Related Manuals for MSA G1-H
Summary of Contents for MSA G1-H
- Page 1 Operating Manual G1-H Mask - Positive Pressure Mask/Helmet Combination G1-H/F1 Order No.:D2058100/08 MSAsafety.com...
- Page 2 The Declaration of Conformity can be found under the following link: https://MSAsafety.com/DoC. MSA is a registered trademark of MSA Technology, LLC in the US, Europe and other Countries. For all other trademarks visit https://us.msasafety.com/Trademarks. MSA Europe GmbH Schlüsselstrasse 12 8645 Rapperswil-Jona...
-
Page 3: Table Of Contents
Removing the Mask Spectacle Kit Cleaning, Disinfection Cleaning/Disinfection of the Filter Adapter Cleaning/Disinfection of the Helmet Cleaning, Disinfection Preparing the Mask for Cleaning or Disinfection Suitable Cleaning and Disinfection Procedures Maintenance Maintenance Instructions Maintenance Intervals G1-H Mask - Positive Pressure... - Page 4 Applicable Helmets MSA F1 Helmets Ordering Information Exploded View Accessories ATO Code 9.3.1 Europe Helmet Mask PC (Standard lens "P") 9.3.2 Europe Helmet Mask PC (Anti-scratch lens "H") 9.3.3 Europe Helmet Mask APEC (Anti-fog lens "A") G1-H Mask - Positive Pressure...
-
Page 5: Safety Regulations
1 Safety Regulations Safety Regulations Correct Use The G1-H Mask - Positive Pressure - hereafter called mask - is a respiratory interface with positive connection including head protection. They are not complete respiratory protective devices by themselves, but serve as facepieces [DIN 58610:2014] for use with compressed air breathing apparatus of the G1 series and respiratory filters. -
Page 6: Liability Information
1 Safety Regulations Liability Information MSA accepts no liability in cases where the product has been used inappropriately or not as intended. The selection and use of the product are the exclusive responsibility of the individual operator. Product liability claims, warranties also as guarantees made by MSA with respect to the product are voided if it is not used, serviced, or maintained in accordance with the instructions in this manual. -
Page 7: Description
The mask is available with different head harnesses and different component housings. Figure 1 Overview mask/helmet combination Faceblank Inlet valve Helmet adapter, right Component housing Helmet adapter, left Rubber neck strap Lens Nomex (textile) neck strap Nosecup G1-H Mask - Positive Pressure... -
Page 8: Mask Versions
EN 148-1 can be attached to the mask. The instructions for use of the respiratory filters have to be regarded, including any information regarding the use in potentially explosive atmospheres. G1-H Mask - Positive Pressure... -
Page 9: Marking
Harmonized/designated standard CE-marking with notified body number (DEKRA, Zertifizierungsstelle Dinnendahlstr. 9, 44809 Bochum) UKCA-marking with approved body number (BSI Assurance UK Ltd, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes, MK5 8PP, United Kingdom) Part number/ATO code G1-H Mask - Positive Pressure... -
Page 10: Certification
Knowlhill, Milton Keynes, MK5 8PP, United Kingdom The Declaration of Conformity can be found under the following link: https://MSAsafety.com/DoC. ATEX Categories The lowest ATEX class of a part sets the limit for the complete device. G1-H Mask - Positive Pressure I M1 Rubber II 1G IIC... -
Page 11: Cbrn
2 Description G1-H Mask - Positive Pressure II 1D I M1 II 1G IIB Textile HMC II 1D I M1 Filter Adapter for Fixed Push-to-Connect II 1G IIC II 1D Push-To-Connect I M1 Connector pieces M45x3 II 1G IIC II 1D... - Page 12 ATO configuration K-(S/1 or M/1 or L/1)-(S or M or L)-(4 or E)-(O or C or R)-(P or M or E or U or V or W), see chapter 9.3 The Operating Manual M1 Modular SCBA System must be observed. G1-H Mask - Positive Pressure...
-
Page 13: Use
Adjust the helmet according to the helmet’s operating manual. Grip the helmet with both hands with the chinstrap open. Pull the helmet from the forehead over the head. Close and slightly tighten the chin strap. G1-H Mask - Positive Pressure... -
Page 14: Donning The Mask
Donning the Mask WARNING! In order to guarantee a proper fit for those wearing glasses, the G1-H Mask - Positive Pressure spectacle kit must be worn since ordinary glasses cannot be worn under the mask. Failure to follow this warning can result in serious personal injury or death. -
Page 15: Leak Check
Remove the mask to the front. Open chin strap and remove the helmet. NOTE: Do not re-tighten the screws! Moving of Helm Flex adapters/brackets is normal after use. G1-H Mask - Positive Pressure... -
Page 16: Spectacle Kit
Push the top part of the frame into the lens. The faceblank has three rubber tabs to grab the frame. Place the frame in the middle of the lens with the smaller tabs grabbing the wire frame. G1-H Mask - Positive Pressure... - Page 17 Repeat step (3) on the opposite side. The frame for the spectacles can be adjusted up/down and in/out depending on the facial features. Don the mask and adjust to optimize visibility. G1-H Mask - Positive Pressure...
-
Page 18: Cleaning, Disinfection
For online version scan the QR code or go to the product page on www.MSAsafety.com. The power supply for the HUD (if applicable) is not part of the G1-H Mask - Positive Pressure and is therefore not damaged during cleaning. -
Page 19: Suitable Cleaning And Disinfection Procedures
(Marking P) (Marking A) (Marking H) Cleaning/Disinfection by hand Machine Cleaning/Disinfection Lens Identification Figure 7 Marking Marking placement Mask with Standard Lens (Marking P) Mask with Anti-Fog Lens (Marking A) Mask with Anti-Scratch Lens (Marking H) G1-H Mask - Positive Pressure... -
Page 20: Maintenance
This product should be regularly checked and serviced by trained specialists. Inspection and service records must be maintained. Always use original parts from MSA. Repairs and maintenance must be carried out only by authorized service centres or by MSA. Changes to devices or components are not permitted and will result in loss of approval. -
Page 21: Component Housing Cover
Push-to-Connect AS/M45x3/ESA Insert the delatching tool (10204283-SP) into the tabbed slot with below the connector. Leverage the tool down to unlock until it unsnaps. Rotate the cover off of the facepiece. G1-H Mask - Positive Pressure... -
Page 22: Installing The Component Housing Cover
Press the cover over the front of the component housing assembly until the locking tab snaps into place with an audible click. NOTE: Apply even pressure on both sides of the cover to snap the locking tab securely onto the component housing assembly. G1-H Mask - Positive Pressure... -
Page 23: Maintenance Of The Exhalation Valve
Remove the exhalation valve. Discard if the valve is torn, tacky, or otherwise damaged. NOTE: Be careful not to damage the fork seats or valve seat. If either is damaged, replace the component housing. G1-H Mask - Positive Pressure... -
Page 24: Installing The Spring Retainer And Exhalation Valve
NOTE: Ensure the valve stem is inserted into the center slot. Fit the spring over the ring of the exhalation valve. Align the forks on the flat surface of the component housing and slide forward until each fork snaps into place. G1-H Mask - Positive Pressure... -
Page 25: Replacing The Speech Diaphragm
Perform a tightness test (→ Tightness Test of the Mask The testing of the masks for tightness is performed using an applicable MSA test device (i. e. SmartCHECK) in accordance with the relevant operating manual. Fit mask tight onto the test device. -
Page 26: Helmet Maintenance
6 Maintenance Helmet Maintenance For detailed information about helmet maintenance refer to the helmet operating manual. G1-H Mask - Positive Pressure... -
Page 27: Safekeeping And Storage
Failure to follow this warning can result in serious personal injury or death. For the safekeeping of the mask the mask container should be used. MSA rubber products are protected by an anti-aging agent that can become visible as a light coating. This coating is harmless and can be removed during cleaning. -
Page 28: Applicable Helmets
Ex ia IIIC T135 °C .. T200 °C Db • Flexible microphone II 2G Ex ib IIC T4 Gb headset Communication If the colors of the connector are Accessories • Bone conductive headset identical, the corresponding combination is ATEX compliant. • Headset G1-H Mask - Positive Pressure... - Page 29 Yellow, orange, silver Ex I M1, Ex II 1D, Ex II 1G IIC Helmets F1E No use of mask-helmet combinations with F1E in potentially explosive atmospheres yellow blue Color of the shell black grey green fluorescent orange G1-H Mask - Positive Pressure...
- Page 30 No use of mask-helmet combinations with F1E in potentially explosive atmospheres fluorescent yellow photoluminescent white with black comb with or without ocular visor (GA1046A) Gold version (GA1055C) Face shield Clear version (GA1055B) Aluminized (GA 1106R) Neck curtain Wool/Nomex black (GA1106P) G1-H Mask - Positive Pressure...
-
Page 31: Ordering Information
9 Ordering Information Ordering Information Exploded View Figure 8 G1-H Mask - Positive Pressure G1-H Mask - Positive Pressure... -
Page 32: Accessories
Lens, PC coated, G1 Facepiece, Lens, PC-HC 3mm, G1 Facepiece, Spare 10176797-SP Lens, APEC, G1 Facepiece, Lens, G1 Facepiece 10144194-SP Lens ring, upper 10144195-SP Lens ring, lower 10144196-SP Cover, Component housing, Fixed Push-To-Connect G1 10144187-SP Cover, Component housing, Push-To-Connect (AutoMaXX) 10144190-SP G1-H Mask - Positive Pressure... - Page 33 10144230 Filter Adapter Assy, G1 Facepiece 10144231 Speaking diaphragm retaining tool 10149560 Upgrade kit G1 ESA/M45X3 C1 prepared 10194309 Upgrade kit G1 MAXX, C1 prepared 10194308 Delatching Tool, Cover, G1 FP EU (PKG 5) 10204283-SP G1-H Mask - Positive Pressure...
-
Page 34: Ato Code
For this product, order numbers have been replaced by an ATO (Assemble To Order) code. To order a G1-H Mask - Positive Pressurewith a medium sized faceblank, a medium nosecup, rubber neck strap and Push-To-Connect connector piece, the ATO code would be... -
Page 35: Europe Helmet Mask Pc (Anti-Scratch Lens "H")
E - ESA ("M"+ ESA-Adapter) L/I - Large Hycar S - Small 0 - None 2 - Fixed Push-To-Connect H - Helmet Mask Adapter L/2 - Large R - Rubber P - Push to Connect Sensitive Medium G1-H Mask - Positive Pressure... -
Page 36: Europe Helmet Mask Apec (Anti-Fog Lens "A")
L/2 - Large H - Helmet R - Rubber P - Push to Connect Sensitive Medium Mask Adapter M - M45 x 3 H - Cloth L - Large (MHC) E - ESA ("M"+ ESA-Adapter) G1-H Mask - Positive Pressure... - Page 37 9 Ordering Information G1-H Mask - Positive Pressure...
- Page 38 For local MSA contacts, please visit us at MSAsafety.com...