Denon DRA-625R Operating Instructions Manual page 5

TAPE SELECTOR (Tape selector switch)
Toggle keys have been used for selection of TAPE-1 and
TAPE-2. Pressing them an uneven number of times turns
the function on, pressing them an even number of times
turns the function off.
e@ TAPE-1: Used to play a tape deck connected to the
TAPE-1 terminal.
e TAPE-2: Used to play a tape deck connected to the
TAPE-2 terminal.
Tape-to-Tape Dubbing
@® Connect the two tape decks to this unit as shown in
the connections.
@ Load the original tape in tape deck 1 and the blank
tape in tape deck 2.
@ Press the TAPE-1 Selector Button @® (indicator
lights).
@® Put tape deck 1 in the playback mode and tape deck 2
in the recording mode. Follow tape deck operating
instructions.
© The recording can be monitored through the speak-
ers or headphones. (If tape deck 2 has three heads,
the just-recorded signal can be monitored when the
tape 2 button is pressed.)
TUNING (Tuning Buttons)
Use these buttons for either manual tuning or automatic
tuning.
e@ UP: When this button is pressed, the tuning
goes up the band.
e DOWN: When this button is pressed, the tuning
goes down the band.
e Manual Tuning (Set the TUNING MODE @ "MANU" by
pushing the TUNING MODE Button ®.)
In FM mode, the frequency indicator moves in 50 kHz
steps. In am, the indicator moves in 9 kHz steps. If the
button is pressed for more than 1 second, the indicator
moves quickly and continuously up or down until
released.
DISPLAY
(1 kHz
Ci MHz
FM MODE (STEREO/MONO Indicator)
Lights automatically when receiving a stereo signal in the
"STEREO" mode. Does not light for stereo reception in the
"MONO" mode.
TUNING MODE (AUTO/MANUAL)
Pressing TUNING MODE ® causes AUTO and MANU to
light up alternately.
SHIFT [A] [B] (Shift Indicator)
The preset channel which is selected with the Shift Button
® is displayed by the SHIFT [A] or [B).
SIGNAL LEVEL (Signai-Level Indicators)
This indicator shows the signal strength level of AM and
FM broadcast station. The best position for reception is
obtained when the maximum number of indicator lamps
are illuminated.
7)
®
1 Cimemo
ENGLISH
e Automatic Tuning (Set the TUNING MODE @ "AUTO"
by pushing the TUNING MODE Button @.)
For example, when the "up" button is pressed, the
frequency indicator moves up the band until a broad-
cast signal is received.
If no more signals are detected, the indicator moves to
the upper limit and starts from the lower end.
(When the "down" button is pressed, the indicator
travels down in the same way.)
While the button is continuously pressed, broadcast
signals cannot be tuned; the indicator continuously
travels up or down the band. Automatic tuning is only
provided for radio stations of usable strength; a sudden
strong noise may disturb automatic tuning.
When the desired signal is weak, use manual tuning.
SHIFT (Shift Button)
This switch is used to change eight preset buttons @ to 1 ~
8 channels or 9 ~ 16 channels. The SHIFT [A]/[B] is then on.
Each recycle shifts from SHIFT [A] to SHIFT [B]. If storing or
retrieving data into or from the preset 1 ~ 8 channels,
specify SHIFT [A]. Similarly, to use preset 9 ~ 16 channels,
specify SHIFT [B].
MEMORY (Memory Button)
This switch is used to register the desired radio station to
one of the preset buttons memory. When pressing this
button, the memory indicator ® lights for approximately 5
seconds. During this interval, the desired station can be
registered in the memory.
PRESET CHANNEL 1 ~ 16 (Station Presetting But-
tons)
These buttons are used for storing or calling station. With
the shift button @ you can preset 1 ~ 8 and 9 ~ 16
channels, a total of 16 AM and FM stations in eight preset
buttons. When the preset channel buttons are in operation,
an indicator (SHIFT [A] /[B)) illuminates. When radio stations
are memorized with these buttons, a desired station can be
easily tuned in without pressing the tuning buttons.
— FUNCTION —___
© TUNER © co © PHONO
OTAPE-2 © TAPE-1 © AUX/VIDEO
SIGNAL ' 2 3
LEVEL 90° 00 00
FUNCTION (input Selector Indicator)
The program source selected by input Select Switin or
Tape Select Switch is displayed by the indicator.
MEMO (Memory indicator)
This indicator lights when the MEMORY button @ is
pressed.
CHANNEL
When using the channel preset button ®, the chanel is
displayed and the frequency for that channel stor in
memory is displayed in @.
FREQUENCY DISPLAY (Frequency Indicator)
The frequency is displayed in numerals. It is displayed in
MHz for FM and in kHz for MW.