Download Print this page

Xantech RMGATE Installation Instructions

Rack mount adapter for the gatekeep-ir

Advertisement

Quick Links

RACK MOUNT ADAPTER FOR THE GATEKEEP-IR
SOURCE
SAT 1
SAT 2
VCR 1
VCR 2
AUX
DVD 1
AUX 1
DVD 2
TUNER 1
TUNER 2
Fig. 1 The RMGATE, Front View
The RMGATE provides a convenient means for mounting the GATEKEEP-IR™ GMB9 assembly into a
standard 19 inch rack. It incorporates eight STATUS LED's that indicate a components ON/OFF condition.
The black anodized panel is a standard 7.00 inch increment height and is 3/16" thick. Install the panel as
follows:
1. Mount the GMB9 to the rear of the RMGATE. Refer to Fig. 2 below. Use the hardware that comes
with the GMB9 and the RMGATE.
2. Plug the 3.5-to-3.5mm Mono Mini Plug cables (supplied) between the STATUS jack of each gate
module to the corresponding STATUS GATE IN jack on the RMGATE as shown (Fig. 2). That is,
connect Gate 1 (slot #1) to GATE IN 1, Gate 2 (slot #2) to GATE IN 2, etc. Use the longer 18" cables
for the 4 gates to the left and the 12" cables for the remainder.
RMGATE RACK MOUNT ADAPTER (rear view)
(not included)
Mount the GMB9 Gatekeep-IR assembly to the 4 studs on the rear of the
RMGATE using hardware included with the GMB9 and the RMGATE.
Fig. 2 A GMB9 Gatekeep-IR™ Assembly Mounted to the Rear Surface of the RMGATE Rack Panel

INSTALLATION INSTRUCTIONS

RMGATE
GMB9
Gate 1
Gate 2
Gate 3
Gate 4
(Slot #1)
(Slot #2)
(Slot #3)
(Slot #4)
GMM1A
GCM1
GEM1
GAM1
+
L
IR IN
IN
CURRENT
SENSOR
CONTROL
IN
R
IR OUT
AUDIO
L
CONFIRM
THRESHOLD
OUT
R
POWER
+12V
G
STATUS
STATUS
STATUS
C I
IR IN
ON
ON
ON
12 VDC
IR OUT
IR OUT
IR OUT
3.5-to-3.5mm Mono
Mini Plug cables (8 included)
Unused
Gate 5
Gate 6
(Slot #5)
(Slot #6)
Slots
GVM1
GTM1
GLM1
VIDEO IN
LIGHT
TEMPERATURE
SENSOR
SENSOR
VIDEO OUT
THRESHOLD
THRESHOLD
STATUS
STATUS
STATUS
ON
ON
ON
IR OUT
IR OUT
IR OUT
2.1-to-2.1mm Power
To 120 V AC
Supply cable (included).
(unswitched)
GATEKEEP-IR
LED and STATUS
pass-thru' assembly
(included on RMGATE)
STATUS
GATE
GATE
IN
OUT
1
1
2
2
3
3
0 - 12Volt
4
4
STATUS pass-thru'
for indicators, for
5
5
control of other
6
6
equipment, etc.,
as needed.
7
7
8
8
OUT
IN
POWER
782-00 Power Supply
(not included)
1

Advertisement

loading

Summary of Contents for Xantech RMGATE

  • Page 1: Installation Instructions

    The black anodized panel is a standard 7.00 inch increment height and is 3/16" thick. Install the panel as follows: 1. Mount the GMB9 to the rear of the RMGATE. Refer to Fig. 2 below. Use the hardware that comes with the GMB9 and the RMGATE.
  • Page 2 VCR 2 LED's DVD 1 AUX 1 DVD 2 TUNER 1 TUNER 2 Fig. 3 Applying the Icon Labels to the front of the RMGATE Rack Panel Custom labels for RMGATE PRE AMP SRND TUNER 2 PROJ TAPE VCR 1...