Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PRO SHOT L1-AS
Summary of Contents for PRO SHOT L1-AS
- Page 1 PRO SHOT PRO SHOT L1-AS L1-AS Operations Guide...
-
Page 2: Table Of Contents
Pro Shot laser model L1-AS is a rugged, reliable, high quality product, backed by the industry leading Guardian 36 month warranty. Warranty details are printed in the back of this manual. -
Page 3: Battery Installation
Battery Installation Battery installation Install batteries as shown here. For reference, there is a diagram label on the bracket between the batteries. Note: Batteries are shipped in the carrying case and must be installed for the laser to operate. Use the battery pocket in the case to store a spare set of batteries in order to prevent downtime. -
Page 4: Controls And Displays
Controls and Displays Slope Alignment Sights Low Batt. Indicator Laser Power Indicator Leveling Indicators Slope Display Power Switch Slope Adjustment Knob... - Page 5 Controls And Displays Slope alignment sights These sights are used to align the slope axis of the laser for excavating and grading when there is a slope required. Low battery indicator The yellow L.E.D. indicates the batteries need to be replaced. Laser Power indicator The green L.E.D.
-
Page 6: Safety
• Turn the laser off when it is not being used, such as during lunch hour, at the end of the day, or during other long breaks in the work. CAUTION CAUTION LASER LIGHT L1-AS DO NOT STARE (North America) INTO BEAM 635nm - 670nm... - Page 7 1993 IEC 825-1 laser safety standard and the revised edition of the European Norm EN60825. The L1-AS laser conforms to applicable EC directives regarding RFI and EMI. The L1-AS complies with FDA performance standards 21 CFR subchapter J.
-
Page 8: Initial Setup Guidelines
Work as close to the laser as possible. You can work up to 1000 feet from the L1-AS with the R7. As with all instruments, the farther you go, the more any error can add up. Set the laser in a safe place, as close as you can to your work Maintain your equipment. -
Page 9: Level Setup
Level Setup Follow the instructions in the "initial setup guidelines" section. Turn the laser on and allow it to level. Zero the grade display carefully. Aiming the laser when doing level work is not important. In the event that a very long distance is required, the laser can be set-up in the middle of the site, covering a total of 2000 feet (610 meters) diameter with the R7 hand held receiver or MC-1 machine control receiver. -
Page 10: Slope Setup
Slope Setup Follow the suggestions in the "initial setup guidelines" section. Carefully aim the laser using the sights on the top cap. These sights indicate the direction of slope. Using the red slope adjustment knob, adjust the slope display to your required slope. - Page 11 Slope Setup The display reads in percent of grade (the number displayed is the units of rise or fall per 100 units of run). A 2-1/2% up slope (projecting upward from the front of the laser) shows as 2.50 on the display. If a down slope is needed, the display is set to the needed slope and the rear of the laser is aimed in the direction of slope.
-
Page 12: Compound Slope Setup
Sites designed with compound slope actually have just a single resultant slope. When a site has slope in two directions, 90 degrees apart, the model S1 Compound Slope Adapter Kit can be used to calculate and set the L1-AS to the proper angle and resultant slope. - Page 13 Compound Slope Setup 3. Rotate the S1 adapter until it matches the angle determined with the slope chart. Note: if, when standing behind the laser, the highest corner on the site is to the right of the grade sight, you must rotate the adapter counter clock-wise until you reach the proper reading.
-
Page 14: Checking & Adjusting Calibration
Checking and Adjusting Calibration Calibration is your responsibility, check it often. Although the L1-AS is calibrated at the factory and is an exceptionally rugged laser, it is well worth the effort to check calibration before you first use it (after shipping) and then from time to time to ensure that you are doing the highest quality work possible. - Page 15 Checking and Adjusting Calibration 4. Take the receiver to the target and find the height of the laser beam by moving the receiver up or down until you get a display and/or tone. Now, find the center of the display and mark the target, using the receiver's beam center notch as a guide.
-
Page 16: R7 Receiver
R7 Receiver The R7 can be attached to a grade rod, Rear height display or used without the rod clamp to make reference marks on walls, floors, or other 5 channel front surfaces. The R7 senses the laser beam height display and uses a five channel front LCD to show height information. -
Page 17: Accessories
Accessories Optional Factory Accessories Extra R7 Receivers Although one R7 comes with each system, additional receivers can dramatically increase productivity on many jobs. (see picture on opposite page) Re-Chargeable Battery Kit Re-Chargeable battery includes 4 Ni-Cad batteries, a charger and a replacement battery door. Compound Slope Kit With the compound slope kit installed, the transmitter can be easily set-up to... -
Page 18: Maintenance And Troubleshooting
Maintenance And Troubleshooting Calibration • There is no set interval for calibrating the L1-AS, but calibration should be checked from time to time in order to ensure that the highest possible quality of work is being done. Calibration should always be checked if the laser has been handled roughly or shipped. -
Page 19: Guardian Warranty And Specifications
Warranty Guardian 36 month warranty coverage The L1-AS laser transmitter, along with R5 or R7 receivers, manufactured on or after February 1, 1997, are warranted for thirty-six (36) months from the date of new equipment purchase from an authorized dealer. During the warranty period,... - Page 20 LASER REFERENCE, Inc. 151 Martinvale Lane San Jose, CA 95119 • Toll Free (USA) +1.800.238.0685 Telephone +1.408.361.0220 +1.408.361.3180 www.pro proshotlaser laser.com Email sales@pro proshotlaser laser.com VERSION 2.1...