Product Introduction; Introduction Of Mixer Panel; Front Panel - Monacor RELACART MIXX12-D Installation And Operation Manual

Product introduction

MIXX12 / MIXX12-E is a digital mixer with 12 inputs and 10 outputs. It is a new mixer
equipped with DANTE4 * 4 digital audio transmission module. You can use a network
cable to connect to the router for wireless control, or use the built-in WIFI of the mixer
for wireless control. Can support all Apple ios tablets and Windows tablets. With 6 -
channel broadcast-quality microphone amplifiers (6 combo sockets), 2 main outputs
( dual XLR + dual 6.35 sockets ), 4 auxiliary outputs, 4 DANTE outputs Adopt high -
performance 40-bit floating-point digital signal processor and 24-bit AD/DA converter.
Built-in effects processor, compression, threshold, parametric equalizer. The wireless
control mode allows you to walk on the stage and among the crowd. A 12 - channel
digital live mixer that is perfectly touchable with a tablet such as an iPad.
Features :
• Intuitive touch controls covering almost all major mixing functions.
• Mixer interface can adjust each channel control, including solo, mute, pan, fader, and see
the complete level meter.
• The channel interface can control powerful DSP effects. The input channels include 4-band
PEQ, high-pass filtering, compression, threshold, main output and auxiliary output,including
31-band graphic EQ and limiter. The effect channel includes reverb and echo.
• Each channel can be edited with names and icons for easy identification, and icons can be
imported from the picture library.
• The +48V phantom power of each channel can be individually switched.(Channel 1-channel 6)
• Extremely low noise floor and extremely high headroom design.
• 4 auxiliary outputs, 4 DANTE outputs can be used to monitor the mix.
• Globally shared reverb and echo effects.
• Seamless access, you can adjust the target's audio at any position in the network domain,
you can go directly to the stage to adjust their own monitoring, and wireless control gives the
musicians on the stage the ability to adjust their own monitoring.
• Can connect a variety of DANTE equipment, such as wireless microphones, conference
microphones, amplifiers and other equipment supporting DANTE communication.
Specification：
Sampling rate：24bit，48kHz
Frequency respond：20 Hz to 20 kHz +/–1 dB
Latency：1.5 ms
T.H.D.：<0.1%
Noise-Mic input to main output：-72dBv Single channel-Max fader(A weighted)
-90dBv Single channel-Min fader(A weighted)
Input crosstalk(adjacent channel)：<–120 dB @1 kHz
S/N：93dB One channel and main fader at unity(A-weighted)
Dynamic Range：110dB One channel and main fader at unity(A-weighted)
CMRR：>70 dB @1 kHz
Input Impedance：3.3k Ω(XLR Balance); 30 kΩ(1/4")
Gain：0 to 60 dB
Output Impedance：600Ω(XLR Balance)
Max Output Level：+21 dBu(XLR Balance)
Power Supply：100-240V AC 50/60Hz
Dimension(mm)：488(L)x 132(H)x 191(D)
Weight：Approximately 4kg

Introduction of Mixer Panel

Front panel:

1. WIFI antenna socket: Install the factory configured WIFI antenna.
2. WIFI: The WIFI indicator flashes when transmitting data.
3. POWER: The power indicator is on to indicate that the power is on.
4. Monitor socket: 6.35MM stereo monitor output socket.
5. PHONE: Stereo monitor output volume adjustment potentiometer.
6. MAIN L OUTPUT potentiometer: The main output left channel volume potentiometer.
7. MAIN R OUTPUT potentiometer: The main output right channel volume potentiometer.
8. Input channel ( MIC / LINE ) : 1-6 channels XLR and 6.35 jack ( JACK ) compatible
balanced input. Cannon type can independently control 48V phantom power.
9. Input channel LINE: 7-12 channel 6.3 jack balanced input.
10. Auxiliary output (AUX 1-AUX4): 4 unbalanced auxiliary outputs, each independently
controlled.
11. MAIN L / R OUTPUTS: The main output XLR and JACK are output in parallel with the
same signal.
12. MAIN L / R OUTPUTS: The main output XLR and JACK are output in parallel with the
same signal.
13. MAIN L / R OUTPUTS LED: main output audio indicator, not controlled by main output
volume potentiometer