Advertisement
USING THE CONTROL PANEL
NOTE: Press the dial to START and/or STOP any program.
POWER
MANUAL
BLENDSENSE
Variable speed control for
Intelligent one-touch program
blending total control.
that senses your ingredients
and blends to perfection.
MODE
Preset programs that chop and mince.
PROCESSING MODE PROGRAMS
CHOP FUNCTIONS: Pitcher only
Smart preset programs that combine unique blending and pausing
patterns that chop for you. When selected, each will start immediately
and automatically stop. Press the dial again to stop the program sooner.
They do not work in conjunction with the BlendSense Program or Manual Mode.
NOTES:
• Number of seconds is displayed for each program runtime.
• Functions vary by model. Refer to your Quick Start Guide for your model's specific configuration.
MANUAL MODE
Go manual for total control of your blending speed and textures. Dial down the
speed for heavy loads or crank up the speed for light loads like smoothies. When
selected, each speed runs continuously for 60 seconds. Press the dial again to
stop the program sooner. Manual mode does not work in conjunction with the
BlendSense or Processing Mode Programs.
START SLOW: Always start at low speed to better incorporate ingredients and
prevent them from sticking to the sides of the vessel.
DIAL UP THE SPEED: Smoother blends call for higher speeds. Low speeds are
great for chopping veggies, but you'll need to ramp up for purees and dressings.
HIGH-SPEED BLENDING: Blend until your desired consistency is reached. The
longer you blend, the better the breakdown and smoother the outcome will be.
TB300: LOW, MEDIUM, HIGH: Pitcher and Single-Serve Cup
TB301: VARIABLE SPEED CONTROL (1–10): Pitcher only
LOW, MEDIUM, HIGH: Single-Serve Cup only
NOTES:
• Number of seconds is displayed for each program runtime.
• Functions vary by model. Refer to your Quick Start Guide for your model's specific configuration.
ninjakitchen.com
USING THE POWER BLENDER & PROCESSOR PITCHER
IMPORTANT:
• Review all warnings at the beginning of this Owner's Guide before proceeding.
• As a safety feature, if the pitcher and lid are not properly installed, the timer will display "... ..." and
the motor will be disabled. If this happens, repeat step 5 on this page. When the pitcher and lid are
properly installed, the program button LEDs will illuminate, indicating the appliance is ready to use.
WARNING:
locked onto the blender pitcher. Failure to do so will result in a risk of laceration.
PULSE
WARNING:
Offers greater control
remove the Stacked Blade Assembly first, holding it by the shaft. Failure to do so will result in a risk of laceration.
of pulsing and blending.
Operates only when PULSE
NOTES:
is pressed. Use short presses
• Programs have pauses and changes in speed throughout the cycle.
for short pulses and long
presses for long pulses.
• DO NOT add ingredients before completing installation of the Stacked Blade Assembly.
• If the Stacked Blade Assembly is not fully seated, you will not be able to install and lock the lid.
• The pitcher lid handle will not fold down unless it is attached to the pitcher.
1
Plug in motor base and place on a clean, dry, level surface such as a
countertop or table.
2
Lower the Power Blender & Processor Pitcher onto the motor base. The
handle should be aligned slightly to the right and the pitcher should be
oriented so the LOCK symbols are visible on the motor base. Rotate the
pitcher clockwise until it clicks into place.
3
Exercising care, grasp the Stacked Blade Assembly by the top of the shaft
and place it onto the drive gear inside the pitcher. Note that the blade
assembly will fit loosely onto the drive gear.
6a If using the BlendSense program, simply press the dial. The program will
automatically stop once complete. To stop the unit at any time, press the dial again.
6b If using a processing mode program, select the mode button then use the
dial to select your desired program. To start, press the dial. The program will
automatically stop once complete. To stop the unit at any time, press the dial again.
6c If using a manual program, select the manual button then use the dial to select
your your desired speed. To start, press the dial. Once the ingredients have
reached your desired consistency, press the dial again or wait 60 seconds
for the unit to come to a complete stop.
7
To remove the pitcher from the motor base, turn the pitcher counterclockwise and then lift up.
ninjakitchen.com
Stacked Blade Assembly is sharp and not locked in place. If using the pour spout, ensure the lid is fully
Stacked Blade Assembly is sharp and not locked in place. If pouring with the lid removed, carefully
4 Add ingredients to the pitcher. DO NOT add ingredients past the MAX LIQUID line.
5
Place the lid on the pitcher, aligning the triangle symbol on the lid with the triangle
symbol on the handle. Press down on the handle until it clicks into place. The triangle
symbols MUST be aligned for the lid to lock and the unit to operate. Once the lid is
locked in place, press the Power button to turn unit on. The BlendSense program
will illuminate.
8a To pour out thinner mixtures, ensure the lid is locked in place, then open
the pour spout cap.
8b For thicker mixtures that cannot be emptied through the pour spout,
remove the lid and Stacked Blade Assembly before pouring. To remove
the lid, press the RELEASE button and lift the handle. To remove the
blade assembly, carefully grasp it by the top of the shaft and pull straight
up. The pitcher can then be emptied.
9 Turn the unit off by pressing the Power button. Unplug the unit when
finished. Refer to the Care & Maintenance section for cleaning and
storage instructions.
ninjakitchen.com
ninjakitchen.com
Advertisement
