Settings - GE GRS500PV Owner's Manual

Settings

There are several settings on your range. To access and change these settings, press the Bake and Broil pads at the same
time and hold for three seconds, a beep sounds, then release the buttons and "OFSt" should appear in the display.
Scroll through the Settings menu using the 2 number pad for up and the 8 number pad for down until the desired feature is
displayed. To select a feature to change, or to confirm a change, press the 6 number pad. To cancel a change and return to
the Settings menu, press the 4 number pad. To exit the Settings menu, press Cancel.
Adjust the Oven Temperature (OFSt)
This feature allows the oven baking temperature to be
feature if you believe your oven temperature is running too
hot or too cold and wish to change it.
To adjust the oven temperature, enter the Settings menu as
listed above, then scroll through the features until "OFSt" is
displayed and press Start. A number between 35 and -35
adjusted temperature or use the 8 number pad to decrease
the adjusted temperature. Press 6 to save the temperature
adjustment. Press Cancel to exit the Settings menu. This
running too hot or too cold and wish to change it. Do not
use thermometers, such as those found in grocery stores, to
check the temperature inside your oven. These thermometers
may vary 20-40 degrees.
Sabbath Warmer Setting (Sabb)
This feature allows the user to increase the Sabbath Warm
temperature if the oven is operating cooler than desired.
To adjust this feature Lo or Hi, enter the Settings menu as
outlined above and scroll through the options until "Sabb" is
displayed, then press 6. Scroll to the desired option and press
6 again to confirm. Press Cancel to exit the Settings menu.
Sound Volume (Snd)
This feature allows the oven tone volume to be adjusted On
and Off (OFF). To adjust the tone volume, enter the Settings
menu as outlined above and scroll through the options until
"Snd" is displayed, then press 6. Scroll to the desired option
and press 6 again to confirm it. Press Cancel to exit the
Settings menu.
End of Timer Signals (End tonE)
This is the tone that signals the end of a timer. The tone
can be continuous (Cont) or one repeating beep (bEEP). A
continuous setting will continue to sound a tone until a pad
on the control is pressed. A single setting (bEEp) will sound
just a single tone at the end of the timer. To change the tone,
enter the Settings menu as outlined above and scroll through
the options until "End tonE" is displayed, then press 6. Scroll
to the desired option and press 6 again to confirm it. Press
Cancel to exit the Settings menu.
12-hr Auto Shut Off (12h Shut)
This feature turns off the oven after 12 hours of continuous
operation. To enable or disable this feature, enter the
Settings menu as listed above and scroll through the options
until "12h Shut" is displayed, then press 6. Scroll to the
desired option and press 6 again to confirm it. Press Cancel
to exit the Settings menu.
Fahrenheit / Celsius (dEg Unit)
The oven control is set to use Fahrenheit temperatures
(F), but you can change it to use Celsius temperatures (C).
8
To toggle between temperature measurements, enter the
Settings menu as listed above and scroll through the options
until "dEg Unit" is displayed, then press 6. Scroll to the
desired option and press 6 again to confirm it. Press Cancel
to exit the Settings menu.
Clock Display (CLoc diSP)
This feature specifies whether the clock appears in the
display. The clock display may be "On" or "OFF." To change
the display, enter the Settings menu as listed above and
scroll through the options until "CLoc diSP" is displayed,
then press 6. Scroll to the desired option and press 6 again to
confirm it. Press Cancel to exit the Settings menu.
Clock Configuration (CLoc cFg)
This feature specifies how the time of day will be displayed.
You can select a standard 12-hour clock (12) or 24-hour
military time display. To change the configuration, enter
the Settings menu as outlined above and scroll through the
options until "CLoc cFg" is displayed, then press 6. Scroll
to the desired option and press 6 again to confirm it. Press
Cancel to exit the Settings menu.n to confirm it. Press
Cancel to exit the Settings menu.
Remote Enable (APP EnbL)
(available with U+ Connect module)
Allows you to control your oven remotely. This feature may
be "on" or "oFF." To change the configuration, enter the
Settings menu as outlined above and scroll through the
options until "APP EnbL" is displayed, then press 6. Scroll
to the desired option and press 6 again to confirm it. Press
Cancel to exit the Settings menu.
UPD (uPd)
(available with U+ Connect module)
service about your oven. To access the information, enter the
Settings menu as outlined above and scroll thru the options
until "uPd" is displayed, then press 6. A set of four characters
and numbers will display. Scroll down to see the next set of
four characters and numbers and then scroll down again to
see the final set of four characters and numbers. You can
also scroll up to review the previous sets. Press Cancel to
exit the Settings menu.
MAC ID (id)
(available with U+ Connect module)
Wi-Fi systems. To access the information, enter the Settings
menu as outlined above and scroll thru the options until "id" is
displayed, then press 6. A set of four characters and numbers
will display. Scroll down to see the next set of four characters
and numbers and then scroll down again to see the final set of
four characters and numbers. You can also scroll up to review
the previous sets. Press Cancel to exit the Settings menu.
49-2001190 Rev. 0