Related Manuals for W&T 55614
Summary of Contents for W&T 55614
- Page 1 Manual Installation and application Ethernet Gigabit Switch Valid for #55614 Release 1.00 11/2021...
-
Page 2: Table Of Contents
Inhalt Content 1. Legal notices ..............3 Warning notice system ..................3 Qualified personnel .................... 3 Disposal ......................4 Symbols on the product ..................4 2. Safety notices ..............5 General notices ....................5 Intended use ....................... 5 Electrical safety ....................5 3. -
Page 3: Legal Notices
Legal notices 1. Legal notices Warning notice system This manual contains notices that must be observed for your personal safety as well as to prevent damage to equipment. The notices are emphasized using a war- ning sign. Depending on the hazard level the warning notices are shown in decrea- sing severity as follows. -
Page 4: Disposal
Legal notices ly the safety and warning notices contained therein. Qualified personnel are defined as those who are qualified by their training and experience to recognize risks when handling the described products and to avoid possible hazards. Disposal Electronic equipment may not be disposed of with normal waste, but rather must be brought to a proper electrical scrap processing facility. -
Page 5: Safety Notices
Safety notices 2. Safety notices General notices This manual is intended for the installer of the Gigabit Switch described in the ma- nual and must be read and understood before starting work. The devices are to be installed and put in operation only by qualified personnel. Intended use 1DANGER The Ethernet Gigabit switch made by Wiesemann &... - Page 6 Safety notices that the lead is fully contained in the clamp and that the screws are tightly fastened. Fully tighten screws on unused terminals. The power supply used for the Gigabit Switch must absolutely ensure safe isolation of the low-voltage side from the supply mains according to EN62368-1 and must have “LPS“...
-
Page 7: Quick Startup
Quick Startup 3. Quick Startup Network connection Supply voltage 12V .. 48DC The switch is ready for standard operation after a few seconds. -
Page 8: Product Introduction
Product introduction 4. Product introduction Hardware The W&T Gigabit Swicht has four equal RJ45 Ethernet ports for connecting Ethernet end devices and is supplied with a voltage between 12V and 48V DC. Front DIL switches Back Port 1 1 = OFF - Standard port 1 = ON - Mirror port Port 2 2 = OFF - Standard port... -
Page 9: Operating Modes
Operating modes 5. Operating modes Standard Gigabit-Switch When delivered, the switch works as a normal switch with four autosensing ports with equal rights. DIL-Switch 1 = OFF 2 = OFF 3 = OFF 4 = OFF 5 = OFF 6 = OFF 7 = OFF 8 = OFF Each port automatically detects the transmission rate and whether data transmissi-... -
Page 10: Monitoring
Operating modes Monitoring The W&T Switch allows any port to be working as a monitor or mirror port. max. Monitoring DIL-Switch 100MBit/s 1 = OFF max. 100MBit/s 2 = ON 3 = OFF max. 4 = OFF 100MBit/s 5 = OFF max. -
Page 11: Hub Mode
Operating modes HUB Mode In HUB mode, all traffic handled by the switch is send to all four ports. max. DIL-Switch 100MBit/s 1 = OFF max. 100MBit/s 2 = OFF 3 = OFF max. 4 = OFF 100MBit/s 5 = ON max. -
Page 12: Technical Data
Technical data 6. Technical data Gigabit-Switch #55614 Network: 4 x 10/100/1000 BaseT autosensing Power supply: 12-48V DC (approx. 150mA@24V) Idle @24V - 52mA @48V - 33mA 1 port activ @24V - 78mA @48V - 41mA 2 port activ @24V - 100mA @48V - 48mA...