Please refer to the latest version of the documentation, which is ready for download under www.thomann.de. 1.1 Symbols and signal words In this section you will find an overview of the meaning of symbols and signal words that are used in this document. Crown FX LED Spotlight...
Page 6
This combination of symbol and signal word indicates a pos‐ sible dangerous situation that can result in material and environmental damage if it is not avoided. Warning signs Type of danger Warning – high-voltage. Warning – dangerous optical radiation. Warning – suspended load. Crown FX LED Spotlight...
Page 7
General information Warning signs Type of danger Warning – danger zone. Crown FX LED Spotlight...
Always dispose of packaging material properly when it is not in use. Never allow children to use the device without supervi‐ sion. Keep small parts away from children and make sure that the device does not shed any small parts (such knobs) that children could play with. Crown FX LED Spotlight...
Page 9
Never cover the device or the vents. Do not install the device in the immediate vicinity of other heat sources. Never operate the device in the immediate vicinity of naked flames. Crown FX LED Spotlight...
Page 10
Also refer to the specifications in the technical specifications for the device. Only use power cords with a cable cross-section designed for the required current intensity when connecting the devices in series. Crown FX LED Spotlight...
Page 11
Using fuses of a different type than compatible with the device may cause a fire and seriously damage the device. Only use fuses of the same type. Observe the labelling on the device casing and the information in the "Technical data” chapter. Crown FX LED Spotlight...
For technological reasons, the light output of LEDs decreases over their lifetime. This effect increases with higher operating temperature. You can extend the service life of the illuminants by providing adequate ventilation and operating the LEDs with the lowest possible brightness. Crown FX LED Spotlight...
Always work from a stable platform whenever installing, moving or servicing the device. While you do this, the area underneath the device must be cordoned off. The safety cable must be threaded through the safety cable eyelet. Crown FX LED Spotlight...
Page 14
Make sure that illuminated surfaces are more than 2 m away. Do not operate the device in ambient temperatures above 40 °C. Always ensure sufficient ventilation at the operating location. Crown FX LED Spotlight...
Page 15
Always ensure that the stand is stable. Infrared sensor for the remote The infrared sensor for the signals of the remote control is located on the front, near the cen‐ control tral LED. Make sure it is not obstructed. Crown FX LED Spotlight...
Page 16
Possible damage due to leaking batteries! Batteries can leak and cause permanent damage to the device. Take the batteries out of the device if it is not going to be used for an extended period of time. Crown FX LED Spotlight...
If the DMX connections are wired incorrectly, this can cause errors during the data transfer. Do not connect the DMX input and output to audio devices, e.g. mixers or ampli‐ fiers. Use special DMX cables for the wiring instead of normal microphone cables. Crown FX LED Spotlight...
Page 18
Connect the DMX output of the master device to the DMX input of the first slave device. Then connect the DMX output of the first slave device to the DMX input of the second slave device and so on. Crown FX LED Spotlight...
Connections and operating elements Connections and operating elements ö SENSITIVITY & MENU UP DOWN ENTER DMX IN DMX OUT Crown FX LED Spotlight...
Page 20
9 [SENSITIVITY] | Control for adjusting the sensitivity of the built-in microphone 10 [DMX IN] | DMX input, designed as XLR chassis plug [DMX OUT] | DMX output, designed as XLR chassis socket 11 Safety cable eyelet Crown FX LED Spotlight...
Press [MENU] repeatedly until the display shows ‘Sou’ . Confirm with [ENTER] and use [UP] or [DOWN] to select one of 13 colour LED shows ‘S01’ … ‘S12’ . Confirm with [ENTER] to apply the setting. Crown FX LED Spotlight...
Page 22
Use [UP] or [DOWN] to select the submenu ‘S.xxx’ . Confirm with [ENTER] and use [UP] and [DOWN] to set the flash frequency for the strobe effect in a range from ‘S.001’ (slow) to ‘S.099’ (fast). Confirm again with [ENTER] to apply the setting. Crown FX LED Spotlight...
Page 23
This setting is only relevant when the device is the slave in a master/slave configuration and is not operated via DMX. Press [MENU] repeatedly until the display shows ‘SLA’ . Press [ENTER] to activate slave mode. Crown FX LED Spotlight...
Page 24
Proceed as follows to reset the device to factory defaults: Press [MENU] repeatedly until the display shows ‘SyS’ . Use [UP] or [DOWN] to select the option ‘rEST’ . Confirm with [ENTER] to reset the device to factory defaults. Crown FX LED Spotlight...
Strobe effect sound mode, all colour LEDs 0 … 5 No function 6 … 20 Strobe LED ring constantly on 21 … 250 Strobe effect, increasing speed, strobe LED ring 251 … 255 Strobe effect sound mode, strobe LED ring Crown FX LED Spotlight...
Strobe effect off 6 … 250 Strobe effect, increasing speed, all colour LEDs 251 … 255 Strobe effect sound mode, all colour LEDs 0 … 5 No function 6 … 20 Strobe LED ring constantly on Crown FX LED Spotlight...
Page 32
Operating Channel Value Function 21 … 250 Strobe effect, increasing speed, strobe LED ring 251 … 255 Strobe effect sound mode, strobe LED ring Crown FX LED Spotlight...
0 … 255 UV intensity (0% to 100%), PAR LEDs zone 2 0 … 5 Strobe effect off, zone 2 6 … 250 Strobe effect, increasing speed, zone 2 251 … 255 Strobe effect sound mode, zone 2 Crown FX LED Spotlight...
Page 34
Strobe effect, increasing speed, COB LED 251 … 255 Strobe effect sound mode, COB LED 0 … 5 No function 6 … 20 Strobe LED ring constantly on 21 … 250 Strobe effect, increasing speed, strobe LED ring Crown FX LED Spotlight...
Page 35
Auto programme 6, if channel 22 = 0 … 250 Sound programme 6, if channel 22 = 251 … 255 93 … 106 Auto programme 7, if channel 22 = 0 … 250 Sound programme 7, if channel 22 = 251 … 255 Crown FX LED Spotlight...
Page 36
Auto programme 14, if channel 22 = 0 … 250 Sound programme 13, if channel 22 = 251 … 255 209 … 222 Auto programme 15, if channel 22 = 0 … 250 Sound programme 13, if channel 22 = 251 … 255 Crown FX LED Spotlight...
Page 37
Auto programme 17, if channel 22 = 0 … 250 Sound programme 13, if channel 22 = 251 … 255 0 … 250 Programme speed increasing 251 … 255 Sound-controlled mode, specifies the auto programme / sound programme setting for channel 21 Crown FX LED Spotlight...
XLR chassis socket, 3-pin Power consumption 78 W Supply voltage 100 - 240 V 50/60 Hz Battery remote control Lithium-ions button cell CR2025, 3 V Fuse 5 mm × 20 mm, 1,6 A, 250 V, slow-blow Crown FX LED Spotlight...
Page 39
275 mm × 280 mm × 76 mm Weight Approx. 1.7 kg Ambient conditions Temperature range 0 °C…40 °C Relative humidity 20 %…80 % (non-condensing) Further information Similar design Combined device DMX control Master/Slave Remote control included Sound control Display Crown FX LED Spotlight...
Clean with a dry soft cloth. Stubborn dirt can be removed with a slightly dampened cloth. Never use solvents or alcohol for cleaning. Crown FX LED Spotlight...
Dispose the built-in lithium batteries together with the device. Check for an appropriate collection facility. Dispose of the batteries and rechargeable batteries at relevant collection points or through your local waste facility. Crown FX LED Spotlight...
Page 42
Repairing a device or passing it on to another user is an ecologically valuable alternative to disposal. You can return your old device to Thomann GmbH at no charge. Check the current conditions on www.thomann.de. If your old device contains personal data, delete those data before disposing of it. Crown FX LED Spotlight...