Related Manuals for Lincoln Electric LF 5D STANDARD
Summary of Contents for Lincoln Electric LF 5D STANDARD
- Page 1 IM3193 12/2023 REV01 LF 5D STANDARD LF 5D STANDARD (GFR) OPERATOR’S MANUAL ENGLISH Lincoln Electric Bester Sp. z o.o. ul. Jana III Sobieskiego 19A, 58-260 Bielawa, Poland...
-
Page 2: Table Of Contents
12/05 THANKS! For having choosen the QUALITY of the Lincoln Electric products. Please Examine Package and Equipment for Damage. Claims for material damaged in shipment must be notified immediately to the dealer. For future reference record in the table below your equipment identification information. Model Name, Code & Serial Number can be found on the machine rating plate. -
Page 3: Technical Specifications
Technical Specifications NAME INDEX LF 5D STANDARD K14410-1 LF 5D STANDARD (GFR) K14410-2 INPUT Input Voltage U Input Amperes I EMC Class 40Vdc 4Adc RATED OUTPUT Duty Cycle 40°C (based on a 10 min. period) Output Current 100% 420A 500A... -
Page 4: Electromagnetic Compatibility (Emc)
If any electromagnetic disturbances are detected the operator must put in place corrective actions to eliminate these disturbances with, if necessary, assistance from Lincoln Electric. Before installing the machine, the operator must check the work area for any devices that may malfunction because of electromagnetic disturbances. -
Page 5: Safety
Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or damage to this equipment. Read and understand the following explanations of the warning symbols. Lincoln Electric is not responsible for damages caused by improper installation, improper care or abnormal operation. - Page 6 WELDING SPARKS CAN CAUSE FIRE OR EXPLOSION: Remove fire hazards from the welding area and have a fire extinguisher readily available. Welding sparks and hot materials from the welding process can easily go through small cracks and openings to adjacent areas. Do not weld on any tanks, drums, containers, or material until the proper steps have been taken to insure that no flammable or toxic vapors will be present.
-
Page 7: Introduction
Introduction LF 5D STANDARD is digital wire feeder for small spool Set of power source and wire feeder allow welding in (max 200mm) which has been designed to work with listed processes: Lincoln Electric power sources: GMAW (MIG/MAG), ... - Page 8 Controls and Operational Features LF 5D STANDARD (GFR) LF 5D STANDARD Figure 4 Figure 1 Figure 5 Figure 2 Figure 6 Figure 3 English English...
- Page 9 1. EURO Socket: For connecting a welding gun (for GMAW, FCAW process). 2. Quick Coupling Socket: Coolant outlet (supplies cool coolant to the welding gun). 3. Quick Coupling Socket: Coolant inlet (takes warm coolant from the welding gun). WARNING Maximum coolant pressure is 5 bar. 4.
- Page 10 User Interface U22 Adjustments of Brake Torque of Sleeve To avoid spontaneous unrolling of the welding wire the sleeve is fitted with a brake. Adjustment is carried by rotation of its screw M10, which is placed inside of the sleeve frame after unscrewing the brake locking nut.
- Page 11 [1]. Rated parameters of the torch and welding machine should Wire Feeder LF 5D STANDARD is equipped with drive be matched. roll V1.0/V1.2 for steel wire. For others wires and sizes it ...
- Page 12 Gas Connection Transport and Lifting WARNING WARNING Falling equipment can cause injury and CYLINDER may explode if damaged. damage to unit. Always fix the gas cylinder securely in an upright position, against a cylinder wall rack or purpose-made cylinder cart. Only use the handle to move the device.
- Page 13 We respond to our customers warranty. based on the best information in our possession at that time. Lincoln Electric is not in a position to warrant or Any noticeable damage should be reported immediately guarantee such advice, and assumes no liability, with and repaired.
-
Page 14: Weee
12/05 Part List reading instructions Do not use this part list for a machine if its code number is not listed. Contact the Lincoln Electric Service Department for any code number not listed. Use the illustration of assembly page and the table below to determine where the part is located for your particular code machine. -
Page 15: Accessories
Accessories OPTIONS & ACCESSORIES K14204-1 WIRE FEEDER DRUM QUICK CONNECTOR K14175-1 GAS FLOW METER KIT KP10519-8 ADAPTER TIG EURO E/H-400A-70-5M ELECTRODE HOLDER 400A/70MM² - 5M ® W000010136 FLAIR 600GOUGING TORCH K14429-1 CONTROL PANEL COVER (SIZE A) K14430-1 PROTECTIVE CAGE (LF5D) K14431-1 PROTECTIVE CAGE WHEELS KIT (LF5D) K14432-1*... - Page 16 ROLL KIT FOR SOLID WIRES KP14420-V06/08 ROLL KIT TWIN V0.6-0.8 FI37 KP14420-V08/10 ROLL KIT TWIN V0.8-1.0 FI37 KP14420-V10/12 ROLL KIT TWIN V1.0-1.2 FI37 KP14420-V12/16 ROLL KIT TWIN V1.2-1.6 FI37 KP14420-V09/11 ROLL KIT TWIN V0.9-1.1 FI37 ROLL KIT FOR ALUMINIUM WIRES KP14420-U06/08A ROLL KIT TWIN U0.6-0.8 FI37 KP14420-U08/10A...
-
Page 17: Connection Configuration
Connection configuration English English... - Page 18 English English...
-
Page 19: Dimension Diagram
Dimension Diagram 06/23 English English...