Table of Contents
Advertisement
Troubleshooting
Malfunctions often have simple explanations. Refer to the table
before calling the after-sales service as you may be able to
remedy the fault yourself.
Malfunction table
If a dish does not turn out exactly as you wanted, refer to the
Tested for you in our cooking studio section, where you will
find plenty of cooking tips and tricks.
Problem
The appliance does not work.
The text "Set clock" appears in the
display. The time is not the current time.
The oven door cannot be opened. The text
"Set clock" appears in the display. The
time displayed is not the current time.
The oven does not heat up or the type of
heating selected cannot be set.
The oven does not heat up. The text
"Demo" is displayed.
"Automatic switch-off" appears in the
display.
Error messages with E
If an error message with E is shown in the display, press the
button. This cancels the error message. You may then have
0
Error message
E011
E115
Replacing the bulb in the oven ceiling light
If the bulb in the oven light fails, it must be replaced. Heat-
resistant, 25 watt, 230 V halogen bulbs are available from the
after-sales service or specialist retailers. When handling the
halogen bulb, use a dry cloth. This will increase the service life
of the bulb. Only use these bulbs.
ã=
Risk of electric shock!
Switch off the circuit breaker in the fuse box.
Place a tea towel in the oven when it is cold to prevent
1.
damage.
Remove the glass cover. To do this, press the metal tabs to
2.
the side with your thumb (Fig. A).
Pull out the bulb (do not turn it ) (Fig. B). Insert the new bulb,
3.
making sure that the pins are in the correct position. Push the
bulb in firmly.
ã=
Incorrect repairs are dangerous. Repairs may only be carried
out by one of our trained after-sales engineers.
Possible cause
Defective fuse
Power cut
Power cut during self-cleaning.
Type of heating not recognised
The oven is in demo mode.
Automatic switch-off has been
activated. The oven switches off.
to reset the time. If the error is shown again, call the after-sales
service.
You can take remedial action yourself if the following error
messages are displayed.
Possible cause
A button was pressed for too long
or has jammed.
The temperature in the cooking
compartment is too high.
$
4.
5.
Replacing the bulb in the left-hand oven light
If the bulb in the oven light fails, it must be replaced. Heat-
resistant, 25 watt, 230 V halogen bulbs are available from the
after-sales service or specialist retailers. When handling the
halogen bulb, use a dry cloth. This will increase the service life
of the bulb. Only use these bulbs.
Risk of electric shock!
Note/remedy
Look in the fuse box and check that the circuit
breaker is in working order.
Turn the rotary selector to set the current time then
press the
button.
0
Turn the rotary selector to set the current time then
press the
0
button. Wait until the cooking
compartment has cooled down. The
disappears. You can now open the oven door.
Make the settings again.
Switch off the circuit breaker in the fuse box and
then switch back on after approx. 20 seconds. In
the next 2 minutes hold the
four seconds until the text "Demo" disappears.
Press any button. The text disappears. You can
make settings again.
Note/remedy
Press all buttons individually. Check that the
buttons are clean. If the error message remains,
please contact the after-sales service.
The oven door locks. Wait until the cooking
compartment has cooled down. Clear the error
message with the
Refit the glass cover. When doing this, insert it on one side
and press firmly on the other side. The glass cover will click
into place.
Remove the tea towel and switch on the circuit breaker.
symbol
H
button down for
D
button.
0
%
19
Advertisement
Table of Contents
