Advertisement
Available languages
Available languages
EnGLIsH
Attaching the Side Handle (Fig. H)
WARNING: This handle SHOULD BE USED AT ALL
TIMES to maintain complete control of the tool.
Always make sure the handle is tight.
Screw the side handle
tightly into the threaded mounting
5
hole of the filehead body
23
Attaching the Dust Shroud (Fig. H)
The DCM200DC dust shroud is included with this tool. This
accessory connects to the tool's filehead body.
To attach the dust shroud
10
from the tool.
1. Place the ribs
24
of the dust shroud
of the filehead body
23
2. Position the dust port
11
the dust port hole align with the filehead body hole.
3. Use the side handle
5
filehead body.
Attaching a Dust Extractor to the Dust Shroud
(Fig. P, Q)
WARNING: Do not attach the dust port and connect the
dust extractor when grinding or sanding metals.
WARNING: Risk of dust inhalation. To reduce the risk of
personal injury, ALWAYS wear an approved dust mask.
WARNING: Collected sanding dust from sanding
surface coatings (polyurethane, linseed oil, etc.) can
self-ignite in dust extractor or elsewhere and cause fire.
To reduce risk, strictly follow sander manual and coating
manufacturer's instructions.
The DCM200DC dust shroud is compatible with the DWH161
DEWALT Universal Dust Extractor (sold separately).
•
Friction‑fit the dust port
Universal Dust Extractor.
If available, the DWV9170 adaptor
your tool to the D
WALT AirLock™ connection system
e
(sold separately).
1. Push the AirLock™ connector
DWV9170 adaptor.
2. Friction‑fit the DWV9170 adaptor to the dust port.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: DO NOT touch the filehead body during use
as a high temperature may cause injury.
40
.
, FIRST disconnect the battery
10
along the groove
.
against the filehead body to let
to tighten the dust shroud to the
11
to the hose
25
of the DWH161
30
can be used to connect
31
onto the
Proper Hand Position (Fig. J)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
and one hand on the side handle
LED Worklight (Fig. A, N)
CAUTION: Do not stare into the LED worklight.
Serious eye injury could result.
The rotatable LED worklight
levels through an angle of 60 °. When the tool is activated by
depressing the variable speed trigger
worklight will automatically turn on. The rotatable LED worklight
will turn off 20 seconds after the variable speed trigger has
been released.
nOTE: Be careful not to scratch the lens of the worklight as loss of
illumination may occur. Use a dry cloth to wipe dirt off the lens of
the worklight.
Variable Speed Dial (Fig. O)
The variable speed dial
1
allows you to adapt the speed of the
tool to the workpiece material.
The tool speed can be adjusted between 1 to 7.
Use a low speed setting when using a fine grit, when working
with plastics or ceramics and when removing painted or
varnished surfaces.
Use a high speed setting when using a coarse grit and when
removing a lot of material.
•
Set the variable speed dial
Switching On and Off (Fig. A)
CAUTION: DO NOT pull the variable speed trigger hard
without first unlocking the tool. Refer to the Lock‑off
Button section. This can cause a breakage to the variable
speed trigger.
1. To start the tool, pull the variable speed trigger
2. To turn the tool off, release the variable speed trigger.
Lock‑off Button (Fig. I)
WARNING: To prevent accidental start-up, this tool is
equipped with a lock-off button.
1. To lock the tool, depress the lock‑off button
position. When the lock‑off button is in the locked position,
the tool is locked and the variable speed trigger
be pulled.
2. To unlock the tool, depress the lock‑off button
unlocked position.
nOTE: The tool is locked and the speed trigger can't be
pulled while the arm is being pivoted to the storage position
(beyond 102 °).
5
.
12
can be adjusted at three
, the rotatable LED
2
1
to the required setting.
.
2
to the locked
3
2
cannot
to the
3
4
Advertisement
