Table of Contents
Advertisement
Quick Links
COMMERCIAL
FILL OIL TANK WITH BAR AND
CHAIN OIL BEFORE FIRST USE
OPERATOR'S MANUAL
56-VOLT LITHIUM-ION
COMMERICAL POLE SAW
MODEL NUMBER PSX2510
WARNING: To reduce the risk of injury, the user must read and understand the
Operator's Manual before using this product. Save these instructions for future reference.
MNL_EGO_PSX2510_AV01.01_240208
Advertisement
Table of Contents
Related Manuals for EGO PSX2510
Summary of Contents for EGO PSX2510
- Page 1 CHAIN OIL BEFORE FIRST USE OPERATOR’S MANUAL 56-VOLT LITHIUM-ION COMMERICAL POLE SAW MODEL NUMBER PSX2510 WARNING: To reduce the risk of injury, the user must read and understand the Operator’s Manual before using this product. Save these instructions for future reference. MNL_EGO_PSX2510_AV01.01_240208...
- Page 2 Extension Pole Pole Saw Attachment End Cap Telescopic Pole Front-assist Handle Cut Line Indicator End Cap Shoulder Strap Loop Trigger Switch Quick-Release Lever Side Cove Lock-off Button Cover Nut Rear Handle Chain Tensioning Screw Battery-Release Oil Tank Cap Button Guide Ba Saw Chain Bucking Spikes Multi-function Wrench...
- Page 3 Rotation Direction Arrow Chain Drive Links Drive Sprocket Guide Bar Groove Cover Nut Side Cover Flats of drive links Approximate 1.3 mm Power Head Pole Saw Attachment...
- Page 4 Wing Knob Shaft Release Button Position Indication Arrow on the Coupler Arrow on the Pole Saw Shaft Coupler on the Extension Pole Telescopic Pole Coupler on the Power Head Quick Release Lever Extension Pole Front-assist Handle Correct Incorrect Lock Lever Shoulder Strap Loop Clamp Bolt Mounting Zone...
- Page 5 Shoulder Strap Loop Oil Tank Cap Mounting Slot Trigger Switch Press to Release Lock-off Button...
- Page 6 Cut Line indicator LOAD First Cut 1/4 Diameter Second Cut Bucking Spikes Final Cut Minimum (15m) Sprocket in Guide-bar Tip 60° Maximum Lubricating Hole Sealing Screw...
-
Page 7: Safety Symbols
Protection against water Understand IPX5 Protection read and understand jets Operator’s (IP) Rating operator’s manual before Manual using this product. Direct Type or a characteristic Current of current Volt Voltage 56-VOLT LITHIUM-ION COMMERICAL POLE SAW — PSX2510... -
Page 8: Important Safety Instructions
◾ Stay alert - Watch what you are doing. Use common ◾ Do not charge the battery pack in rain, or in wet sense. Do not operate machine when you are tired. locations. 56-VOLT LITHIUM-ION COMMERICAL POLE SAW — PSX2510... -
Page 9: Specifications
Weight (without battery pack and Replacement Parts - When servicing, use only 4.3 kg chain sheath) identical EGO replacement parts. Use of any other accessory or attachment may increase the risk of injury. 56-VOLT LITHIUM-ION COMMERICAL POLE SAW — PSX2510... -
Page 10: Recommended Accessories
NOTICE: New chains tend to stretch, check chain tension Position the chain so there is a loop at the back of frequently and adjust the tension as required. the guide bar (Fig. B3). 56-VOLT LITHIUM-ION COMMERICAL POLE SAW — PSX2510... -
Page 11: Power Head
NOTICE: This extension pole is designed to only be used with EGO A chain tensioned while it is warm may be too PSX2510. Never use it with other EGO attachments. tight upon cooling. Check the cold tension before next use. -
Page 12: Operation
Limbing ◾ To preserve natural resources, please recycle or Pruning dispose of oil properly. Consult your local waste authority for information regarding available recycling and disposal options. 56-VOLT LITHIUM-ION COMMERICAL POLE SAW — PSX2510... -
Page 13: Attaching/Detaching The Battery Pack
WARNING: Always remove the battery pack the limb falls. from the power head during work breaks and after 3. Make a final cut close to trunk. finishing work. 56-VOLT LITHIUM-ION COMMERICAL POLE SAW — PSX2510... -
Page 14: General Maintenance
Following proper cutting procedures will the motor is running. The saw chain is very sharp; always prevent stripping the bark from the main member. wear protective gloves when performing maintenance to the chain. 56-VOLT LITHIUM-ION COMMERICAL POLE SAW — PSX2510... -
Page 15: Guide Bar Maintenance
CHAIN” section. 2. Remove the chain from the guide bar. 3. Turn the guide bar over. The bottom of the bar will be on the top. 4. Replace the chain on the bar. 56-VOLT LITHIUM-ION COMMERICAL POLE SAW — PSX2510... -
Page 16: Troubleshooting
The bolt and nut on the quick Securely tighten the bolt and nut by using two 10 mm after pressing release lever became loose. socket wrenches or adjustable wrenches (not provided). down the quick release lever. 56-VOLT LITHIUM-ION COMMERICAL POLE SAW — PSX2510... - Page 17 Bar and chain run Debris in guide bar groove. Clear the debris in the groove. hot and smoke. ◾ ◾ Chain cutters are dull. Sharpen chain cutters by following the section “HOW TO SHARPEN THE CUTTERS”. 56-VOLT LITHIUM-ION COMMERICAL POLE SAW — PSX2510...
-
Page 18: Warranty Policy
EGO accessories is 90 days for residential purpose, 30 days for industrial, professional or commercial purpose. These parts are covered for 90/30 days from manufacture defects in normal working conditions. - Page 19 90 Days 30 Days *Commercial Tools include: BCX3800, BCX4500, BHX1001, CSX3000, CSX5000, EDX2000, HTX5300-P, HTX5300-PA, HTX7500, LBPX8000, LBX1000, LBX6000, LMX5300SP, PPX1000, PTX5100, PSX2500, PSX2510, STX3800, STX4500. **Commercial Batteries & Chargers include: BAX1501, CHU6000E, CHX5500E, HC2240T, PGX1400PB, PGX1600E-H, PGX3000D. 56-VOLT LITHIUM-ION COMMERICAL POLE SAW — PSX2510...
Need help?
Do you have a question about the PSX2510 and is the answer not in the manual?
Questions and answers