Reverse Function - Technics RS-TR474 Operating Instructions Manual

Playback (continued) —...
Reverse function
We fle FE sah [ace
The reverse function on this unit has three modes (= ,Co,
©). Read the descriptions below and select the mode as
desired. (Refer to step 4 on page 7.)
Tapetravel
Only one side of the tape (either the forward side
or the reverse side) will be played, and operation
will automatically stop when playback has been
completed.
Both sides of the tape will be played repeatedly
>) eight times, and then operation will automatically
stop.
oa (if playback is begun from the reverse side, the for-
ward side will be played seven times.)
When there is a tape in only one of the decks
Both sides of the tape wil! be played once, and
then operation will automaticaliy stop.
(if playback is begun from the reverse side, the for-
ward side will not be played.)
'When there is a tape in each of the decks
(ie) The forward and reverse sides of the tape in Deck
1 wilt be played, followed by the forward and
reverse sides of the tape in Deck 2, and after this
operation is repeated sight times, operation will
automatically stop.
(If playback is begun from Deck 2, the tape in
Deck 1 will be played seven times.)
To listen through headphones
Connect the headphones (not Included) to the
headphones jack.
Plug type: 1/4 inch phone plug, stereo type
Headphones
(not included)
Avoid listening tor prolonged periods of tims to prevent hearing
damage.
About the automatic-tape-select
function
This unit is equipped with the automatic-tape-select feature: it
automatically detects the type of tape being used. and then
makes the suitable adjustments of the bias and equalization ac-
cordingly.
About the remote control function
When connecting a Technics amplifier with the remote control
transmitter to this unit, you can operate this unit using a remote
contro! transmitter cf the amplifier. (This may not be possible with
some modeis.)
During operation from the remote control, the "FLC." indicator
-wi Eght up.
| mn no
Leds tia RC, C. u
&
eno 5 aL 3 pm tw
=
Deck "A.C." Deck 2"RC™
indication indication
About the Dolby noise-reduction
system
The Dolby nolse-reduction system is designed to effectively redu-
ce the annoying high-frequency "hissing" noise typical of
cassette tapes. During recerding, the system functions to in-
crease the high-frequency sound level, the sound, and then, dur-
ing playback, that same portion is weakened to Dring it back to
the previous !evel.
This unit includes two types of Dolby noise-recucticr systems.
the Dolby B NR-type and C NR-type.
Doiby B-type nofse-reduction
Noise is reduced to about one-third
Use this system when playing back tapes recoded by the Dolby.
B noise-reduction system, such as prerecorded music tapes. etc.
Dolby C-type noise-reduction
Noise Is reduced to about one-tenth
Use this system for the recording and playback of sourd sources
that have a wide dynamic range and good tone quality. such as
FM broadcasts of live performances, etc., and for playing back
such tapes.
'About the Dolby HX-Pro headroom
extension system
By functioning to improve the maximum output leve! of the {ape's
high-frequency range, this system permits recordings without a
reduction in the level of the sound source's high-frequency
range. In addition, by using the system in parailel with this unit's
noise-reduction system, recording and ptayback with a greatly ex-
tended dynamic range is possible.
Dolby noise reduction and HX Pro headroom extension |
manufactured under license from Dolby Laboratories Licens-
ing Corporation. HX Pro originated by Bang & Olufsen
"DOLBY", the double-O symboi DO and "Hx PRO" are
trademarks of Dolby Laboratories Licensing Corporation