Installer Parameters; Service Parameters - Riello RESIDENCE HM Series Instructions For The User

INSTALLER PARAMETERS

MENU PARAMETER
P2 COMBUSTION
P201 GAS - GAS TYPE
P205 d52 - P1 GAS VALVE
P206 GAC - VALVE CALIBRATION
P208 APL - POWER
P3 CONFIGURATION
P301 HYDRAULIC CONFIGURATION
P306 MIN FAN SPEED
P307 MAX FAN SPEED
P309 MAX FAN SPEED HTG
P310 RANGE RATED
P311 CONFIG AUX 1
P312 EXHAUST PROBE RESET
P4 HEATING
P405 PUMP CONTROL TYPE
P408 OT CASCADE CONTROL
SCREED FUNCTION
P409
P410 ANTI CYCLE FUNCTION
P411 RESET CH TIMERS
P415 MAIN ZONE TYPE
P416 MAX CH SET
P417 MIN CH SET
P418 WEATHER COMP ENABLE
P419 WEATHER COMP CURVE
P420 NIGHT COMPENSATION
P421 CH CLOCK ENABLE
P422 MODE SELECTION
P433 BUILDING TYPE
P434 OUTDOOR REACTIVITY
HT = HIGH TEMPERATURE
P5 DHW (°°)
P501 ANTI LEGIONELLA FUNCTION
P502 ANTI LEG. TIME PERIOD
P503 ANTI LEG. TEMPERATURE
P504 TANK HYSTERESIS ON
P505 TANK HYSTERESIS OFF
P506 TANK FLOW TEMP
P507 MODULATING TANK SUPPLY TEMP
P508 MIN DHW SET
P509 MAX DHW SET
P511 DHW ENHANCED FUNCTION

SERVICE PARAMETERS

MENU PARAMETER
P3 CONFIGURATION
P302 WATER PRESSURE TRANSDUCER
P303 AUTO-FILL ENABLE
P304 BEGIN SYSTEM FILLING
P305 AIR PURGING CYCLE
P4 HEATING
P401 HYST OFF HIGH TEMP
P402 HYST ON HIGH TEMP
P403 HYST OFF LOW TEMP
P404 HYST ON LOW TEMP
P5 DHW (°°)
P510 DHW DELAY
P512 CH DELAY POST-DHW
P513 CH DELAY TIME
P7 SERVICE
P701 ENABLE ALARM LOG
P706 CALL SERVICE FUNCTION
P707 SERVICE EXPIRY
P708 HIGH EFFICIENCY ENABLE
P8 CONNECTIVITY
P801 BUS 485 CONFIG
P803 OT CONFIG
*P301: 0 = HEATING ONLY - 1 = INSTANTANEOUS WITH FLOWSWITCH - 2 = INSTANTANEOUS WITH FLOWMETER - 3 = STORAGE CYLINDER WITH PROBE - 4 = STORAGE
CYLINDER WITH THERMOSTAT.
(°°) P5 - DHW menu can only be used when parameter 301 HYDRAULIC CONFIGURATION is = 3 (case C) or 4 (case B)
Min
1
20
0
0 (25kW)
0
1000 rpm
3700 rpm
P306
(MIN FAN SPEED)
0
0
41
0
0min
0
0
MIN CH SET
20°C
0
HT: 1.0 - LT: 0.2
0
0
0
5
0
LT = LOW TEMPERATURE
0
0h
65°C
0°C
0°C
50°C
0
37°C
49°C
Min
0
0
0
2°C
2°C
2°C
2°C
0
1 sec
0
0
0
0
0
0
Value
Password level
Max
4
70
1
only if there is a fl ame
1 (35kW)
4
3600 rpm
10000 rpm
P307
(MAX FAN SPEED)
DO NOT CHANGE
2
1
100
NOT USED ON THIS MODEL
INSTALLER: if boiler in
1
OFF and LT systems
30min
1
1
HT: 80°C - LT: 45°C
MAX CH SET
1 if outdoor temperature
HT: 3.0 - LT: 0.8
only if P418 = 1
1
1
1
20
only if P418 = 1
255
2
24h
85°C
10°C
10°C
85°C
1
49°C
60°C
NOT USED ON THIS MODEL
Value
Password level
Max
1
1
NOT AVAILABLE ON THIS MODEL
1
10°C
10°C
10°C
10°C
NOT AVAILABLE ON THIS MODEL
1
255 sec
1
2
255
1
2
1
20
Factory setting
INSTALLER 1
INSTALLER
45
if boiler in OFF
INSTALLER
0
INSTALLER 0
INSTALLER 0*
INSTALLER refer to technical data table
INSTALLER refer to technical data table
INSTALLER refer to technical data table
INSTALLER 0
INSTALLER 0
INSTALLER 85
0
INSTALLER 3min
INSTALLER 0
INSTALLER 0
INSTALLER HT: 80°C - LT: 45°C
INSTALLER HT: 40°C - LT: 20°C
INSTALLER
0
sensor present
HT 2.0 - LT 0.5
INSTALLER
0
0
0
5
INSTALLER
20
INSTALLER 0
INSTALLER 0h
INSTALLER 80°C
INSTALLER 5°C (ext) - 0,5°C (int)
INSTALLER 5°C (ext) - 0°C (int)
INSTALLER 80°C
INSTALLER 0
INSTALLER 37°C
INSTALLER 60°C
Factory setting
SERVICE 1
SERVICE 0
SERVICE 1
SERVICE 5°C
SERVICE 5°C
SERVICE 3°C
SERVICE 3°C
SERVICE 0
SERVICE 6 sec
0
(the value automatically
SERVICE
switches to 1 after 2
hours of operation)
SERVICE 2
SERVICE 52
SERVICE 0
SERVICE 0
SERVICE 1
Customised
values
Customised
values