Lens Block Section - Sony Cyber-shot DSC-RX100M3 Service Manual

2018/10/17 03:17:13 (GMT+09:00)
Ver. 1.3 2016.11
The changed portions from
Ver. 1.2 are shown in blue.

2-1-8. LENS BLOCK SECTION

ns : not supplied
351
(Note 1, 2)
ns
354
(Claws)
353
(Note 3)
352
Note 4: When this part is removed, adjustment is required.
For the adjustment method, refer to "Adjustment items after
replacing parts" in the Note tab of the Adjust manual.
Note 5: Refer to "1-3. NOTES ON REMOVING/INSTALLING THE
IMAGER BOARD (CD-847 FLEXIBLE BOARD)".
Note 6: Be sure to read "Precautions for Replacement of Imager" on
page 6-1 of Level 3 when changing the imager.
Ref. No. Part No. Description
351 A-2057-540-A SERVICE, LENS DEVICE LSV-1710A (Note 1, 2)
352 A-2080-831-A RING (A) (SERVICE), ORNAMENTAL
353 4-531-005-01 TAPE, BARRIER (Note 3)
354 A-2032-894-A BARRIER BLOCK ASSY
355 4-294-347-01 RETAINER, FG
356 A-2049-433-A DC MOTOR WORM ASSY
357 A-2032-915-A LUBRICATING BLOCK ASSY, WHEEL
358 A-1940-536-A GEAR A LUBRICATED ASSY
359 A-2032-916-A LUBRICATING BLOCK ASSY, (B)
360 Selection Parts SPACER PLATE
DSC-RX100M3/RX100M3G_L2
ns
#302
#258
361
360 (including CP001
(CMOS imager) and
ns
CD-847 flexible board)
(Note 4, 5, 6)
#258
ns
ns
359
358
357
#176
356
(Claw) 355
(Claws)
ns
Note 4: この部品を取り外したときは調整が必要です。
調 整 方 法 に つ い て はAdjust manualのNoteタ ブ に あ る
Adjustment items after replacing partsを参照してください。
Note 5: "1-3. イメージャ基板 (CD-847フレキシブル基板) の取り外し／
取り付け時の注意" を参照してください。
Note 6: イメージャの交換時はLevel 3の6-1ページ，"イメージャ交換
時の注意" を必ずお読みください。
Ref. No. Part No. Description
361 A-2057-541-A INDIVIDUAL, FILTER BLOCK ASSY (including CP001
(CMOS imager) and CD-847 flexible board) (Note 4, 5, 6)
362 4-573-348-01 INSULATING SHEET (ST3) (609) (Note 7)
363 A-2009-287-A LF-2091 FLEXIBLE BOARD, COMPLETE
#176 3-947-504-31 SCREW (M1.2)
#258 4-299-468-11 SCREW, TAPPING UB1.2 (CH)
#302 3-703-816-18 SCREW (M1.4X3.5), SPECIAL HEAD
DISASSEMBLY
1. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇-X: Solder
Screw
#176: M1.2 X 2.0
(Silver)
3-947-504-31
1.2
362
(Note 7)
2.0
Note
ns
Note 1: NOTES ON HOLDING THE LENS BLOCK
363
Hold the Lens Block at the
center of both sides.
Note 2: Refer to the following each item when you exchange parts of
Lens Block.
• 1-9. ORNAMENTAL RING (A) OR BARRIER BLOCK ASSY
REPLACING METHOD (page 1-9)
• 1-10. 1 GROUP FRAME BLOCK ASSY REPLACING
METHOD (page 1-9)
Note 3: Do not reuse the Barrier Tapes because its adhesive force
decreases when it is removed once.
NOTES ON INSTALLING THE INSULATING SHEET (ST3) (609)
Note 7:
That it does not overlap on the rib.
Paste it to the edge of the sheet.
2-11
#258: M1.2 X 3.5 (Tapping) #302: M1.4 X 3.5
(Silver) (Silver)
3-703-816-18
4-299-468-11
1.4
1.2
3.5
3.5
Do not hold the following part.
Hold here.
Zoom motor,
Lens barrier
Gear B
*Very weak
*Very weak
Note 2: レンズブロックの各部品を交換する際は，下記の各項目を参照
してください。
・ 1-9. ORNAMENTAL RING (A) OR BARRIER BLOCK
ASSY REPLACING METHOD (page 1-9)
・ 1-10. 1 GROUP FRAME BLOCK ASSY REPLACING
METHOD (page 1-9)
Note 3: Barrier Tapeは一度剥がすと粘着力が弱くなるため，再利用は
しないでください。
Reference 2 (vertical walls):
INSULATING SHEET (ST3) (609)
The right and left is less than 1mm.
G10 lens
*Very weak
Reference 1 (vertical walls):
The inside is less than 1mm.
SYS SET