ControlByWeb X-412 Quick Start Manual

Hide thumbs

WebSwitch

WebSwitch Plus

WebRelay

WebRelay-Quad

WebRelay Wireless

WebRelay-10 Plus

WebRelay-10

| Quick-Start Guide

FridgeAlert

X-432

X-404C

X-412C

FridgeAlert Cellular

X-DTHS-P

X-317

X-332

X-400

X-404

X-405

X-406

X-408

X-TC1W-K

X-DTHS-WMX

X-310

X-DTHS-WMX

X-300

X-TC1W-K

X-301

X-400C

X-310

X-422

X-410C

X-412

XW-112

X-422

X-600M

X-430

X-410

XW-110 Plus

XW-110

X-417

XW-111

X-418

X-420

X-401

Basic Setup Steps (with DHCP)

1. Disconnect any Ethernet cables and/or network connections from your

1. Connect the module to power (Two AA batteries or 5VDC).

Cloud Setup & Cell Activation

Basic Setup Steps

Installation Steps

Installation Instructions

Installation Steps

Basic Setup Steps

Installation Steps

Basic Setup Steps

(For faster setup, we recommend doing this step first)

computer.

(For faster setup, we recommend doing this step first)

2. On a computer, scan for open Wi-Fi networks & connect to the SSID:

1. Connect X-600M to local network using an Ethernet Cable.

1. Register or login to your account at: www.ControlByWeb.cloud

1. Power the module and connect to network.

1. Power the module and tap the "Network Setup" tab on the

1. Power the module and connect to network.

Mounting Clip Installation - Slide the mounting clip onto the

Wiring - Before mounting the enclosure to the wall, remove

Installation - Install the X-TC1W-K in a protected location

2. Attach the included antenna to the module and connect the WebRelay

Wiring

Mounting Clip Installation

XW110P-[Last six digits of Serial Number]

XW110-[Last six digits of Serial Number]

XW111-[Last six digits of Serial Number]

XW112-[Last six digits of Serial Number]

Install the X-TC1W-K

2. AFTER the network is connected, apply power.

2. Choose 'Devices' from the left navigation bar and click 'New Device'.

2. Set IP address on computer to be on the same network as

the cover from the enclosure. Thread the appropriate wire

away from rain and direct sunlight. The internal cold junction

body of the sensor. Insert two screws through the mounting

right of the touch screen. (Tap the screen if it's not visible)

Wireless module to power. The Link light will flash. If not, press the

3. If no Wi-Fi network is found called XW112-[Last six digits of

3. If no Wi-Fi network is found called XW111-[Last six digits of

3. If no Wi-Fi network is found called XW110-[Last six digits of

3. If no Wi-Fi network is found called XW110P-[Last six digits of

Slide the mounting clip onto the body of the sensor. Insert two screws

Before mounting the enclosure to the

Install the X-TC1W-K in a protected

3. Wait about 10 seconds and enter into the address bar of your

3. On the New Device page, select the 'Cell Device' tab.

'Access Point' button on the module for 2 seconds.

2. Tap either Ethernet Settings or Wireless Settings.

through the opening in the back, and connect each wire lead

holes and into the surface you are mounting against.

compensation will be more accurate if the X-TC1W-K is

the module. (Example: Set computer to 192.168.1.50)

through the mounting holes and into the surface you are mounting

wall, remove the cover from the

location away from rain and direct

Serial Number], remove the front cover and press the 'Access

4. Enter a device name, the last 6 digits of serial number, and the Cell ID

3. Using a computer/mobile device, scan for Wi-Fi networks and connect

browser:

enclosure. Thread the appropriate

against.

sunlight. The internal cold junction

3. To configure the module, open a web browser and enter:

protected from rapid temperature changes.

(Data, Gnd, and +5V In).

• Ethernet - Enable DHCP.

Point' button for 2 seconds.

(located on the side of the device) and click 'Submit'.

wire through the opening in the back,

to SSID: WebRelay Wireless-[Last six digits of Serial Number]

compensation will be more accurate

http://x600.local/setup.html

Thru-Wall Mounting Bracket Installation - Drill a 5/8" hole

http://192.168.1.2/setup.html

• Wireless - Enable Wireless. Select your network and

http://192.168.1.2/setup.html

4. Once connected, open a web browser and enter:

and connect each wire lead (Data,

5. You'll be redirected to the Device Edit page. *Click 'Activate SIM Card'.

Thru-Wall Mounting Bracket Installation

if the X-TC1W-K is protected from

5. You'll be redirected to the Device Edit page. *Click 'Activate SIM Card'.

4. Once connected, open a web browser and enter:

4. Enter the username (admin) and password (webrelay).

through the wall, duct, etc. that you would like to monitor, and

Wall Mounting - With the enclosure cover still open, mount

Gnd, and +5V In).

Thermocouple Sensor - Connect the thermocouple sensor

http://192.168.1.2/setup.html

rapid temperature changes.

4. Assign permanent IP address to module, then restart module.

Assign permanent IP address to module, then restart module.

security. Enter the password, then enable DHCP.

http://192.168.1.2/setup.html

6. Once activated, power up the X-404C.

*Note: If data plan was

Drill a 5/8" hole through the wall, duct, etc. that you would like to

5. Click on the Network setup pages and change the IP

the enclosure to the wall with two small screws in the provided

secure the mounting bracket with two screws.

into the positive (+) and Negative (-) terminals.

5. Enter local Wi-Fi network settings and power cycle the module.

May take up to 5 minutes to connect.

5. Enter local Wi-Fi network settings and reboot the module.

purchased separately, first

5. Restore computer's IP address, if necessary, and access the

monitor, and secure the mounting bracket with two screws.

Assign the module a static IP address. (Disable DHCP to

Wall Mounting

Thermocouple Sensor

address to the desired setting.

enter Data Plan Code

screw holes in the enclosure. Once mounted, re-attach the

(You can also establish communications using WPS. See users manual.)

module at its new IP address to finish setup.

see the blue "IP" box and network information) Tap a box to

module at its new IP address to finish setup.

+5V

With the enclosure cover still open,

Insert the temperature probe into the

Power

Insert the temperature probe into the mounting clip, and tighten

(sent via email) & click

Connect the thermocouple sensor into

6. WebRelay Wireless will now attempt to connect to the specified Wi-Fi

6. The module will now attempt to connect to the specified Wi-Fi network.

1-Wire Connections - The adapter has three wires which are

Basic Setup Steps (without DHCP)

enclosure cover.

Supply

mount the enclosure to the wall

mounting bracket collar with existing screw.

expand it, then enter the desired network information.

the positve (+) and negative (-) terminals.

'Apply Data Plan'.

Factory Default Settings

mounting clip and tighten mounting

network. See Link LED chart (on back) for connection status.

7. Reconnect computer to Wi-Fi network and access the module through

with two small screws in the

connected to a compatible ControlByWeb device. The cable

1. Power the module and connect to network.

Activation may take 15

3. Tap the "Back" button, then tap Reboot.

7. Reconnect computer to Wi-Fi network and access the module through

provided screw holes in the

bracket collar with existing screw.

Wiring

IP Address: 192.168.1.2

the Wi-Fi network to finish setup.

minutes. Click 'Check SIM

can be extended with additional wire, if needed.

1-Wire Connections

2. Set IP address on computer to be on the same network as

the Wi-Fi network to finish setup.

enclosure. Once mounted,

4. Tap the "Info" tab to see the IP address.

Status' to verify activation.

Subnet Mask: 255.255.255.0

Factory Default Settings

Subnet Mask: 255.255.255.0

For proper wiring, follow the illustrated diagram:

Factory Default Settings

re-attach the enclosure cover.

the module. (Example: Set computer to 192.168.1.50)

The adapter has three wires which are

Factory Default Settings

6. Once activated, power

Wiring - For proper wiring, follow the diagram below:

Control Page Web Address: http://192.168.1.2

Factory Default Settings

SSID: XW110-[Last six digits of Serial Number]

SSID: XW111-[Last six digits of Serial Number]

SSID: XW112-[Last six digits of Serial Number]

SSID: XW110P-[Last six digits of Serial Number]

Control Page Web Address: http://192.168.1.2

connected to a compatible ControlBy-

6. Once activated, power

3. To configure the module, open a web browser and enter:

up the FridgeAlert.

SSID: WebRelay Wireless-[Last six digits of Serial Number]

Control Password: (no password set)

Control Page Web Address: http://192.168.1.2

Web device. The cable can be extended

Control Page Web Address: http://192.168.1.2

up the X-410C.

up the X-412C.

up the X-400C.

Control Page Web Address: http://192.168.1.2

May take up to 5

Control Password: (no password set)

Control Page Web Address: http://192.168.1.2

http://192.168.1.2/setup.html