Download Print this page

Pulsar EXPANDER 1 Assembly Instructions

Advertisement

Quick Links

1. Przeznaczenie:
Obudowa AWO452 zaprojektowana została jako element systemów SSWiN, KD, itp.
Przeznaczona jest do montażu (w zależności od modelu):
ekspanderów (modułów) wejść/wyjść itp.
nadajnika, modułu GSM,
innych dedykowanych urządzeń
2. Montaż:
Obudowa przeznaczona jest do montażu przez wykwalifikowanego instalatora, posiadającego odpowiednie
( wymagane i konieczne dla danego kraju) zezwolenia i uprawnienia do ingerencji w instalacje niskonapięciowe.
Obudowa (+PCB) powinna być montowana w pomieszczeniach zamkniętych, o normalnej wilgotności powietrza
(RH=90% maks. bez kondensacji) i temperaturze z zakresu -10°C do +40°C.
Urządzenia elektroniczne zawierają elementy elektroniczne wrażliwe na wyładowania
elektrostatyczne. Przed montażem należy rozładować ładunki elektrostatyczne,
1. Zamontować obudowę w dedykowanym miejscu i doprowadzić przewody połączeniowe i sygnałowe poprzez przepusty
kablowe.
2. Zamontować w obudowie urządzenie w odpowiednich otworach montażowych ( z użyciem: kołków dystansowych,
wkrętów montażowych itp.).
3. Wykonać połączenia wymagane dla danego typu urządzenia/systemu.
Uwagi: zgodnie z wymaganiami i zaleceniami producenta.
4. Wykonać uruchomienie, regulacje lub konfiguracje: zgodnie z procedurą producenta systemu.
5. Po instalacji i uruchomieniu systemu należy zamknąć obudowę.
1. Destination:
The AWO 452 metal casings are designed as components in intruders alarms, access control systems, security
systems etc. There are intended for installation:
expander modules
GSM transmiter, ISDN module
other to dedicated devices, components etc.
2. Installation:
The metal casing must be installed by a qualified installer, holding the relevant certificates, required and
necessary in the particular country for connecting (interfering with) low-voltage installations.
The casing should be installed indoors, where air humidity is normal (RH=90% max. without condensation) and
temperature in the range of -10°C do +40°C.
Caution!
electric charges. Prior to installation, these charges must be removed. During
1. Install metal casing in dedicated place and bring in the connecting and signal conductors through cables bushings.
2. Mount the device with dedicated holes (use: distance pins, bracket screw).
3. Make other connections required for the correct type of system / device.
Remarks: consistent with requirements and recommendation of the producer.
4. Start the system, adjust or configure: according to procedure of the producer's system.
5. After installing and checking the proper operation of the system, close the casing.
INSTRUKCJA MONTAŻU/ASSEMBLY INSTRUCTIONS
Obudowa metalowa do: ekspanderów, modułów GSM/ISDN itp.
Metal casings for: expanders, GSM/ISDN module, etc.
a w czasie montażu unikać dotykania elementów na płycie.
Electronic devices contains electronic components sensitive to
installation, avoid touching any elements on the board.
POLSKI/ENGLISH
Kod / Code: AWO 452
Nazwa/ Name: EXPANDER 1
Zastępuje wydanie: -----------------------
IM452
Wydanie: 1 z dnia 12.01.2012
PL
EN

Advertisement

loading
Need help?

Need help?

Do you have a question about the EXPANDER 1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Pulsar EXPANDER 1

  • Page 1 INSTRUKCJA MONTAŻU/ASSEMBLY INSTRUCTIONS POLSKI/ENGLISH Kod / Code: AWO 452 Nazwa/ Name: EXPANDER 1 Obudowa metalowa do: ekspanderów, modułów GSM/ISDN itp. Metal casings for: expanders, GSM/ISDN module, etc. IM452 Wydanie: 1 z dnia 12.01.2012 Zastępuje wydanie: ----------------------- 1. Przeznaczenie: Obudowa AWO452 zaprojektowana została jako element systemów SSWiN, KD, itp.
  • Page 2 PL/EN 3. Parametry techniczne / Technical data: PARAMETRY TECHNICZNE / TECHNICAL DATA 1x – otwarcie obudowy Zabezpieczenie antysabotażowe Tamper protection 1x – opening casing Obciążalność wyjścia TAMPER- max Output current TAMPER - max 500mA@50Vdc Obudowa: IP Casing: IP IP 20 Temperatura pracy Operating temperature -10ºC÷40ºC...
  • Page 3 GENERAL WARRANTY CONDITIONS 1. Pulsar K. Bogusz Sp.j. (manufacturer) grants a two-year quality warranty for the equipment, starting from the date of purchase placed on the purchase order.

This manual is also suitable for:

Awo452