1. Manuals
  2. Brands
  3. Sipromac Manuals
  4. Packaging equipment
  5. 650A
  6. Owner's manual

Sipromac 650A Owner's Manual

Vaccum machine
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OWNER'S MANUAL
MANUEL DE L'UTILISATEUR
VACCUM MACHINE
650A
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 650A and is the answer not in the manual?

Questions and answers

Related Manuals for Sipromac 650A

Summary of Contents for Sipromac 650A

  • Page 1 OWNER’S MANUAL MANUEL DE L’UTILISATEUR VACCUM MACHINE 650A...
  • Page 3 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your machine. Failure to comply with these instructions may result in personal injury.
  • Page 4 Service • Use proper containers when draining the oil. Do not use food or beverage containers that may mislead someone into drinking from them. Properly dispose of the containers, or store in a safe place immediately following the draining of the oil. •...
  • Page 5 VACUUM PACKAGING MACHINE MODEL 650A (MC-40 SIPROMAC) GENERAL TABLE OF CONTENTS OPERATION INSTRUCTIONS II MECHANICAL A- Front view general assembly drawing B- Rear view general assembly drawing C- Cover adjustment procedure D- Central shaft assembly drawing E- Seal bar assembly drawings...

  • Page 6: Table Of Contents

    VACUUM PACKAGING MACHINES OPERATION INSTRUCTIONS TABLE OF CONTENTS 1. Setting up the machine 2. Electrical connection 3. Operation 3.1 Working principles 3.2 Special packaging 3.2.1 Gas flushing 3.2.2 Top and bottom sealing (bi-active) 3.2.2 3.2.3 Electrical bag cut 3.3 Setting of digital controls 3.4 Daily cleaning 4.

  • Page 7: Setting Up The Machine

    SIPROMAC INC. VACUUM PACKAGING MACHINES 1. SETTING UP THE MACHINE: Before choosing the site for the machine, please consider that you will also need room for packaged and non-packaged products apart from the space needed for the machine itself. Keep in mind that the machine must not be set up upon uneven ground. Especially with mobile models, the weight of the pump might then cause warping of the machine.

  • Page 8: Special Packaging

    To obtain nice packages, the products and the bags have to be of proportional sizes. The bag's opening should never exceed 50 cm(2") past the seal bars. The product should be centered in height in relation to the seal bar by adjusting the spacers provided. To obtain a good seal, make sure that no residue of fat is left between the bag's inner sides where sealing is done.
  • Page 9 3.3 Vacuum packaging operation: 3.3 Vacuum packaging operation: Note: Refer to the menus structure on page 14 and the keyboard detail on page 15. 3.3.1 Basics: Use key "POWER" to power ON / OFF the vacuum packaging machine. When the unit is energized, the identification of the last executed program is displayed on LCD screen.
  • Page 10 3.3.3 Programs menu: 3.3.3.1 Program identification: For a selected program, set the identification, using the numeric keyboard characters chart; press numeric key untill the desired character is selected (4 times for the numeric value). Use key "ENTER" to validate the character and to validate the characters string at the end(the new characters string is blinking).
  • Page 11 15s  keys 1, 5...
  • Page 12 3.3.3.4 Gas flush level setting: For a selected program set the gas flush level following the same procedure as for the vacuum level; the maximum gas flush level setting is 10% below the vacuum setting. 3.3.3.5 Sealing time setting: For a selected program set the sealing time, starting with the seconds; the decimal point is automatically inserted following the first digit entry and the validation is automatically performed following the third digit entry (the new sealing time is blinking).
  • Page 13 "D3 MODEL SELECT" "D4 GAS OPTION" "D5 SEALING TIME" "D6 COOLING TIME" "D7 OFFSET CALIB.” "D8 VACUUM SENSOR” "D9 SIPROMAC PUB” "D10 LOADING TIME" (automatic units only) "D11 UNLOADNG TIME" (automatic units only) "SYSTEM MONITOR" (no access code required) "SOFTWARE: R x.xx"...
  • Page 14 -KEYBOARD DETAILS- MC-40 CONTROLS...

  • Page 15: Daily Cleaning

    WARNING: All electrical work described in this brochure should be done by a QUALIFIED and AUTHORIZED technician. 3.4 Daily cleaning: For hygenic cleanliness, it is imperative to clean chamber and spacers daily. Also clean the lid rubber to assure tight seat of the lid. Cleaning instructions for gas injection nozzles: Periodically on a regular basis the gas injection nozzles must be removed with the connection tube and soaked in a food grade soap and water solution, then dried and re-installed.

  • Page 16: Insufficient Vacuum

    4.2 Insufficient vacuum: 4.2.1 Leakage in the bag: Most frequently, insufficient vacuum in bags is due to leakage in bag and not due to any fault of the machine. Pin-hole leak for which there is no obvious explanation is due to faulty bag material. Pin-hole leak caused by sharp edge of the product (bone, etc.).Use bone-guard or thicker film.

  • Page 17: Faulty Seal

    4.3 Faulty seal: 4.3.1 Insufficient seal: Damaged teflon or silicone rubber. Sealing pressure too low, bellows leaking or pressure bar jammed. Leakers in seal: heating wire mechanically damaged (knicked) or silicone rubber uneven. 4.3.2 No seal: Sealing wire burnt. Faulty contact in sealing circuit. Sealing transformer burnt through.

  • Page 18: Control Board Failure

    4.5 MC40 Control board failure NOTE:Refer to menu structure on page 13. This board software is allowing access to a "Diagnostics Menu". Only qualified service technicians are authorized to access this menu by entering a security password. By acceding either the "D1 input test" feature or the "D2 output test" feature,a trained technician will be able to quickly know the origin of the problem: pump, sealing system, pneumatic problem, security switches problem, etc...
  • Page 19 MODEL 650A COVER ADJUSTMENT PROCEDURE Reference Drawing:# 005-0325 # 004-0122 PROBLEM: MACHINE TABLE AND COVER SEEMS TO BE STRAIGHT, LID GASKET IS GOOD BUT COVER DOES NOT SIT PROPERLY ON BOTH SIDES OF TABLE. 1. Floor should be flat (within 1/8" approx.).
  • Page 20 MECHANICAL DRAWING...
  • Page 21 051-0622 NUT 3/8"-16nc. NYLON LOCK S/S 051-0630 NUT 1/2"-13 S/S 051-0783 WASHER 3/8" FLAT THICK S/S 056-0125 HITCH PIN CLIPS 3mm X 60mm S/S DETAIL A MACHINE DEPT. TOL. METRIC INCH 650A SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ±...
  • Page 22 100-0463 TEE 1/4" NPT S/S 102-0361 Y BRANCH 1/4'' MNPT X 3/8'' T. QUICK 102-0410 MALE CONN.1/4"MNPTx3/8"T.QUICK 106-00701 VALVE 3WAY 24V 1/4''NPT MACHINE DEPT. TOL. METRIC INCH 650A SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ±...
  • Page 23 056-2600 SPRING PAWL LATCHE SS KNOB 051-0071 SCREW 4-40 x 1/4" RND SLOT S/S 051-0541 NUT # 4-40 NYLON LOCK SS DETAIL A MACHINE DEPT. TOL. METRIC INCH 650A SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020"...
  • Page 24 102-0551 BULKHEAD 1/4"NPT X 3/8 TUBE QUICK SILICONE ON EACH SIDE AND ON TOP SILICONE SUR CÔTÉ ET DESSUS MACHINE DEPT. TOL. METRIC INCH 650A SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ±...
  • Page 25 DESCRIPTION 004A4139 VACUUM SENSOR FILTER SUPPORT 114-2020 FILTER / DRYER ¼"mnpt. X 1/4"t.p. COMP. 102-0410 MALE CONN.1/4"MNPTx3/8"T.QUICK MACHINE DEPT. TOL. METRIC INCH VACUUM SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ± 0.020"...
  • Page 26 MC-40 DETAIL A NOTE: - 026-3161 - DISCONNECT SWITCH SHAFT: COUPER À 134 MM DE LONG. MACHINE DEPT. TOL. METRIC INCH VACUUM SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ± 0.020" ST-GERMAIN DE GRANTHAM...
  • Page 27 026-3160 HANDLE RED/YELLOW NEMA 4X, COMPACT, PADLOCKABLE 127-0100 STICKER ELEC.HAZARD ISO 2-1/2'' TRIANGLE 5 CENTER WITH HANDLE 16.4 MACHINE DEPT. TOL. METRIC INCH VACUUM SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ± 0.020" ST-GERMAIN DE GRANTHAM...
  • Page 28 056-2600 SPRING PAWL LATCHE SS KNOB 051-0071 SCREW 4-40 x 1/4" RND SLOT S/S 051-0541 NUT # 4-40 NYLON LOCK SS MACHINE DEPT. TOL. METRIC INCH VACUUM SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ±...
  • Page 29 051-0783 WASHER 3/8" FLAT THICK S/S 056-01675 KEY 1/4" SQ. x 1 1/4" ROUNDED END S/S 105-0450 METAL CABLE CLAMPS #6 SS DETAIL B DETAIL C MACHINE DEPT. TOL. METRIC INCH 650A SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ±...
  • Page 30 - INSTALL THEM LOOSELLY BY THIGHTENING THE NUT BY HAND - TENSION SPRING EQUALLY. THE STRECHTED LENGTH MINUS THE INITIAL LENGTH MUST BE THE MACHINE DEPT. TOL. METRIC INCH 650A SAME ON EACH SPRING. SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ±...
  • Page 31 AJUSTEMENT DE L'ARBRE / SHAFT ADJUSTMENT - UTILISER LES CALES POUR POSITIONNER L'ARBRE MACHINE DEPT. TOL. METRIC INCH - CENTRER L'ARBRE HORIZONTALEMENT DANS LE TROU DE LA TABLE 650A SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020"...
  • Page 32 SOUDAGE ± 0. 5 ± 0.020" ST-GERMAIN DE GRANTHAM PART QUEBEC CANADA SPRING INSERT ASSEMBLY N.T.S. DEPT. QTY. ITEM M-(M) AJOUT 420A ET 650A 14-08-04 SBU LISTE AJOUTER 620A DWG BY DATE 13-01-23 J.G. MAT. J.G. 13-01-15 004A3968 DATE LET.
  • Page 33 ± 0.020" SOUDAGE ± 0. 5 ± 0.020" ST-GERMAIN DE GRANTHAM PART QUEBEC CANADA SHACKLE ASS'Y N.T.S. DEPT. QTY. ITEM M-(M) AJOUT 420A ET 650A 14-08-04 SBU LISTE AJOUTER 620A DWG BY DATE 13-01-23 J.G. MAT. J.G. 12-11-06 004A3937 DATE LET.
  • Page 36 -ITEM #2 FLUSH WITH ITEM #4 & #5. 700A 680A -END VIEW- -BAG CUT OPTION- 650A MACHINE MACHINE DEPT. TOL. METRIC INCH SIPROMAC 650A, 680A & 700A USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ± 0.020" ST-GERMAIN DE GRANTHAM PART...
  • Page 37 DETAIL A 700A 680A -BAG CUT (ECO) - 650A MACHINE MACHINE DEPT. TOL. METRIC INCH SIPROMAC 650A , 680A & 700A USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ± 0.020" ST-GERMAIN DE GRANTHAM...
  • Page 38 700A -END VIEW- 680A -TOP & BOTTOM SEALING OPTION- 650A MACHINE MACHINE DEPT. TOL. METRIC INCH SIPROMAC 650A, 680A & 700A USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ± 0.020" ST-GERMAIN DE GRANTHAM...
  • Page 39 650A SEALING OPTION 580A MACHINE MACHINE DEPT. TOL. METRIC INCH SIPROMAC 580A, 650A, 680A & 700A USINAGE ± 0.1 ± 0.004" INSTALLER CONTRE L'ENCOCHE DE L'ITEM #2 11 INSTALL AGAINST NOTCH OF ITEM #2 TOLERIE ± 0.5 ± 0.020" SOUDAGE ±...
  • Page 40 13 INSTALL AGAINST NOTCH OF ITEM #4 PERMETTRE DE BOUGER LIBREMENT ALLOW TO MOVE FREELY -TOP & BOTTOM SEALING OPTION- MACHINE DEPT. TOL. METRIC INCH SIPROMAC 580A, 650A, 680A & 700A USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ±...
  • Page 42 INSTALLER TROU DE CE CÔTÉ DU RÉSERVOIR D'HUILE 165M³ BUSCH PUMP INSTALL THIS HOLE ON THE OIL RESERVOIR SIDE MACHINE DEPT. TOL. METRIC INCH 650A SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ±...
  • Page 43 106-0067 VALVE 2WAY 24V 2'' NPT(B80) 60HZ 114-2030 VACUUM MUFFLER 1-1/4"NPT DETAIL A -OPTION - 165M³, 255M³ & 305M³ PUMP MACHINE DEPT. TOL. METRIC INCH VACUUM SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ±...
  • Page 44 100-0555 RED.BUSH.1-1/2" x 1-1/4" NPT S/S 100-0558 RED. BUSHING 2"mnpt. X 1"fnpt S/S DETAIL A -OPTION - 165M³, 255M³ & 305M³ PUMP MACHINE DEPT. TOL. METRIC INCH VACUUM SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ±...
  • Page 45 100-1250 STRAIGHT 2"MNPT X 2" HOSE BARB SS 10 11 12 13 SMALL HOLES MUST BE ON OIL RESERVOIR SIDE -OPTION - 255M³ & 305M³ PUMP MACHINE DEPT. TOL. METRIC INCH 650A SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ±...
  • Page 46 102-0361 Y BRANCH 1/4'' MNPT X 3/8'' T. QUICK -OPTION - GAS DOUBLE CHAMBER SINGLE CHAMBER MACHINE MACHINE DEPT. TOL. METRIC INCH VACUUM SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ± 0.020"...
  • Page 47 102-0361 Y BRANCH 1/4'' MNPT X 3/8'' T. QUICK 106-00701 VALVE 3WAY 24V 1/4''NPT TO OTHER VALVE FROM PUMP -OPTION - AIR REGULATOR MACHINE DEPT. TOL. METRIC INCH VACUUM SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ± 0.020"...
  • Page 48 TO BELLOWS AIR PRESSURE INLET VACUUM FROM OTHER VALVE -OPTION - AIR REGULATOR MACHINE DEPT. TOL. METRIC INCH 600A & 620A SIPROMAC USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ± 0.020" ST-GERMAIN DE GRANTHAM...
  • Page 50 USE PERMATEX RUBBER ADHESIVE 169-0013 TO GLUE UTILISER PERMATEX RUBBER ADHESIVE 169-0013 POUR COLLER 87.5 TENIR SECTION A-A MACHINE DEPT. TOL. METRIC INCH SIPROMAC 650A & 680A USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ±...
  • Page 51 USE PERMATEX RUBBER ADHESIVE 169-0013 TO GLUE UTILISER PERMATEX RUBBER ADHESIVE 169-0013 POUR COLLER 87.5 TENIR SECTION A-A MACHINE DEPT. TOL. METRIC INCH SIPROMAC 650A & 680A USINAGE ± 0.1 ± 0.004" TOLERIE ± 0.5 ± 0.020" SOUDAGE ± 0. 5 ±...

Table of Contents