outlet.
and cleaning the steam vents at the same time.
b) Pump the Jet of Steam Button several times before
mE d
Close the Water Fill Cover.
using for the first at each ironing session.
seconds interval
Re-install the Water Tank to the main unit, untill a click sound is heard.
c) The interval should not less than 2-5 seconds
关 o 个
when using the Jet of Steam, to avoid the hot
|
|
water dripped from the Soleplate.
a
i
i9
RT.
When using Vertical Steam, hang the garment on
Move to Dry( 关 ) position
:
l-—--—
=
i
ONZ
os
/
f
a clothes hanger. Hold the iron away from your
Weusnte
ef
清水
SS
e
y
body close to but not touching the fabric.
Can use vertically
Button.
GML
AJA
gm
Me
|
Pull the fabric tight with your free hand and after
Ə NA
qo
jki
a
i
2-5 seconds press the Jet of Steam Button.
i
ld
Notice:
O
Plug the AC Power Cord into electrical outlet, connect to power supply.
@ When using Jet of Steam, keep the Steam/Dry
Set the iron on the Power Base securely.
Push the Temperature Selected Button until the red light for steam zone starts blinking.
Notice:
some water will drop from iron.
(D Do not leave the iron unattended while it is connected to the electrical source.
(9 Never iron clothes on the body or point your iron
@) When use Regular Steam or Jet of Steam, please set the Temperature Selected
at anyone when steaming.
Button to "E" zone. Low temperature will lead to water leakage.
Notice:
(D The Power Cord Adapter must be inserted into Power Base securely.
Q While fill Water Tank with water, don't plug the AC Power Cord
into electrical outlet.
Shake the
Selector in the Dry( 关 ) position and set the
water tank
Temperature Selected Button to "高 " zone, or
The water volume can be observed very clearly whatever in
a) Preheat the iron until the Indicator Light change
vertical or horizontal position. Please pull out the Plug when
from blink to illumination (while the iron being use,
the volume of water is low, and refill the iron according
it reheat itself when the temperature decline, the
Temperature
to the step o-o.
Mq
Select Scale
light doesn't blink.)
á
Move the Steam/D
b) Move the Steam/Dry Selector, select steam
© a) After ironing, push the Temperature Selected Button until
- Selector to the Dry( 关 )
quantity; and start to iron.
position
Notice:
(D The iron should be set on the Power Base securely for connecting to power
supply, while not in use, please set back to Power Base, the Power Base will
maintain the selected temperature. Just put the iron into Power Base,
don't put it at other place.
* This iron must be used with its Power Base.
the " OFF(IBrJF) " light turns on, pullout Plug.
b) Move the Steam/Dry Selector to the "Dry( 关 )" position,
press the Water Tank Release Button, take out the Water Tank.
c) Empty water from Water Tank.
d) Re-install Water Tank, keep the Steam/Dry Selector in the
"Dry( X)" position.
- 13 -
-14 -
Advertisement
Table of Contents
